Become a Patron!

Bottom feed Noisey Cricket V2 Conversation

ben73

Gold Contributor
Member For 4 Years
Ok so here is a little view and steps to bottom feed Noisey Cricket V2 conversation.

Parts
Noisey Cricket V2

Mod maker bf 510 ,

Or one from Fasttech with the threaded contact nut to 510 pin (needs to be threaded for metal feed tube). 510 link below ... https://www.fasttech.com/p/8689000

Mod maker bf metal feed tube
Mid maker bottle that fits the feed tube
Silicone bottle washers
Soldering iron ( one joint to solder 2 to desolder)
Dremel cutting discs
Dremel,
Time an patience.



Take the blk tap off top plate off the top of the mod
to get to screws to allow dismantling of mod ,

Take top off mod , and side , potential meter off, allows you to lift pcb and top off,

Once inside , unscrew 2 screw to the board allows top plate to come off , and unsolder the postative 510 wire from the 510

Then the postative wire to battery contacts unsolder one of them,
Directly under the 510
its the one in pic now hanging over the side of the mod directly under where 510 sits ,

( this will be where bf 510 sits down into battery tube )
so the green plastic contact part will need removing too ,

The green plastic that is the top posative contacts for both cells. It has 2 screws in the center take them out,
and remove the green plastic,

You now cut the green plastic in half pictured to remove the part under 510 ,

leaving the 2 screw points on the green plastic
to still be to attach to mod
and the half that sits under PCB still intact ,
now screw it back in leaving one side open directly under the 510

Mods Top plate .
Remove the 510,
i found this to be a pain
so after I had unsoldered the 510 wire off the 510 i was able to work away from the mod and remove the 510 by splitting it apart with a screw driver , ( not easy but do able )

That allowed me to just have access to 510 an top plate to them remove 510 without damaging anything else

once done you can install your new mod maker Bf 510 onto the top plate , with a threaded 510 pin , needs to be threaded to allow the bf feed tube to screw onto it,

Remove the posstive wire that connected the postative battery contact ( green plastic )you removed earlier,
remove the wire right down to the base of the mod this has a spring and contact that touches the bottom plate for P an S, this is not needed , so remove that piece of wire,


After you have installed your 510 , you solder the 510 posstive ring to the posative wire that comes from pcb - contact and connect up the 510.

You can assemble mod again and check if it still works using PCB with bottom battery plate in P mode for single cell ( all good )

Or skip.

Then disassemble again. Once tested, to cut feed tube and sqounker hole , so these are best done whilst its all disassembled again.

Using a mod maker metal 510 feed tube and the mod maker posative 510 pin , screw the tube onto the 510 , work out the length of tube needed then cut to required length ,

Remove the feed tube or can be damaged .

Now use tape or sticker / label an place over front of mod 510 side and mark out where you want your sqounker hole to be ,

Using a dremel / rotary tool and cutying disks , cut a hole out of the front of the mod for Sqounking with , then just file + sand smooth to size shape you want ,

Clean mod and metal filings off mod and board ect ,

Re-attache your sqounker metal feed tube to 510 cut to length ,

Assemble the the pcb to the top plate and 510 , re- assemble the mod ,

Using a mod maker Sqounker bottle with a cap wide enough to
Fit the feed tube , and a silicone washer inside bottle to seal tube and bottle cap , fill bottle attach to feed tube and slide into sqounker tube, insert battery an vape enjoy ,


Hope this helps anyone ,
You will still have a working On / Off , and low voltage protection . Same as in P mode on a Normal NC v2 in P mode, but will only be one cell being used.

