X-Baby Q2
0.4Ω (40-80W)
Claimed best at 55-65W
Drip Tip:
18mm tall
16mm OD
14mm ID tapering to 8.5mm ID
Top :
21.65mm tall
24.5mm OD
22mm OD @ threading
Has 1 fill port measuring 7.8mm X 3.25mm
Chimney is 5.5mm ID
Dual air flow slots measuring 15mm X 1.8mm with full lock stops.
Glass:
24.5mm OD X 22.35mm tall
Base:
14mm tall
24.5mm OD
8mm deep
Since this is TOP airflow, there are no air slots in the base.
********************************************************************************************************************************************
The two sections below cover my normal testing procedure and preface.
I feel this is important information to include so you know what I do to ensure I test every one the same way.
It also provides you info on MY particular juice because it more than likely different than yours sol can/will have different results.
********************************************************************************************************************************************
Airflow wide open for both coil tests.
Before testing each coil I ensured proper saturation as well as break the coils in by starting at lower wattages and temps.
I vape at these lower wattages, slowly increasing and I vape though half to a full tank fill depending on what the coil needs.
Once the coils are properly broke in I start my tests.
For each wattage setting I took 10 casual pulls taking them as I felt the need.
Followed by 10 chain vape pulls to check for heat and flavor changes.
I Wait 5 minutes between each setting (allowing the coil to cool) to ensure I get the best the coils can produce.
After documenting all notes through this process I proceed to vape through 240ml of juice for each coil to check coil life.
********************************************************************************************************************************************
This may not seem news worthy to some but since high flavor percentages and really sweet juices kill coils, I check for it.
Mostly because I use 25% flavor of super sweet DIY juice and go through about 45ml per day.
My juice is a well known coil killer.
Generally I get only a few days out of coils so I'm always in search of the few that can last though my particular juice.
Clouds are clouds, I could care less.
Flavor on the other hand is where the importance to me is so that'll be my main objective.
********************************************************************************************************************************************
Coil:
X-Baby Q2
0.4Ω (40-80W)
Claimed best at 55-65W
30 - Plenty of vapor, no flavor.
35 - More vapor production, very little flavor increase.
40 - Still a bit more vapor, now starting to bring in some flavor.
45 - Flavor increase is pretty nice.
50 - Flavor is still growing but still not what I would call "full".
55 - Lot more vapor, flavor still rising. Great improvement.
60 - Really seeming like a Smok coil now, great flavor and vapor mix.
65 - Awesome flavor. Like when you first start chewing a piece of juicy fruit gum. Mouth watering.
70 - Vapor is ridiculously thick and flavor is absolutely full.
75 - No change from 70W, it may have capped out.
80 - Nope, there is little more life to this coil.
85 - Seems this is just a bit more than the coil can handle of my over flavored DIY juice.
Dropped it back down to 70W and enjoyed another 240ml of this greatness.
Coil:
X-Baby M2
0.25Ω (30-50W)
Claimed compatible with mech mods
A little more restrictive than I normally vape but not excessively tight.
20 - Ever so light of a flavor or vapor.
25 - Just a touch of increase in flavor, not much additional vapor.
30 - Vapor increased quite a bit but only a little added flavor.
35 - Slight flavor increase, nothing note worthy though.
40 - Now both the flavor and vapor are starting to wake up.
45 - Smooth and rounded out mix of flavor and vapor production.
50 - A really great mix of cool flavor and vapor that just seems to fill the desire.
55 - Wow, just as good as 50W but seems more full bodied while being just a touch warmer.
60 - A warm (not hot) vape that fills the room with clouds and tastes great.
65 - Just like 60W with more flavor.
Dropped it back down to 55W and enjoyed another 240ml of this greatness.
I have MANY Smok products and I can say the quality of this tank certainly gives me nothing to concern myself with when thinking of longevity of the tank.
This TFV8 X Baby is of high quality and durability.
How it looks on a few different mods:
Smok Alien
Laisimo L1
Smok G-Priv
Wismec Reuleaux 2/3
Laisimo Wyvern 235
Vaptio N1 Pro
Specs & Features
•4.0ml e-Liquid Capacity
•510 Threaded
•Diameter: 24.5mm
•Dimensions: 58.5mm x 24.5mm
•Large Central Airflow Chamber
•Large Dual Adjustable Airflow Slots
•Larger Heating Air Tube for Higher Airflow Efficiency
•Stainless Steel Construction
•Top Airflow Control Valve
•Top Fill Swivel Design with Large Fill Hole
•Wide Bore Delrin Drip Tip
What's Included:
•1 x Set of Spare Parts
•1 x SMOK TFV8 X-Baby Replacement Glass
•1 x SMOK TFV8 X-Baby Sub-Ohm Tank
•1 x SMOK V8 X-Baby M2 Core 0.25ohm Dual Coil Atomizer Head •30 to 50W
•1 x SMOK V8 X-Baby Q2 Core 0.4ohm Dual Coil Atomizer Head (Pre-installed) •40 to 80W (55 to 65W Recommended Range)
Manufacture link:
https://www.smoktech.com/atomizer/tfv8-x-baby
Manufacture pics and info:
Since the beginning of TFV series tank innovation we have been keeping trying to make a great top
airflow tank, now we succeeded, it is TFV8 X-Baby tank.
The success comes from repeated improvements and tests, the TFV8 X-Baby tank works like the world-wide famous babybeast tank, which brings massive clouds, rich flavor, smooth airflow, besides, it has a pleasant atomization sound
while vaping.
What's more, it has 4.0ml capacity, classical swivel top cap design and sealed leak-proof atomizer base, so we call it the baby beast brother and it will be a surprise member of TFV8 family.
Innovation keeps changing the vaping experience.
TFV8 X-BABY
SPECIFICATIONS
8 COLORS AVAILABLE
DELRIN DRIP TIP
The delrin drip tip will bring increased airflow and provide you with powerful draw effects.
