Yep about the only real difference is the dogleg down in the airflow.
Which imho will be a negative thing.
Yes I know Lucy, always with the negative waves
Last edited:
Become a Patron!
Squonkers are Bonkers
- Thread starter DogMan
- Start date
Yep about the only real difference is the dogleg down in the airflow.
Which imho will be a negative thing.
Yes I know Lucy, always with the negative waves
Well Stimy Vapor v6 , with switchfet arrived , has some flaws , some fiddly bit
But works well ,
Front sqounker button , installed a lolly stick on back of front Sqounker button gives it a bit more length to push on the bottle crude but works ,
,
Small size
82.5mm x 47mm
Has a different sqounker cap a slot and collet that fits on the base of 510 ,
Sent from my ONEPLUS A3003 using Tapatalk
Has an oring on underside of 510 , one in cap , so it dont need to fully pressed in for a seal , half round silicone bottle ,
2 down sides the button could of been deeper / longer so wouldn't need a lolly stick in back
An the bottle cap can pull off some times when removing the bottle , if pushed full-on it can touch the board / switchfet , ?
These can be fixed by using a standard sqounker bottles an tube to 510. , An a lolly stick so not perfect ,
But works well ,
Front sqounker button , installed a lolly stick on back of front Sqounker button gives it a bit more length to push on the bottle crude but works ,
,Small size
82.5mm x 47mm
Has a different sqounker cap a slot and collet that fits on the base of 510 ,
Sent from my ONEPLUS A3003 using Tapatalk
Has an oring on underside of 510 , one in cap , so it dont need to fully pressed in for a seal , half round silicone bottle ,
2 down sides the button could of been deeper / longer so wouldn't need a lolly stick in back
An the bottle cap can pull off some times when removing the bottle , if pushed full-on it can touch the board / switchfet , ?
These can be fixed by using a standard sqounker bottles an tube to 510. , An a lolly stick so not perfect ,
Last edited:
Running VTC5 cell @ 4.18V ,
So little voltage drop , tested with smok volt ohm checker
Led colours show voltage levels of cell , change as volts drop , green blue then red which lights up under resin panel a little brighter indicating batter needs changing before board cuts out ,
[
Sent from my ONEPLUS A3003 using Tapatalk
So little voltage drop , tested with smok volt ohm checker
Led colours show voltage levels of cell , change as volts drop , green blue then red which lights up under resin panel a little brighter indicating batter needs changing before board cuts out ,
Sent from my ONEPLUS A3003 using Tapatalk
for accurate voltage drop test measurements must be made under load.
One at the atty while firing and one at the battery when firing.
the difference is the mod voltage drop.
a .1 ohm resistance has NO voltage drop at no current or just a few ma to run a meter.
However a .1 ohm resistance has a 2 volt drop at 20 amps.
One at the atty while firing and one at the battery when firing.
the difference is the mod voltage drop.
a .1 ohm resistance has NO voltage drop at no current or just a few ma to run a meter.
However a .1 ohm resistance has a 2 volt drop at 20 amps.
3.41 at the atty
3.83 at the battery contacts.
Just took those measurements on a pulse BF mod with a .2 coil in a Wasp.
So the mod voltage drop is .42 volts....
the total voltage drop between Neg battery contact and neg post on Atty = .1 V
the total voltage drop between positive 510 pin and positive atty post =.06
So total atty drop could be considered .16 volts.
But this includes the drop in the connection between the atty and the mod 510.
so at best the Pulse BF mod has a .26 V drop in the mod not counting the atty to mod 510 connections.
this is at 17 amps. Using a VTC5A fully charged at 4.19V
With no atty on the Pulse BF it reads 4.18 volts at the 510 while firing with NO atty.
Edit rechecked drop to atty. on the negative side it was .02 from the negative battery atty post to the negative portion of the 510 inside the mod. There is a .14 volt drop between the negative battery contact and the negative portion of the 510.
This places the Actual internal mod voltage drop at .39 volts.
3.83 at the battery contacts.
Just took those measurements on a pulse BF mod with a .2 coil in a Wasp.
