Latest Firmware released
http://m.smoktech.com/detail?url=http://www.smoktech.com/support/upgrade/toolsandfirmware/ispalien
Don't know where you looked, but here is V1.2.11I just updated and it is now giving me V1.2.2 not v1.2.11
I dunno.
Yeah I am not the best when it comes to upgrading these. It took sooo many tries for it to connect but I figured it out. I am now the proud owner of V1.2.11Don't know where you looked, but here is V1.2.11
http://www.smoktech.com/support/upgrade/toolsandfirmware/ispalien
Good you got it! Great mod!Yeah I am not the best when it comes to upgrading these. It took sooo many tries for it to connect but I figured it out. I am now the proud owner of V1.2.11
ha lol i take that back. i was thinking 1.2.1.1Yea, 11 is less than 2!
24mg does that.ha lol i take that back. i was thinking 1.2.1.1
my brain farted for sure.
Can I upgrade to the .11 straight from the 1.2.1? I never upgraded to the .2 and don't want to be left in the dust.
Yep.Can I upgrade to the .11 straight from the 1.2.1? I never upgraded to the .2 and don't want to be left in the dust.
Turn the Alien off then on, what firmware version do you see on the screen?Hi all,
So I was on an upgraded kick today, finally got my r200 to update, did the rx200s with the custom firmware and then finally my alien!
I did the upgrade but had one question, on the smok site it said that the config had to be 00013000, but my config was not changeable and read FFFFFFFF.
It looks like the upgrade worked as I see the new coil select screen, but I wanted to make sure I did everything correctly or if I needed to change something regarding that config file?
I see the new versionTurn the Alien off then on, what firmware version do you see on the screen?
Then you are good.I see the new version
I haz a sad.... Upgraded my software and it reset my puff counter... On the bright side it reads my ohms better now.
And my juice tastes better... weird.
I suppose that could be possible, being that the update tweaks settings.And my juice tastes better... weird.
Don't laugh I was at 15000 puffs.
I'm on the latest version. Works great for me but u haven't tested the temp controlI'm debating on upgrading. My Alien is brand-new and working fine, and I haven't tried any TC. Plus, I haven't had any misfires, so I think I'll wait.
After the update, I notice more accurate ohm.I'm on the latest version. Works great for me but u haven't tested the temp control
Sent from my SM-G935V using Tapatalk
I haven't seen a video on it. I could always make one if needed but it's pretty simple. The site gives step by step detailsAnyone have a link to the best video showing the procedure? I'm aware there's a lot of steps, and apparently I have to hold the fire button the whole time (after removing batteries), so it has to be done one-handed, then? I'd like to get it right the first time (obviously), and want to make sure everything's prepared so there aren't any hiccups.
My advice is never adjust the ohmsWell, I went ahead and did it. Pretty painless and easy, really. Vape does seem a little smoother with my Q2 coil.
Just curious...is there a reason why the Alien doesn't just assume there's a new coil every time and adjust accordingly? Does that have something to do with memory presets (if you've manually adjusted the ohms?)
Misprint, scroll down the page and look!Weird. This picture says 0.2, but another picture says 0.4.
When you chose all file types did you navigate to the update bin file then select that one only ?I had no trouble updating my G2 and Slice, but I could not get the Aliens to update. I finally figured out to choose "all file types", and it told me "file too large". I just had to give it up. Computes piss me off, which is why I don't own one anymore.
Yeah, but by that point I had been asked to "open file with..." one too many times. Once I chose to open with IE, and stuck me with that from then on. I tried deleting and redownloading the .zip, but it kept wanting to open the .HEX file with IE because I told it to the first time. It's been 7 or 8 years since I owned a pc, and I've pretty much forgotten how to use one.When you chose all file types did you navigate to the update bin file then select that one only ?
Is yours a model B? My screen just asks if it's a new coil, with a "Y" "N" choice.
That's weird. I'm at 1.2.2, and I just get this.