Feed tubes last pic,

c7ce21f31afbafa9cbcef9632337bf6a.jpg
019b1635cfca49b980027b5172472be4.jpg
8fb9f76724e1d6ce5ccfa0cd376dc9bb.jpg
973d69ac7b3a353f6666949f5ea4fe72.jpg
513abd0b197b6131ba5e433b851f42fa.jpg
3ce887259a371457d59afd486ed9a73a.jpg
cfaac982e984c83715cf3d2019209ccd.jpg
621a93383b93a1c91d691518bfce39ce.jpg
f5aa964722b59f5af199bd3a3e5853e6.jpg
0a704aa93aff478a5bd745aeda95637a.jpg
066017a6e9daa2c5490b8affb0adee46.jpg
354174a6fef38aecd1f31b9a2a75b23e.jpg
3d9078f4fb60a0ba5f613b186342ac11.jpg
54c5b1ff4174f42a45f049b75c8b4295.jpg
c2091c202b640364dcfe8413e7489d4e.jpg
d9381c85517956cf793a4ddb32c18c43.jpg
b97871c7021ce51dda517cdcb7ed224d.jpg


Sent from my ONEPLUS A3003 using Tapatalk


Also be aware the sqounker tube is part of the 510 posative contact ,
So as a caution if using a metal cap on your sqounker bottle choose one smaller than outside of bottle diameter to be safe most are , but be aware,

An not to have it touching the inside of the mod. Can also cut to size your included battery sleeve inserts ,
684cb6ee1081ab1fe2729f117bf39ebe.jpg
258c87131ec40da64302376060f14502.jpg

cb4daa083a3a9d2f6739b6e49e03eadf.jpg
 
Last edited:

ben73

Gold Contributor
Member For 4 Years
Just had a few ask me how its done , and if i can do theres so easiest way is to show others ,
Heck its a good shaped little mod , loved my Coppervape V1 for past 2 years but wanted a more reliant vape that didnt need contact cleaning adjusting all the time , so did this ,

Sent from my ONEPLUS A3003 using Tapatalk

An mod wasnt much of a loss was front the first batches with potential meter but on backwards and no atty sat flush on the 510,

So actually improved on it.
 
Last edited:

ben73

Gold Contributor
Member For 4 Years
2 more in the making
A 25mm and a 22mm
The 22mm has a lot thinner mod walls , so easier to cut shape ,
This time i really taped / masked up the body up to stop stratches
ef07bab856bdebf6aa80c12055fbfdc2.jpg
2cbe6fccde6aa7ef0341cec403c926da.jpg
0039a30e7bdcce9d0a7a2d5323a0044e.jpg
4cbfd7f61208015cdd232bba79caa3a7.jpg


Sent from my ONEPLUS A3003 using Tapatalk
 

ben73

Gold Contributor
Member For 4 Years
Ok so I've just used Dremel to cut off the old 510 from Noisey Cricket V2 mod , was a heck of a lot easier that the first time i made one
Once you can cut most of the golden back through , it cat be split open and the 510 comes out a lot easier than prying it off like i did first time take your time,

This was the hardest part of the conversion removing this ,

Then its just back to the next steps in the guide to finish up the build conversion ,
5955b94bdcba50ce9c203decb16e6820.jpg
38bd96f8a38918a79ec3e590e84dc6a1.jpg


Sent from my ONEPLUS A3003 using Tapatalk
 

ben73

Gold Contributor
Member For 4 Years
Now have competed 2 more so own 2 x 25mm
1 x 22m
Noisey Cricket V2 Sqounker mod,s these are just same as switchfet type mods ,
At lower cost
And not a box square shape so sit well in hand.

42776586a28aef0bede7fe9f0905a1a9.jpg
2edc180d18ee19bb287d630e8f177d10.jpg
ed6441c1eb06ea340f7b2bc61b653967.jpg


Sent from my ONEPLUS A3003 using Tapatalk
 
Last edited:

AnthonyLouis

Silver Contributor
Member For 4 Years
Unlisted Vendor
Now have competed 2 more so own 2 x 25mm
1 x 22m
Noisey Cricket V2 Sqounker mod,s these are just same as switchfet type mods ,
At lower cost
And not a box square shape so sit well in hand.

42776586a28aef0bede7fe9f0905a1a9.jpg
2edc180d18ee19bb287d630e8f177d10.jpg
ed6441c1eb06ea340f7b2bc61b653967.jpg


Sent from my ONEPLUS A3003 using Tapatalk

Planning to sell them?


Sent from my iPhone using Tapatalk
 

ben73

Gold Contributor
Member For 4 Years
Planning to sell them?