So the mod voltage drop is .42 volts....
the total voltage drop between Neg battery contact and neg post on Atty = .1 V
the total voltage drop between positive 510 pin and positive atty post =.06
So total atty drop could be considered .16 volts.
But this includes the drop in the connection between the atty and the mod 510.
so at best the Pulse BF mod has a .26 V drop in the mod not counting the atty to mod 510 connections.
this is at 17 amps. Using a VTC5A fully charged at 4.19V
With no atty on the Pulse BF it reads 4.18 volts at the 510 while firing with NO atty.
Edit rechecked drop to atty. on the negative side it was .02 from the negative battery atty post to the negative portion of the 510 inside the mod. There is a .14 volt drop between the negative battery contact and the negative portion of the 510.
This places the Actual internal mod voltage drop at .39 volts.
Last edited:
4.17V on cell when just checked on charger,
still awaiting them to fully charge
So .15 different on pic ,
was 4.09 , on first press or 2 before camera focused so it drops quick each press since cells not fully charged yet ,
Sent from my ONEPLUS A3003 using Tapatalk
Second pic ohms
Will try volt meter on battery contacts an such later not got one with me at moment
Last edited:
Still not accounting for battery sag.4.17V on cell when just checked on charger,
still awaiting them to fully charge
So .15 different on pic ,
was 4.09 , on first press or 2 before camera focused so it drops quick each press since cells not fully charged yet ,
Sent from my ONEPLUS A3003 using Tapatalk
Second pic ohms
and what is your atty resistance? Must be fairly high. Batteries sag to 3.8-3.7 at around 15 amps.
My measurements on the BF are accurate.
It is a matter of measuring at various points in a series circuit to check voltage drops at the different places.
Not picking on you Benley but the generally accepted method of checking mech mod voltage drop is garbage.
One MUST read the voltage at the battery and at the 510 while firing with a load to get an accurate voltage drop.
And as the current increases due to lower resistance coils the voltage drop WILL increase.
As will the battery sag, but they are 2 separate things.
One MUST read the voltage at the battery and at the 510 while firing with a load to get an accurate voltage drop.
And as the current increases due to lower resistance coils the voltage drop WILL increase.
As will the battery sag, but they are 2 separate things.
Nah thats fine , need to know how its done properly,
Ive only got minimal vape gear with me at my partners ,
I do have a cheap volt meter at home so will test them when get the chance @ home ,
I've only got the volt/ omh tester a few atties an 510 ohm meter few building bit with me here basically bare min essentials.
So need reading at both battery contacts , an then at 510
Both under load ,
Sent from my ONEPLUS A3003 using Tapatalk
Yep just pop the top on the atty and read at the posts while firing and read at the battery terminals while firing. the difference in the reading is the total voltage drop including the atty drop.
to eliminate the atty drop read at the 510 inside of the mod while firing.
I figure atty drops will vary a bit but should not vary much, if they do might need to dissassemble and clean the atty.
I just got a .03 total voltage drop from the 510 inside the mod to the posts on the atty.
Which is basically nothing.
All good! Congrats!
Where did bear go?
Just a whooshing sound and gone....
Just a whooshing sound and gone....
nuppin lasted 4 minutes too lol
Just a heads up Bonkos: I put my G10 Mum’s Plug Mech Squonk up for trade in the classies. Check her out!
Sent from my iPhone using Tapatalk Pro
Sent from my iPhone using Tapatalk Pro
Purdy
First regulated squonk just kinda happened out of no where. Gotta say it looks and feels really nice.
Sent from my SM-G955U using Tapatalk
Sent from my SM-G955U using Tapatalk
JuicyLucy
My name is Lucy and I am a squonkaholic
VU Donator
Diamond Contributor
ECF Refugee
VU Challenge Team
Member For 5 Years
This is vindicating -
Still can't believe its as popular as it is - extremely unsatisfying vape
Understandable, it starts off with a fresh battery and vapes like it has a 2/3 charged one in there.
Using the same battery and atty the Pico Squeeze puts 3.67 volts to the atty posts....
