Become a Patron!

Profile RDA by Wotofo and Mrjustright1 review...Mesh done right?

mjag

Gold Contributor
Member For 4 Years
Youtube reviewer products are coming out at an alarming rate lately, some very good to great and some not so great. The Wotofo Profile RDA which was made in collaboration with Mrjustright1, a youtube reviewer is another offering. I have to admit I knew nothing about Mrjustright1 prior to receiving the Profile RDA directly from Wotofo for the purpose of this review, that has definitely changed now.

Main Features:

  • Flavor can be broken down layer upon layer
  • Break-through mesh style heating element
  • Easy to switch between mesh and wire coils
  • Spring-loaded ceramic support ensuring contact between mesh and cotton
  • 24mm sleeve with accurate air inflow
  • Experience from cool vape to warm vape
  • Up to 30 puffs at 75W before needing to re-saturate the wick when using pancake wicking method

Specs:

  • Size: 24*32.5mm
  • Material: SS + PEEK
  • Drip tip type: 810 drip tip
Ql7a9Gz.jpg


Mesh coil specs:

  • Coil resistance: 0.18ohm
  • Material: Kanthal A1
  • 16 x 6.8mm
  • Recommended wattage: 40-60W
7JhEbHP.jpg


Included in the package

  • Profile RDA
  • User Manual
  • 6mm Agleted Cotton Strip
  • Extra 810 Drip Tip
  • Bending Tool
  • 1 Clapton Coil
  • 2 Mesh Coil Sheets
  • Extra O'Rings & Screws
  • Phillips screwdriver
  • Squonk pin
  • Allen wrench

kHnSBIX.jpg


Getting to know the Profile RDA

I do not have too much experience with Mesh RDA's, the only one I tried was the Cthulu Ceto that I reviewed a while back and while you can get decent performance the hassle was not worth it for me. Having also tried a couple mesh RTA's in the past as well I just figured mesh was not for me, you can get it to work really well at times but it was just not for me in the long run.

Freemax helped to change the game when it comes to mesh with there Mesh subohm tanks, finally the potential for mesh as a coil began to make sense. They went even further and introduced the Mesh Pro and wow, the flavor that mesh can produce was intense to say the least.

Wotofo, in collaboration with YouTube reviewer Mrjustright1, may have just done for Mesh RDA's what Freemax was able to do with Mesh Subohm tanks, change the game.

The problem with Mesh is the wick needs to be tight to the mesh for it to work well and with repeated soakings in juice gravity tends to take over and contract the cotton thus ruining performance over time. Wotofo has solved that by using a ceramic block under the cotton with a spring to keep the cotton snug to the mesh, very smart. You can see the spring under the ceramic block on the bottom right.

L7BZvVY.jpg


The top cap and deck are notched to make it easy to line up the honeycomb style airflow which really lends to a smooth and quiet draw. That also helps when installing or removing the RDA so the top cap does not spin on the deck.

Good but not great o'ring tolerances on the deck, could hold on a little tighter for my tastes but just slightly. The Airflow o'ring is on the tight side but loosens up with a nice bead of juice, make sure and lube it up with ejuice before use and it is just about perfect.

Builds and Performance

Wotofo includes a ceramic bending tool, use the thick end to shape the mesh prior to installing.

BZ1zSm8.jpg


From there installation could not be simpler, one of the easiest installs your likely to have.

lbfuqHz.jpg


That was my first install and you can see I had a lot of cotton to deal with, turns out there is an easier way that Wotofo clued me into that I will address in my next build, don't do it like above.

The performance with the above build took a little getting used to as it is different, very good but different. There was a little break in for me but once that happened the flavor really surprised me and the cloud production was ridiculous. As you would normally expect from a mesh there was zero delay from when you clicked the fire button, instantaneous vapor, it heats up insanely quick. It is a dry vape for the most part, more moist when you just drip or squonk but the flavor just pops. Lasted a long time too, I got about 9 days and the mesh looked like it was good for more but I wanted to try a SS316L mesh I had lying around, here is what 9 days looks like.

YPkoPb2.jpg


I have 3 rolls of SS316L mesh, all from Vandy Vape but in different configurations, 150, 200 and 300 mesh. I used the mesh from the Profile RDA kit to cut the mesh into the same dimensions, 16 x 6.8mm. This time I decided to use Native Wicks Platinum Blend cotton so see the difference and used the cotton cutting technique Wotofo emailed me which works like a charm.

