Newbie here need some advise

[Donald Bickers]

thanks, i'm waiting for a reply.

did you find out anything

 

[HackitZ]

I'm back.
Ok my nemesis mod came.
so i have the mod, kayfun lite plus and 2 350 batteries.
I don;t have any wire or cotton for the coil.
I do have the two coils that came with the kayfun (i cut off most of the wore after the coil). i installed that coil in my kayfun.
I get no vap, feels like it's plugged when i hit it. I checked my resistance with a volt meter and I'm about 1.1 ohms.
i have both air holes lined up but it feels like sucking on a thumb.
any help would be greatly appreciated.

 

[Donald Bickers]

does it have adjustable airflow

 

[HackitZ]

yes two holes and they are lined up to the ring with two holes.

 

[Donald Bickers]

can you drain the juice out and see if it still does the same thing,,,,can you take a pic of it so I know what model you have

 

[HackitZ]

can you tell from this pick.

 

[Donald Bickers]

can you tell from this pick.View attachment 10645

does it have a set screw in the air hole for adjustment,,,,or if you could take a pic of the airflow area

 

[HackitZ]

yeah it has an airflow screw. i removed it and it's still no airflow.

 

[Donald Bickers]

yeah it has an airflow screw. i removed it and it's still no airflow.

there is something restricting the airflow ,,,,I wish I was just there,,,,can you tear it completely down(the base part)and see if may be there is some packing or something blocking it

 

[Donald Bickers]

you have good equipment so don't give up on it,,,its something simple im sure

 

[HackitZ]

taken apart

 

[Donald Bickers]

wipe it off if you don't want juice on your face and see if you can blow through it from the top side through that center tube below where the wick goes

 

[HackitZ]

in the above pic, see the white little plastic piece? it came out when i removed the one side of the coil. put it back together and now have airflow. not sure if it should be there or if it can be removed.

 

[Donald Bickers]

that's your insulator for your positive pin you need that or you will have a dead short,,,,just lay that where it goes and see if you have airflow

 

[HackitZ]

needs the white piece, with it out no resistance.

 

[Donald Bickers]

yea you gotta have that,,,,put it together without the air screw and see if you have airflow

 

[HackitZ]

no its like sucking on your thumb

 

[Donald Bickers]

its not making sense,something is blocking it,,,,,you need to take the airflow screws out and see if you cant find your blockage ,,,,do you have some fine wire you could use like a roto rooter to find your blockage

 

[Donald Bickers]

Rufus need to go outside ,BRB

 

[Donald Bickers]

did you figure anything out yet

 

[HackitZ]

Yeah I'm off to bed long days right now. lots to get done at work before christmas.
Thanks, be back tomorrow night.

 

[Donald Bickers]

Yeah I'm off to bed long days right now. lots to get done at work before christmas.
Thanks, be back tomorrow night.

ok man,,,,have a good one

 

[HackitZ]

I figured out the issue, the center screw holding the one side of the coil had a piece of white plastic stuck in the middle of it. I removed the blockage and it now works. used it all day and it was way better than my kangertech.
I now have another issue, it came with 2 coils and i ruined one coil setting it up and getting it to work. so one coil in it and thats it until after the holidays when i have a little cash to stock up on supplies. no local stores sell any of the stuff to build your own mod.
so how long does a coil usually last with a silica wick?

 

[Donald Bickers]

the coil should last,if it gets burnt you can remove the silica and dry burn the coil to clean it and get a little more use out of it,then rewick it with regular cotton,(I like cotton better anyway)just be careful taking the old wick out

 

[chickenmonkey]

I have a coil in mine that has lasted over a month. Koh gen doh cotton is great for wicking the kayfun. Glad you have it all working?