Become a Patron!

Help with Vandy Vape Pulse BF Kit (coils)

So I have two questions here:

1) I have a Vandy Vape Pulse BF Kit ( https://www.vapewild.com/vandy-vape-pulse-bf-squonk-kit/ ) and I am looking to buy the Coilology Performance Pre-built coils ( https://www.vapewild.com/coilology-performance-7-in-1-prebuilt-coils-set/ ). Will all of these coils be 100% safe to use doing a single coil build on my device? I run a Golisi 20700 batter. Here are the specs for it.
  • Capacity: 3200mAh
  • Nominal Voltage: 3.7V
  • Cut off charging Voltage: 4.2V
2) Now, I tried to figure this out myself by using the Ohm's Law Calculator ( https://www.misthub.com/blogs/vape-tutorials/76788933-tutorial-ohms-law-and-vape-safety-calculator ). I inputted the volts as 3.7 (nominal voltage for battery) and inputted one of the coils from the Coilology set which was rated 0.36ohms. This put me at 10.27 AMPS and 38 WATTS. I guess I just don't understand if that's safe or not. What is unsafe? And what is safe? Lol, I apologize for being such a newb. Any help though is greatly appreciated.
 

VAPEROXX

Gold Contributor
Member For 4 Years
Unlisted Vendor
So I have two questions here:

1) I have a Vandy Vape Pulse BF Kit ( https://www.vapewild.com/vandy-vape-pulse-bf-squonk-kit/ ) and I am looking to buy the Coilology Performance Pre-built coils ( https://www.vapewild.com/coilology-performance-7-in-1-prebuilt-coils-set/ ). Will all of these coils be 100% safe to use doing a single coil build on my device? I run a Golisi 20700 batter. Here are the specs for it.
  • Capacity: 3200mAh
  • Nominal Voltage: 3.7V
  • Cut off charging Voltage: 4.2V
2) Now, I tried to figure this out myself by using the Ohm's Law Calculator ( https://www.misthub.com/blogs/vape-tutorials/76788933-tutorial-ohms-law-and-vape-safety-calculator ). I inputted the volts as 3.7 (nominal voltage for battery) and inputted one of the coils from the Coilology set which was rated 0.36ohms. This put me at 10.27 AMPS and 38 WATTS. I guess I just don't understand if that's safe or not. What is unsafe? And what is safe? Lol, I apologize for being such a newb. Any help though is greatly appreciated.
What is the amperage rating for your battery?

http://vapingunderground.com/threads/wts-wtt-aspex-performance-coils.434798/
 

MrMeowgi

The Vapin' Drummer
VU Donator
Diamond Contributor
Member For 4 Years
The batteries are rated to 25 amps so yes this is a safe build. You want to make sure to keep it under 25 amps. Research research research. It's your best friend. And welcome to the Vu. Ohms law is a must when dealing with mechanical mods. The coil you install determines the wattage and power from the battery. You are your only safeguard with a mech.
 
The batteries are rated to 25 amps so yes this is a safe build. You want to make sure to keep it under 25 amps. Research research research. It's your best friend. And welcome to the Vu. Ohms law is a must when dealing with mechanical mods. The coil you install determines the wattage and power from the battery. You are your only safeguard with a mech.

Thanks for the help! So any coil will be safe if I use the Ohms Calculator and keep it under 25amps, which is the amp rating of the battery. Right? And is 10amps too weak?
 

MrMeowgi

The Vapin' Drummer
VU Donator
Diamond Contributor
Member For 4 Years
Thanks for the help! So any coil will be safe if I use the Ohms Calculator and keep it under 25amps, which is the amp rating of the battery. Right? And is 10amps too weak?
Yes. Keep it below the 25amp limit. 10amps isn't too weak. The lower you build on a mech the more wattage you get due to ohms law. So a. 15 ohm coil would pull just over 25 amps. I recommend an app called Vape Tool. Easy to navigate. I've been using it for years. Has ohms law calculator. Wire build section so you'll know what ohms you should have before testing and putting on a mech
0daff68e250d550f1e62b9a6349a7e9c.jpg
 

VU Sponsors

Top