KFy9LnH.jpg


Of all 3 of the Vandy Vape SS316L mesh the 200 was my favorite, the flavor just popped, more so than any of the mesh I tried....sooo good. Didn't last as long as the Kanthal mesh though, this is what it looked like after 7 days which required a rebuild.

NR4RjXb.jpg


I did try the normal clapton Wotofo includes for a traditional build but that lasted a day and the next day I was back to the mesh, no contest, this RDA shines with mesh.

While different than a normal coiled RDA the flavor on the Profile RDA just pops, it really is that good. I also did not get that dreaded lava hot burn from hell that could be a problem with mesh RDA's and RTA's, when it was low you can taste a little bit of a dry hit enough to remember to drip or squonk. This thing chucks clouds too, surprising clouds at times as it is not as hot as you would suspect then just a plume of tasty clouds emerge from your mouth.


Squonking....yes please

I have not even dreamt of removing the squonk pin or using it any other way. Sure it drips fine and holds a decent amount of juice with the bushel of cotton you have stuffed in the 4mm juice well. The squonking action is just brilliant though, it comes up from the ceramic block just under the cotton and coil and saturates it beautifully. I ran it almost exclusively on a squonk mod and loved every minute, here are a few of the squonkers it called home.

wEICxoq.jpg


sMATbN0.jpg


I am going to buy a Gold Profile RDA for my Asmodus Pumper 21, love that combo but need a better matchy match.

Pros:

  • Outstanding flavor but different, more of a dry vape so some may not be as impressed
  • Super easy to build with the mesh but make sure and have sharp scissors to cut the cotton
  • Top cap is THICK and provides notches that line up with the deck to perfectly align your airflow
  • Airflow o'ring just right but you have to juice it up or it is too tight
  • 810 inner o'ring perfect, every 810 drip tip fits just fine
  • Sturdy phillips grub screws that work great with the flat head screwdriver I used
  • Smooth airflow that is pretty airy wide open, I ran it with the top air holes closed for a flavor boost
  • Mech coils last a good while, about 8 days or more is what I averaged
  • 2 very nice 810 drip tips included

Cons:

  • Takes a ton of cotton to work properly, need to make sure the wick is in tight
  • Not ideally suited for standard coils, once you try the mesh you won't want to use standard coils anyway
  • Dual deck o'rings do not hold on the top cap as securely as I would like

Final thoughts

I feel Wotofo and Mrjustright1 have just changed the game when it comes to Mesh RDA's, the Profile RDA is just that good. The included Kanthal mesh works great but the SS316L 200 mesh brought out even more performance but at a cost of rebuilding sooner.

The Profile RDA is an easy recommendation, just get 1 and enjoy. I hope Wotofo and Mrjustright1 have an RTA version in the works. I will buy one right away if they use the same ceramic clamping mechanism that keeps the cotton tight, very important for consistent performance.

I want to emphasize how important the ceramic block with spring is to keep the cotton tight. I had found with the other mesh RDA and RTA that I would have to go back in a compress the cotton after some use. This is what eventually made me say screw this, too much hassle. With mesh the cotton needs to be right up against it but at the same time you don't want to compress it so much it wicks like a brick. There is a fine line between just right and crap with the wick and the ceramic block with spring just make the process effortless.

The Profile RDA is available to buy directly from Wotofo here: https://www.wotofo.com/wotofo-profile-rda.html
Spare cotton here: https://www.wotofo.com/wotofo-agleted-organic-cotton-6.html
Spare mesh coils here: https://www.wotofo.com/mesh-style-coil-10pcs.html

Check out how this stacks up to other tasty gear and meet the Steampugs team of reviewers. Your bound to have a good time and read up on some great products, not so great ones too http://www.steampugs.co.uk/
 

mjag

Gold Contributor
Member For 4 Years
Good write-up. I've ordered two of them from 3FVape, but they're still trying to hire the rowers for the boat. I've never used mesh before and I'm interested in where do you get the SS mesh from?

Ugh, I know the pain of China orders, they finally found a rower for my order I placed more than a week ago. 3Fvape used to carry the mesh but it is listed as sold out there now. Slowtech has it though: https://www.fasttech.com/p/8774700 and for that price I will probably order another roll myself. Thanks for checking out my review bobnat.