Sent from my iPhone using Tapatalk
I dont know keep getting ask on Facebook sites about selling them ,
an my answer is luxotic mod is much cheaper to buy.
If i did they cost me XX £s an then my time effort ?
and extra parts i have to buy to enable them to become Bottom feed
as well as tools cutting discs ,
sanding filing polishing

Whats a fair Price ?
Its got to be over my overall costs to be worthwhile doing it.
An Allow me to reinvest into buying more parts for more.

Parts can cost around similar to cost of the mod new.

Then there the time and effort put into them and making a nice finish
As doing for your own use your time isnt facterted in as its for personal use.


Sent from my ONEPLUS A3003 using Tapatalk
 

AnthonyLouis

Silver Contributor
Member For 4 Years
Unlisted Vendor
I dont know keep getting ask on Facebook sites about selling them ,
an my answer is luxotic mod is much cheaper to buy.
If i did they cost me XX £s an then my time effort ?
and extra parts i have to buy to enable them to become Bottom feed
as well as tools cutting discs ,
sanding filing polishing

Whats a fair Price ?
Its got to be over my overall costs to be worthwhile doing it.
An Allow me to reinvest into buying more parts for more.

Parts can cost around similar to cost of the mod new.

Then there the time and effort put into them and making a nice finish
As doing for your own use your time isnt facterted in as its for personal use.


Sent from my ONEPLUS A3003 using Tapatalk

Your absolutely right. I saw how good it looked and jumped the gun haha. Didn’t think about anything else!!


Sent from my iPhone using Tapatalk
 

ben73

Gold Contributor
Member For 4 Years
Your absolutely right. I saw how good it looked and jumped the gun haha. Didn’t think about anything else!!


Sent from my iPhone using Tapatalk
Thats it people see
An go ah it's a cheap enough mod,
so should be cheap cheap selling cost ,
but the companies that do this buy in massive bulk buys , wismec uses 510s that are not even 1usd each and probably the worst ever used,
when we buy them we pay 5 x or 10 x that for good one since
we build ours to last
for our own personal use,
Sn pay extra to have it be better quality as well.

Hence why small modders an makers charge so much ,
Start up costs ect plus
there over heads with not bulk discount buying
adds up quickly

China can beat every one
Every time on lower cost
of materials or goods
due to cheaper labour
bulk buying and cheaper materials used,

Sent from my ONEPLUS A3003 using Tapatalk
 

ben73

Gold Contributor
Member For 4 Years
Awesome job! Now if only wismec will come out with a factory Noisy Cricket II-25 dual battery Squonker with all the same functions of the original.

Sent from my SM-G930R4 using Tapatalk
Or maybe use board in your own built mod , ive asked if they will make a 21700 noisy Cricket v2 type , then will have good amps 30ish an 3500mah so lnger run time , should be good for 24-25mm atties dual coil

Sent from my ONEPLUS A3003 using Tapatalk
 

ben73

Gold Contributor
Member For 4 Years
Parts from one shop,

Mod maker 510 ,
http://www.modmaker.co.uk/MM510-Squonker-Connector

Mod maker feed tube
http://www.modmaker.co.uk/MM510-Squonker-Connector-Extension-Tube-Kit

Mod maker Dinky plus bottles,
http://www.modmaker.co.uk/MM-Dinky-10-Silicone-Squonker-Bottle-Kit-Light

Bottle seals for metal tube,
http://www.modmaker.co.uk/Silicone-Washer-Seals-10mm-OD-x-3mm-ID-Pack-Of-10

And just follow the basic guide above , the built in chip works on one cell , just remove the bat terminals from bottom plate , you don't want feed tibe making contact , i also removed the wires leading to plate as well
only for the side which the bottle goes into,
 

ben73

Gold Contributor
Member For 4 Years
Still going strong, was thinking if ever modog V2 nano 510s where ever in stock I was wondering if trying one and the mod dog gatterling bottle then should hot swap bottle to 510 pin same wiring but rodium and silver plated parts if using silver wire should give a slightly better conductivity, if I can get the part as never in stock maybe try one,
But currently using dinky plus with le Concorde RDA
 

VU Sponsors

Top