VS 3.41 for the Pulse BF.
VS 3.41 for the Pulse BF.
Bear is busier than a one legged man in a ass kicking contest! Yes, I saw them goodies but I figured I let someone else try a Nuppin
About time to find out if I’m going to suck out harder on not getting a Half as badly as me bombing on learning Japanese (Japan needs a Sesame Street type program)
I get 3.74v Fresh 5A on Pico with my Haku Crusier... 3.63v with the Ha-Klone
JuicyLucy
My name is Lucy and I am a squonkaholic
VU Donator
Diamond Contributor
ECF Refugee
VU Challenge Team
Member For 5 Years
Interesting - the Pico seems significantly peppier vs the Pulse
I said something on the Facebook group for pulse and pulse things. I got flammed. They were talking about a fix and I said something like get a real mech lol
Sent from my LG-D850 using Tapatalk
It will depend quite a bit on your coil resistance as a lower ohm coil will draw more current causing more battery output voltage sag. I was using a .2 coil for my tests.
voltage drop will vary a bit with different attys as well.
Well they could not have bought a mod that was not the best could they?
the Pulse actually performs a tiny bit better than the beat up CV I use.
But the Pico beats em both by a mile.
Mosfets rule!
JuicyLucy
My name is Lucy and I am a squonkaholic
VU Donator
Diamond Contributor
ECF Refugee
VU Challenge Team
Member For 5 Years
No shit
My mechs (brand new) cost anywhere from $12 (Frankenclone) to $450, but most are in the $50 range, and the Pulse was hands down the worst mod I ever owned
So bad I refused to sell it to some unsuspected schmuck
When I first saw the Pulse... and then Tony's video... I said Immediately that it was a leaverite.
Some things I will venture and try at the <$35 mark, but that fucking thing was a no from the beginning. Not a maybe, or a possibility...just straight...
Some things I will venture and try at the <$35 mark, but that fucking thing was a no from the beginning. Not a maybe, or a possibility...just straight...
Did better on the Half mods than me trying to learn Japanese
Japanese is an extremely difficult language. I studied it in college and am not even close to fluent.
Regarding the Half, I gave up on that. Too difficult and too expensive. Doesn’t help that I work every Sunday!
Sent from my iPhone using Tapatalk Pro
JuicyLucy
My name is Lucy and I am a squonkaholic
VU Donator
Diamond Contributor
ECF Refugee
VU Challenge Team
Member For 5 Years
That was my thought too - but got caught squonkless in Seattle and took me three B&Ms to find any squonker - the first one I tried had never heard of the concept
Desperate times - but it was a lot worse than I thought it would be
Looking for a wood Half. Thanks tho. One of these days will be my day.
Yeah, it’s as hard as English to learn
Might have something to do with using three different writing systems in combination and all the contractions they use. I’ve forgotten more than I learned somehow!
Sent from my iPhone using Tapatalk Pro
Those are good mods, but we want the one you have to get lucky for - stab wood/delrin combos.
I did get one of the printed ones - and it's not only a unique design, it works great - so I still want one of the more handcrafted ones - for what they are (well made, hand finished, nice materials), they're actually not priced crazy...but they only make like 6 a week...
I did get one of the printed ones - and it's not only a unique design, it works great - so I still want one of the more handcrafted ones - for what they are (well made, hand finished, nice materials), they're actually not priced crazy...but they only make like 6 a week...
Constant use of puns being it by sound or how it’s written blows my mind.
It’s basically how we use slang and having words have a ton of different meanings in it’s usage but way more complex
Maybe I'll just buy a flave 22
Sent from my SM-G955U using Tapatalk
Sent from my SM-G955U using Tapatalk
The flave is awsome i got 2 nn caps comeing for it that will prob make it even better
Sent from my SM-G950U using Tapatalk
Was on FT last night and it looks like the Kanger DB160 and the original DB are going bye bye.
Kanger getting ready to come out with a new dual battery squonker?
I figure the Pico squeeze killed the DB.
Kanger getting ready to come out with a new dual battery squonker?
I figure the Pico squeeze killed the DB.