Become a Patron!

Aspire Atlantis coil-fits

KingNaga

Member For 4 Years
Ok. It might be the o-ring around the thread is bigger on those specific Atlantis coils. Try using the o-ring off one of your old Triton coils. Also push the pin in as far as it'll go before inserting the new coil. It might help no atomizer errors.

Sent from my Nexus 6 using Tapatalk
 

KingNaga

Member For 4 Years
Triton 1/2 coils are the same as Atlantis. You could always try another coil to see if it acts the same.

Sent from my Nexus 6 using Tapatalk
 

georgemeadal

Gold Contributor
Member For 4 Years
Sure, here it is.
Thanks, that is an Atlantis v2 coil with 4 air holes in the positive pin vs two for V1. That coil should fit perfectly in the Triton tank. Take the coil out completely and screw the base and tank portion together, does it screw in all the way ? The only other thing I can think of is to check that the coil is screwed completely in to the base (add a pic of it screwed in if you can) and also check the chimney area for any obstructions that would prevent the top of the coil from seating all the way.
 

chuckpie85

Bronze Contributor
Member For 4 Years
ECF Refugee
I had the same problem. The o ring on the base of the tank is too large and will not allow you to screw the base in fully. Had the same exact issue with one of my triton v1s. I was not able to locate an oring that was ever the correct size. I just ordered a replacement base for it. There were a couple vendors that had them relatively cheap. If you do not have any luck let me know and I'll see if I can find one of bases since I don't use my Triton's any longer.
 

theboysplusme

Member For 4 Years
Member For 3 Years
Thanks, that is an Atlantis v2 coil with 4 air holes in the positive pin vs two for V1. That coil should fit perfectly in the Triton tank. Take the coil out completely and screw the base and tank portion together, does it screw in all the way ? The only other thing I can think of is to check that the coil is screwed completely in to the base (add a pic of it screwed in if you can) and also check the chimney area for any obstructions that would prevent the top of the coil from seating all the way.


The tank and base fit together perfectly until I install the coil. When screwing the coil into the base, it will only turn one full turn before stopping. That being said, I don't think it will fulling screw in.. blah. Here's a picture of it:
 

Attachments

  • IMG_0390.JPG
    IMG_0390.JPG
    1 MB · Views: 34

theboysplusme

Member For 4 Years
Member For 3 Years
I had the same problem. The o ring on the base of the tank is too large and will not allow you to screw the base in fully. Had the same exact issue with one of my triton v1s. I was not able to locate an oring that was ever the correct size. I just ordered a replacement base for it. There were a couple vendors that had them relatively cheap. If you do not have any luck let me know and I'll see if I can find one of bases since I don't use my Triton's any longer.


Awesome, I appreciate that. So, what kind of base am I looking for? Atlantis or Triton?
 

chuckpie85

Bronze Contributor
Member For 4 Years
ECF Refugee
That black o ring on the base closest to the coil will give issues screwing it all the way down when a coil is installed. When no coil was installed on mine the larger one right was able to collapse enough to fully install the base but once a coil was there the resistance was to great. I'm fairly certain that's issue. Icant seem to find my Tritons at the moment but the ring looks too big on yours.
 

theboysplusme

Member For 4 Years
Member For 3 Years
Oh, I see.. gotcha. Mine works fine with the Triton coils, it's just the Atlantis ones that won't seem to fully screw in. Idk..

Thanks for your help :)
 

georgemeadal

Gold Contributor
Member For 4 Years
The tank and base fit together perfectly until I install the coil. When screwing the coil into the base, it will only turn one full turn before stopping. That being said, I don't think it will fulling screw in.. blah. Here's a picture of it:
Good morning!...time to go to work. I can see by looking at that picture that your coil doesn't screw fully into the base. It should* screw in a few more turns until the clear o-ring is seated firmly against the base. I'm not sure why that's happening, have you tried more than one new coil?
 

Whiskey

Diamond Contributor
Member For 4 Years
Pretty sure they will fit in the Billet box rev4 as well, as soon as I get the mod I will try it and report back
 

Whiskey

Diamond Contributor
Member For 4 Years
Pretty sure they will fit in the Billet box rev4 as well, as soon as I get the mod I will try it and report back
Fits :)
Another question, what other coils besides the melloIII coils fit the Eleaf IJustX , anyone know?
 

5150sick

Under Ground Hustler
Staff member
VU Administrator
Senior Moderator
VU Donator
Diamond Contributor
Press Corps
Member For 5 Years
Mod Team Leader
Wouldn't it be nice if they all just developed an industry wide standard threading and just stuck with it?

