Become a Patron!

SPARE PARTS - O-rings, Screws, Build Decks, Chambers. Need something? Ask Here!

Ms. Trixy

VU Donator
Platinum Contributor
ECF Refugee
Member For 5 Years
Reddit Exile
VU Patreon
! SPARE PARTS !
Haves & Needs
Use the following to keep things simple:

I HAVE or I NEED
I HAVE:
O-rings:
Black - ID: 6.4 - OD: 7.8 - 1.0mm thick
Black - ID: 8.0. - OD: 10.0 - 1.0mm thick
Black - ID: 20.0 - OD: 23.5 - 2.0mm thick
Black - ID: 5.0 - OD: - 7.7 - 1.8 mm thick
 
Last edited:

Deucesjack

VU Donator
Platinum Contributor
Member For 4 Years
ECF Refugee
I thought this thread could be useful for those of us that misplace, ruin, lose
or just can't
find those rare spare parts anymore.

I need the thin o-ring for an original WOTOFO Serpent that sits at the base of the bell cap housing.
I accidentally cut the bell cap o-ring before lubing it and the cap keeps sliding up, nearly closing my airflow.
I looked at my other my o-rings and they're either too big or too thick. 22.mm and the o-ring is maybe 1-2mm.The one that came with it is really very thin and Wotofo doesn't provide that extra o-ring.

I hope one of you can help me out. I'll pay pay for the stamp, of course.
If you want I can send you the whole base. I broke the glass on mine so it's useless to me.

Sent from my SAMSUNG-SM-G900A using Tapatalk
 

Ms. Trixy

VU Donator
Platinum Contributor
ECF Refugee
Member For 5 Years
Reddit Exile
VU Patreon
Oh, Deuces that would be wonderful! Did you find that your bell cap kept riding up? PM incoming.
 

Deucesjack

VU Donator
Platinum Contributor
Member For 4 Years
ECF Refugee
Oh, Deuces that would be wonderful! Did you find that your bell cap kept riding up? PM incoming.
Tbh, I didn't have it long enough. I broke the glass before I got through the first tank. Lmfao. The few pulls I got off it I did enjoy. It's the tank that started me on my single coil journey. I'll dig it out out and find the spare parts bag too. You can have that as well.

Sent from my SAMSUNG-SM-G900A using Tapatalk
 

Ms. Trixy

VU Donator
Platinum Contributor
ECF Refugee
Member For 5 Years
Reddit Exile
VU Patreon
Thanks Deuces for sending me a spare build deck.

I need the airflow/juice port that the top bell cap slides onto and should snap in place. Mine keeps riding up, nearly closing off my airflow.

Does anyone have that part as a spare? I have a feeling Wotofo milled my top cap a cm too tight. So, either the bell cap or mid juice port and airflow section is what I would like. I really like the Serpent. If worse comes to worse, I'll get one at GearBest for $20. Ugh!
 

Ms. Trixy

VU Donator
Platinum Contributor
ECF Refugee
Member For 5 Years
Reddit Exile
VU Patreon
Original Wotofo Serpent:
Does anyone have either the top bell cap or the middle juice port and airflow chamber hanging around somewhere?
 

Paratech

I forgot
VU Donator
Gold Contributor
Member For 4 Years
Are you talking about THIS serpent?
https://www.vaporworld.biz/clearance/wotofo-serpent-rta-stainless/


I think I am the only person that purchased a CCI Triforce Tank (30mm)
Cloud Chasers Inc isn't really busting at the seams so there aren't many out there.
The top cap (reverse threaded) on mine is stripped.
Been looking for quite some time but never seemed to have any luck finding just the top cap.
Found the 22mm one many times, just not the 30mm.
For more than $50 I've found the tank a few times but can't say it is good enough for that price.
Can't believe that after a year of looking I found it here for $4.99:
https://cjvapors.com/products/cci-triforce-replacement-delrin-tip?variant=16860433860
 

deathpriest

Member For 2 Years
O-rings, the manufacturer should come up with refurbishment kits! maybe there are out there but, I have not found them yet. I am wondering if a Homedepot o-ring kit would work. Maybe a shop owner can chip in, what they get and where.
 

Paratech

I forgot
VU Donator
Gold Contributor
Member For 4 Years
Sorry. Didn't see your question, Paratech. Here's the one I need help with:
View attachment 86383

The entire top bell cap comes off. Mine won't stay put. Keeps riding up and closes my airflow.
Bummer, I asked about that specific one because I have it and would have sent it to you.
Sorry I couldn't help.
 

