HELP!!! KRIS CLAPTON DC WIRES

Discussion in 'Ask An Expert' started by RaiderRagsag, Jul 17, 2017.

  1. RaiderRagsag

    RaiderRagsag New Member

    Blog Posts:
    0
    Joined:
    Jul 17, 2017
    Messages:
    6
    Can anyone help me about DC WIRES KRIS CLAPTON 26g? What build would be recommended using it on parallel box mod(unregulated MOD) i have a pair of LG HG2's and a pair of Sony vtc4. What would you guys recommend also? TIA :)
     
  2. PhantomOp

    PhantomOp VU Donator Gold Contributor

    Blog Posts:
    0
    Joined:
    Nov 5, 2016
    Messages:
    1,849
    Greetings RaiderRagsag, and welcome to VU.

    As you are new here, and we don't know your experience level with MECH devices, and the question that your asking leads me to think you are inexperienced with MECH devices, I would have to say "put it on the shelf, forget about it, and go purchase a regulated MOD".

    However, if you want to continue forward with a MECH device ...

    1) Learn ohms law. You must know this before attempting to wrap or build any customs coils for a MECH device.

    2) Know the differences between a PARALLEL and SERIES box mod.
    Here is a good "graphical" reference of the two --
    https://www.zamplebox.com/community...egulated-series-box-mod-vaping-battery-safety
    [​IMG]

    3) Learn to LOVE http://www.steam-engine.org -- this site has many / many / many calculators for you to use for building and learning your devices.

    4) Dig through our MECH section on this forum. There is a TON of information out here to learn off of.
    http://vapingunderground.com/forums/unregulated-mechanical-mods.406/


    Absolutely ---
    What atomizer are you building for? Single coil or Dual coil?
    Based on the MOD you mentioned, keep the Ω between .2Ω and 1.0Ω.

    Based on some google searching, I ran across this build spec for the mentioned wire. --- I personally would say not to run these coils in a MECH if you are new to MECH devices.

    DC Wires! Kris Clapton!!
    26g
    8 wraps/9 loops
    3mm guide
    dual coil!
    reading at .20 ohms

    In reference to the batteries that you mentioned ---
    I personally would not use the HG2 batteries in a MECH device, as they are rated at 18A max.
    Since you have them, I would use the VTC4 (23A battery) over the HG2s...

    However, the Sony VTC5A (25A) is recommended for MECH devices, from what I've seen others recommending.

    Mooch's Recommended Batteries
    https://www.e-cigarette-forum.com/forum/blog-entry/moochs-recommended-batteries.7593/
     
    Last edited: Jul 17, 2017
    gakudzu likes this.
  3. RaiderRagsag

    RaiderRagsag New Member

    Blog Posts:
    0
    Joined:
    Jul 17, 2017
    Messages:
    6
    Im trying to run a dual coil. So if that build you mentioned 8wraps/9 loops would be cut in half instead of .2ohms it would be on .1something for 5wraps/6loops? So according to your amp load chart.

    Vtc4-----> 23A+23A(beacause my mod is parallel)= 46A LOAD right?

    Then 5wraps/6loops dual coil would be on .1 something.

    Would it be safe then? Because i would have a 46A capacity using a vtc4 for that .1 something build?

    Btw thanks for the response :)
     
  4. RaiderRagsag

    RaiderRagsag New Member

    Blog Posts:
    0
    Joined:
    Jul 17, 2017
    Messages:
    6
    And also i dont chain vape :) i dont like my batteries getting hot:)
     
  5. PhantomOp

    PhantomOp VU Donator Gold Contributor

    Blog Posts:
    0
    Joined:
    Nov 5, 2016
    Messages:
    1,849
    Wrong. If you are going to run dual-coil build, you will have to have both coils at 8wraps. Adding the second coil is what splits your total Ω in half, not by reducing the # of wraps.

    In a parallel MECH mod, that is correct. You would have 46A available.

    I'm not a MECH mod user -- so I will stop and ask someone with more MECH experience to chime in.

    IMO -- I would not do it, because I am not an experienced MECH mod user. If your not an experienced MECH mod user, I wouldn't recommend it for you either. If that is your kid in your avatar picture, put the MECH away for another day, get yourself a regulated MOD, and stay alive.
     
    Last edited: Jul 19, 2017
  6. RaiderRagsag

    RaiderRagsag New Member

    Blog Posts:
    0
    Joined:
    Jul 17, 2017
    Messages:
    6
    Ok sir :) thanks for the advice and informations :) luckily a year using my mech MOD with many types of build on it i havent had any worst scenarios yet :) thanks again sir :) im getting a regulated mod soon :) and learn deeper on my mech MOD but in safe conditions :)
     
  7. RaiderRagsag

    RaiderRagsag New Member

    Blog Posts:
    0
    Joined:
    Jul 17, 2017
    Messages:
    6
    DC Wires! Kris Clapton!!
    26g
    8 wraps/9 loops
    3mm guide
    dual coil!
    reading at .20 ohms
    ______________________

    last question btw.

    Its says its already on dual coil.

    Do i have to split it again?

    What i mean is (9 loops × 2 coil = 18 loops build or .2ohms)right?

    So(5 loops x 2 coil = 10 loops but ????ohms)

    JUST CURIOUS THOUGH...
     
    Last edited: Jul 19, 2017
  8. PhantomOp

    PhantomOp VU Donator Gold Contributor

    Blog Posts:
    0
    Joined:
    Nov 5, 2016
    Messages:
    1,849
    Good catch on that one --- I completely missed that. I miss read it and though it was .2Ω p/coil.
    So --- that would make them .4Ω p/coil @ 8 wraps p/coil.
     
  9. RaiderRagsag

    RaiderRagsag New Member

    Blog Posts:
    0
    Joined:
    Jul 17, 2017
    Messages:
    6
    Thanks again :)
     

Share This Page

Close This Message