Maybe a small. medium. and, large type of thing for the different widths between the pen style all the way up to the smok beast?
 

Angrygod50

Gold Contributor
Member For 4 Years
Member For 3 Years
Member For 2 Years
Fits :)
Another question, what other coils besides the melloIII coils fit the Eleaf IJustX , anyone know?
Any of the Atlantis/Triton style coils will fit. I use the Aspire EVO Clapton's in my Melo. The first post is a big list of tanks that take the same coils if you wanted to try some other brands.
 

Countrypami

The Link Ninja
Staff member
VU Administrator
Senior Moderator
VU Vendor Employee
VU Donator
Diamond Contributor
ECF Refugee
VU Live Host
Member For 5 Years
Reddit Exile
VU Patreon
Has anyone tried the Atlantis coil in the Sense Blazer Mini?
 

georgemeadal

Gold Contributor
Member For 4 Years
Has anyone tried the Atlantis coil in the Sense Blazer Mini?
I have not BUT they do not look like an Atlantis style. They look more like Herkales Plus coils:
atlantis_coils_occ_0.5ohm_1ohm.png


herakles-coil-3_1.jpg

f2d6e0a5b19725135fef94909a38b804.jpg
5fc6258b07e5e172f9bffe13374b6e01.jpg


Sent from my VS985 4G using Tapatalk
 
Last edited:

Countrypami

The Link Ninja
Staff member
VU Administrator
Senior Moderator
VU Vendor Employee
VU Donator
Diamond Contributor
ECF Refugee
VU Live Host
Member For 5 Years
Reddit Exile
VU Patreon
I have not BUT they do not look like an Atlantis style. They look more like Herkales Plus coils:
f2d6e0a5b19725135fef94909a38b804.jpg
5fc6258b07e5e172f9bffe13374b6e01.jpg


Sent from my VS985 4G using Tapatalk
Hopefully someone has one and can test it out for me. I'm thinking about getting a Blazer mini but only if I can use my Atlantis coils in it.
 

georgemeadal

Gold Contributor
Member For 4 Years
Hopefully someone has one and can test it out for me. I'm thinking about getting a Blazer mini but only if I can use my Atlantis coils in it.
edited my post above to show the Atlantis coils too.
As you can see, the top two pictures are "Atlantis Style" the bottom two are the shorter "Herkales Plus" style which are a good bit shorter.
Check out this review (jump to 7:40) for more insight.
and this one (jump to 6:20)
 
Last edited:

Countrypami

The Link Ninja
Staff member
VU Administrator
Senior Moderator
VU Vendor Employee
VU Donator
Diamond Contributor
ECF Refugee
VU Live Host
Member For 5 Years
Reddit Exile
VU Patreon
edited my post above to show the Atlantis coils too.
As you can see, the top two pictures are "Atlantis Style" the bottom two are the shorter "Herkales Plus" style which are a good bit shorter.
Check out this review (jump to 7:40) for more insight.
and this one (jump to 6:20)
Thanks. I'll check those out. :)
 

georgemeadal

Gold Contributor
Member For 4 Years
Just wanted to say thanks for posting this list ..imensly useful . also when you state Eleaf Melo lll Mini - top threads not used
You just put it in the tank like normal?
Meaning, the top threads of the coil are not used to hold the tank together. Some tanks use the top and bottom threads of the coil to hold the tank top and base together. Hope I explained that well lol...

Sent from my VS985 4G using Tapatalk
 

Charmz4him

Member For 2 Years
Member For 1 Year
Meaning, the top threads of the coil are not used to hold the tank together. Some tanks use the top and bottom threads of the coil to hold the tank top and base together. Hope I explained that well lol...

Sent from my VS985 4G using Tapatalk

Thanks again
 

SpectoVia

VU Donator
Silver Contributor
Member For 4 Years
VU SWAT
IMG_0372.JPG

Success! The Vaporesso EUC with the adapter works in my Amigo tank.

Kudos to George M. for his yeoman's work with the tank/coil compatibility lists. It's been a great resource for me.
 

EZGOER

Member For 2 Years
Member For 1 Year
Hello. Just wanted to say this is a great list and is very helpful. I purchased a Geek Vape Illusion Mini tank, which is on your list, just because it is compatible with so many different coils. It will use these Atlantis style coils with the included base adapter, and it will also use the bigger Smok Baby Beast and Big Baby Beast coils without the adapter. I will say I have used several of these coils in this tank, some work better than others. i really like the Aspire Clapton and EVO coils, also the Amigo Riptide coils. I think the tank design prevents some of these coils from working like they should. The Atlantis style coils, once screwed into the base and then into tank are housed in a chamber like space inside the tank, maybe preventing some of the coils from wicking properly. I would have to say that this is the best tank I own, great flavor, big clouds and very many coil combinations, anywhere from low wattage MTL vaping to 150 watts and above.
 