Ms. Trixy

VU Donator
Platinum Contributor
ECF Refugee
Member For 5 Years
Reddit Exile
VU Patreon
I wrote to Wotofo about the RTA and availability of any replacement parts. We'll see.
 

Hype

Bronze Contributor
Member For 4 Years
Anyone have a non leaking deck for a Kylin . The finish is not important . I will gladly pay shipping .
 

Ms. Trixy

VU Donator
Platinum Contributor
ECF Refugee
Member For 5 Years
Reddit Exile
VU Patreon
Got the Kylin Mini...no help here.

Replacement Wraith RSA Bottles - Set: 1 black/1 clear = $7.95 Auth. COV
 

Ms. Trixy

VU Donator
Platinum Contributor
ECF Refugee
Member For 5 Years
Reddit Exile
VU Patreon
Here's the one I need help with:
View attachment 86383
The entire top bell cap comes off. Mine won't stay put. Keeps riding up and closes my airflow.

SOLVED: It's the o-ring that's making the cap roll up. Now I just put the cap on to the right of the airflow and twist it to the opening. It now stays in place. I'm glad the Serpent comes with extra o-rings though.
 
Last edited:

Ms. Trixy

VU Donator
Platinum Contributor
ECF Refugee
Member For 5 Years
Reddit Exile
VU Patreon
I NEED:
Clieto: Silicone flat ring that is around the drip tip stub. They don't provide an extra. This will be a hard one. I can't find flat rings anywhere.
 
Last edited:

Ms. Trixy

VU Donator
Platinum Contributor
ECF Refugee
Member For 5 Years
Reddit Exile
VU Patreon
I NEED:

*Aspire Clieto:
I'm still looking for that flat ring around the drip tip section. Since those are apparently hard to find, Aspire should add 2 to each extras bag. I'll check their website. Ugh!

MEMBER HELPED
Tobeco Super Tank Mini: I need the bottom o-ring that seats the glass. The L shaped seal has halfway melded right onto the glass. I tore it trying to get it off while cleaning it.
 
Last edited:

Pastorfuzz

Gold Contributor
Member For 4 Years
VU Patreon
Aspire Clieto (not 120): I'm still looking for that flat ring around the tip section. Since those are apparently hard to find, Aspire should add 2 to each extras bag. I'll check their website. Ugh!

Tobeco Super Tank Mini: I need the bottom o-ring that seats the glass. The L shaped seal has halfway melded right onto the glass. I tore it trying to get it off while cleaning it.

Will of course pay shipping.
Trixy, I don't have a Clieto or the Tobeco or measurements for them to compare but I have these.oring 003.JPG oring 001.JPG oring 008.JPG oring 009.JPG
Is this what you need?
 
Last edited:

Ms. Trixy

VU Donator
Platinum Contributor
ECF Refugee
Member For 5 Years
Reddit Exile
VU Patreon
Oh, that's' wonderful! I'm grateful for your time looking!
I wanted to measure it hopefully out of the glass, and it just popped out. Odd, considering it was melded before. Maybe my attempt at trying to fill it again has loosened it. It's discolored and I can still see some damage to the o-ring. I believe it just shrunk since it leaked profusely.

RESOLVED
Tobeco:

The measurements are pretty close - OD: 21.0 - ID: 16.7 - H: 3.8 (all +/- .1) The ID inside the tank bottom is 21.5mm.
I believe the ID may be due to it being old and pushed into that area for so long?
But yes. A seated ring is what I'm in need of. I would certainly like to try that one
.

Today I'll look at what I have open to see if o-ring replacement is going to be an issue.
I don't have many tanks/atties opened, but I'll check their respective bag of goodies.
 
Last edited:

Pastorfuzz

Gold Contributor
Member For 4 Years
VU Patreon
Send me your address and i'll get some sent in the mail tomorrow.
I'll send some others also.
Can't help with that Clieto though. Don't have anything like you described
 
Last edited:

Ms. Trixy

VU Donator
Platinum Contributor
ECF Refugee
Member For 5 Years
Reddit Exile
VU Patreon
looking for a 510 drip tip adapter for an avocado 24 in SS

Sorry Elis_pr. I have the black on and I'm using the 510 adapter.

This is a great idea

Perhaps this should be a Sticky? We would have more participation and Spare Parts! Everyone has/needs parts.
I think it should go in the Vaping Related but doesn't fit in any category?
@Countrypami
 

Ms. Trixy

VU Donator
Platinum Contributor
ECF Refugee
Member For 5 Years
Reddit Exile
VU Patreon
I'm looking for a 24mm Twisted Messes sleeve and top cap. I bought just the base for a vape comp and didn't want to spend $60 for the full RDA.
Anyone got Twisted Messes parts collecting dust?
 

wildgypsy70

“Widgy Pidgy”
Staff member
Senior Moderator
VU Donator
Platinum Contributor
VU Challenge Team
Member For 5 Years
VU Patreon
Sorry Elis_pr. I have the black on and I'm using the 510 adapter.



