Become a Patron!

Has anyone seen the new Reload S rda?

nadalama

Senior Moderator
Staff member
Senior Moderator
VU Donator
Diamond Contributor
Member For 4 Years
VU Patreon

f1r3b1rd

https://cookingwithlegs.com/
Staff member
Senior Moderator
VU Donator
Diamond Contributor
VU Challenge Team
Member For 5 Years
VU Patreon
The clone vapes great, but I haven't tried the authentic so can't compare.
That’s all I need to know
Ima have to pick one up
 
Do other Attis sit flush? It looks like either the atty is on a slight angle or the mod is shaped a little rolled in front. The back side looks flush

Alright... So I'm cursed. I found that my other atomizers sit flush so I took a look at the 510 on the S and saw it was a little wonky. Cool, easy fix. I unscrewed the 510, took it out and began screwing it back in... All was going well till I heard a pop and it just fell out. Looks like the squonk pin snapped off in there.

R5I4CXb.jpg


I just started laughing because this has been so stupid. FML.
 

KingPin!

In my defence, I was left unsupervised ^^
VU Donator
Platinum Contributor
Member For 4 Years
VU Challenge Team
Reviewer
Over tightening perhaps? Or threading got snagged
 

VinnySem

Silver Contributor
Silver Contributor
Member For 4 Years
Contact the vendor and get it exchanged. Seems like you got a bad one, it really is a great atty, absolute flavor bomb and can chuck some clouds with the right build
 
Also for me on topside dual it does not sit flush.
Best atom ever used btw, I like how fast is to put a new build in. Thinking to buy a clone just for change the colour of the atom. Anyone know if the clone cap is it compatibles?
 
Am I the only one that gets vicious spit back from this device? I want to like this thing so much but it spits no matter how I wick or position the coil. I can't be the only person out here with this problem?
 

Letitia9

Citrus Junkie
VU Donator
Platinum Contributor
Member For 4 Years
VU Challenge Team
Am I the only one that gets vicious spit back from this device? I want to like this thing so much but it spits no matter how I wick or position the coil. I can't be the only person out here with this problem?
Have you tried to space the coil just a fraction?
 

St.Roostifer

Gold Contributor
Member For 5 Years
Was just vaping mine and after a fresh squeeze I do get noticeable spitback. Never payed much attention before because I have a 510 drip tip on mine so the majority of the spray is kept in the chamber. But I can hear the cracking and spitting, lol.

Could try to restrict the airflow combined with a lower wattage.
 

PoppaVic

Gold Contributor
Member For 4 Years
Running a 4-loop flapton, 3mm ID, around 0.25Ω and 41w; airflow nearly wide open.

Doesn't spit at all.. Even going up to 50 or so, it's just "too hot" for me. Yes, on occasion I hear a crackle, but no spitback - and I'm using an 810.
 

Vape Fan

_evil twin_
Staff member
Senior Moderator
VU Donator
Platinum Contributor
Press Corps
Member For 5 Years
No spitback. .29 SS Alien / 300F - 35W / Open air
 
I guess I just suck at vaping in general. Last night I sat down determined to figure this out and after a day at work and back using this new coil install there are no issues with spitback anymore.

hGowufV.jpg


ck7QIvR.jpg


wJF6VKP.jpg


I cut the legs to 4mm in height. I thought that maybe a large part of the reason I was getting my mouth burned to shit was because I was setting the coil too low in the chamber. I thought maybe the coil being too low meant that if I oversquonked all that juice was saturating the bottom of the coil and shooting into my mouth when I went to bigg succ the thing. I also made sure the wick was very tight with the roll method. So the lesson I learned was just to set the coil higher and make sure the wick is tight. Duh. Does the trick for me.

Reading 0.21Ω at 60 watts and no spitback.

I'll get gud at this stuff one day.
 

VU Sponsors

Top