Thank you @Heartsdelight :hug: Mesh is still different enough that I am sure there are some who may not prefer it, especially those who prefer a more wet or rowdy vape. Took me a day or 2 to get used to it and the SS316L 200 mesh took it to another level for me, some may prefer the Kanthal though, they are different enough. What really made it really work for me is just the consistency of the vape from day 1 to day 7, not something I experienced with the other mesh RDA I reviewed.
 

bobnat

VU Donator
Gold Contributor
Member For 4 Years
Finally got my two from China, a SS and a gold one (WTF?). Got one up and running on my VT Inbox.

First off, the amount of cotton is staggering. I need a barber to trim it all. There is definitely a learning curve involved in trimming this much cotton but so far it’s working. I’m vaping one of my all time favorites, 3 fruits with marshmallow at 5.5% flavoring, so I know what this should taste like. The flavor is as good as I’ve ever tasted for this juice. I’ve got the AF at 1/3 and it is smooth and quiet. It’s my first time using mesh so I don’t have bad experiences or prejudgments about it. I never use Kanthal either, but I don’t notice any off taste at all. I did order some SS mesh though based on Mjag’s suggestion.

Building the coil was the easiest I've ever done. I struggle with coils sometimes and it's a pleasure to build on this. It took about 20 seconds max. The mesh reads at precisely 1.8 ohm as stated.

The only negative I have with it is the driptip. I also don’t use wide ones, in fact I’m quite particular in the type I use, however I can get used to it. It’s the height that’s off putting as I can feel the heat. It’s a nice looking drip tip, but it just won’t do. Fortunately, I’ve got a handful of taller ones from various RDAs I’ve bought and I found one I like.

I’m quite pleased with this and I’m glad I got two of them. I’ll have to get at least another, preferably gunmetal. These can easily become my daily RDAs and replace my Hadalys and Entheons, which do leak a bit if one is not careful.

Thanks for the review, Mjag. Between you and Pugsley you guys did a great job on this rda.
 

mjag

Gold Contributor
Member For 4 Years
That is awesome to hear @bobnat :cheers:

I gotta catch up and order another but still not sure what color, thinking gold like you got, how is the finish on the gold?
 

bobnat

VU Donator
Gold Contributor
Member For 4 Years
That is awesome to hear @bobnat :cheers:

I gotta catch up and order another but still not sure what color, thinking gold like you got, how is the finish on the gold?

I think it's well done as it certainly looks vivid but not overly polished to the point of being obnoxiously bright. But we won't know for awhile. I've got nothing that'll match it though.
 

mjag

Gold Contributor
Member For 4 Years
I think it's well done as it certainly looks vivid but not overly polished to the point of being obnoxiously bright. But we won't know for awhile. I've got nothing that'll match it though.
I got the Asmodus pumper 21, love that squonker and it needs a gold RDA. Been using the Asmodus C4 on it but need another profile on there, loved the combo.

Thanks for the feedback

Sent from my SM-N950U using Tapatalk
 

MWorthington

Silver Contributor
Member For 4 Years
ECF Refugee
Good job, mjag. I think I'd like this rda because I really prefer a cooler, less saturated vape. My main atty, the medusa reborn, is so wet I'm constantly having to wipe condensation off my upper lip after exhaling. A little aggravating but it's sooo good! :)
 

mjag

Gold Contributor
Member For 4 Years
Stopped by a local vape shop and when I asked what the hot new product is? they said the Profile RDA. Had to pick up the gold to go with my Asmodus Pumper 21, love the combo.
6d68c5cfe9d78c6e0365692cf8d13917.jpg


Sent from my SM-N950U using Tapatalk
 

bobnat

VU Donator
Gold Contributor
Member For 4 Years
Stopped by a local vape shop and when I asked what the hot new product is? they said the Profile RDA. Had to pick up the gold to go with my Asmodus Pumper 21, love the combo.
6d68c5cfe9d78c6e0365692cf8d13917.jpg


Sent from my SM-N950U using Tapatalk

That does look like a good combo. I might have to let my wife work on my color schemes for a bit.
 

mjag

Gold Contributor
Member For 4 Years
That does look like a good combo. I might have to let my wife work on my color schemes for a bit.
Just as long as u don't wind up with pink, my lady would be all over purple for some reason

Sent from my SM-N950U using Tapatalk
 

VU Sponsors

Top