Perhaps this should be a Sticky? We would have more participation and Spare Parts! Everyone has/needs parts.
I think it should go in the Vaping Related but doesn't fit in any category?
@Countrypami
I like this idea! A spare parts sticky!
 

Ms. Trixy

VU Donator
Platinum Contributor
ECF Refugee
Member For 5 Years
Reddit Exile
VU Patreon
I NEED:

Aspire Clieto:
I'm still looking for that flat ring around the drip tip section. Since those are apparently hard to find, Aspire should add 2 to each extras bag.

Twisted Messes:
I'm looking for a 24mm Twisted Messes sleeve and top cap. I bought just the base for a vape comp and didn't want to spend $60 for the full RDA.
Anyone got Twisted Messes parts collecting dust? I had a bunch of 24mm RDAs I sold last year. :facepalm:
 

Opfor82nd

Member For 1 Year
I have a Serpent SMM with Allen screws for the deck and would like to switch them out with Phillips screws. Does anyone know where I may be able to find these or at least the size that I could search.
Also my my friend has a Zeus Dual RTA with Allen screws and would like to switch these out with Phillips screws as well. Unfortunately been online and the factory site and can’t find the size of the deck screws.
 

VAPEROXX

Gold Contributor
Member For 4 Years
Unlisted Vendor
Need a bubble glass for the Augvape Intake RTA by Mike Vapes. Please PM if you have an extra laying around. Thanks!

Sent from my SM-G965U using Tapatalk
 

Ms. Trixy

VU Donator
Platinum Contributor
ECF Refugee
Member For 5 Years
Reddit Exile
VU Patreon
I need a squonk 510 pin for my coppervape NarDA
I have an extra squonk 510 pin for the Entheon or Hadaly

What's the difference? You guys drive me nutz with all of your cool hardware. OD, length? I have a few attys.
 

mcmillonronald

Member For 4 Years
Hello group, i have 2 Hanya rta's and i need glass tank sections for both of them they are my wife's favorite tanks does anyone have the dimensions of the tank or know how i can get replacement glass for the two I've checked Fasttech and they dont have a listing for this glass if i knew the dimensions i could probably find a match, thanks in advance Big love to everyone.

Sent from my SM-S737TL using Tapatalk
 

Ms. Trixy

VU Donator
Platinum Contributor
ECF Refugee
Member For 5 Years
Reddit Exile
VU Patreon
I suggest posting a "trade" for the glass in the Trading Post thread. You never know.


BUMP for post #30
 

twan013

Bronze Contributor
Member For 2 Years
I know this is more focused on RDA/rta spare parts but can I ask if anyone can spare a 20700 battery wrap and possibly an insulator? I shorted one of my ampkings last night (torn wrap) and I don't know if I can still use it or if I need to retire it (please advise). My other one is still good but the wrap is even worse on it. Thanks in advance!

Sent from my SM-G955U using Tapatalk
 

gsmit1

Platinum Contributor
Member For 4 Years
This is probably a long shot, but does anybody know of a squonk capable 510 pin for the MGNT v1.5 RDA?
 

MyMagicMist

Diamond Contributor
ECF Refugee
Member For 5 Years
This is a great idea

*cough, ahem* I'll nominate a vote to sticky this thread and maybe dub it Ms Trixy's PIF Junk Drawer, or as the good lady Ms. Trixy so declares to call it. At any given I think it needs stickied and kept open with access for all members, follow basic PIF rules.

Let vapers help vapers keep vaping. Ha! We are the Vaping Templars. --- No, please don't anyone draw the connection of Morely to Jacques Molay last know Grand Master of the Templars. I will deny being the grand King James, the eternal Green Man/Jack O the Green too. Nope, no idea what traveling in time is, not the slieghtest clue, not me,
 
Last edited:

heateris

Bronze Contributor
Member For 4 Years
I’m looking for a couple things-

OBS Engine rta or Nano o-rings

Dead rabbit RTA Drip tip

Let me know...


Sent from my iPhone using Tapatalk
 

Bigrick

Gold Contributor
Member For 4 Years
ECF Refugee
Gub screws for a serpent mini with allen if possible also grubs for DR also with allen...
 

VU Sponsors

Top