Just Frank

Platinum Contributor
Member For 4 Years
I was looking at the Digiflavor Bucho. The coils it uses look very similar to the Atlantis style, but I don't see it on the list. Can anybody enlighten me about the Bucho tank?
 

Countrypami

The Link Ninja
Staff member
VU Administrator
Senior Moderator
VU Vendor Employee
VU Donator
Diamond Contributor
ECF Refugee
VU Live Host
Member For 5 Years
Reddit Exile
VU Patreon
Has anybody tested Atlantis coils in the Melo 4 yet? Do they work??
 

SpectoVia

VU Donator
Silver Contributor
Member For 4 Years
VU SWAT
My venture into Atlantis/Amigo coils in a Melo 4 D25 was a rather messy affair.
After attaching the coil base to the tank assembly and tightening, I was still able to rotate the glass tank which led to some leaking.
 

Countrypami

The Link Ninja
Staff member
VU Administrator
Senior Moderator
VU Vendor Employee
VU Donator
Diamond Contributor
ECF Refugee
VU Live Host
Member For 5 Years
Reddit Exile
VU Patreon
My venture into Atlantis/Amigo coils in a Melo 4 D25 was a rather messy affair.
After attaching the coil base to the tank assembly and tightening, I was still able to rotate the glass tank which led to some leaking.
Mine's the 22, wonder if that would make a difference? But it's good to know they do fit, thank you! :)
 

SpectoVia

VU Donator
Silver Contributor
Member For 4 Years
VU SWAT
That’s what you got from that? lol

Sorry, I should have been clearer. I don’t think they fit. I wouldn’t recommend.
I also should have mentioned that I was using an Amigo factory coil.
And, I should have used the word “spin” as opposed to “rotate”. Better description of how freely the glass moves with the tank fully tightened together.

But your right about the point that the D22 might be a better fit.
 

Countrypami

The Link Ninja
Staff member
VU Administrator
Senior Moderator
VU Vendor Employee
VU Donator
Diamond Contributor
ECF Refugee
VU Live Host
Member For 5 Years
Reddit Exile
VU Patreon
That’s what you got from that? lol

Sorry, I should have been clearer. I don’t think they fit. I wouldn’t recommend.
I also should have mentioned that I was using an Amigo factory coil.
And, I should have used the word “spin” as opposed to “rotate”. Better description of how freely the glass moves with the tank fully tightened together.

But your right about the point that the D22 might be a better fit.
Oh, Ooops!... I thought you were saying you had it in there and was using it but came across the leaking issue. Thanks for the clarification.
 

Countrypami

The Link Ninja
Staff member
VU Administrator
Senior Moderator
VU Vendor Employee
VU Donator
Diamond Contributor
ECF Refugee
VU Live Host
Member For 5 Years
Reddit Exile
VU Patreon
Atlantis/Triton coils will fit the Melo 4 that you've got just fine. Most, but not all, of eLeaf's iJust and Melo tanks can be used with Atlantis/Triton coils.

I hope this helps.
Great, thanks! :)
 
I'm new to vaping I have 3 tanks and looking to find out which coils are compatible with the following tanks

#1- tobeco super mini (25mm I believe)
#2- iJoy Captain tank (it came with my iJoy captain PD1865 mod)
#3-melo 4 tank
If you can tell me which coils are compatible with the tanks I have listed above that would be wonderful thank you.
** When replying please put which tank is compatible with which coils please**
 
Last edited:

shawn.hoefer

Gold Contributor
Member For 4 Years
The Tobeco and the Melo will both use Atlantis style coils. The Captain is not compatible with anything else that I can find.
 

shawn.hoefer

Gold Contributor
Member For 4 Years
I understand that , so all the Atlantis coils are the same size ( not talking about the ohms)
The parts that matter where installation is concerned... The threads top and bottom, and the positive contact... Are the same. The innards (wicking, wire) are different. Some compatible coils are gold, some silver (might be stainless, might be chromed brass).
 

SpectoVia

VU Donator
Silver Contributor
Member For 4 Years
VU SWAT
I can't explain why it took me a year to post this atomizer that uses these coils.
Probably because I rarely see it anywhere anymore. But just in case anybody might wonder......

Ladies and gentlemen,
I present to you, the runt of the Tobeco Super Tank Family.
The Nano.
2258D467-58CA-4649-B3F3-65B417B66826.jpeg

2 mls and uses the same kind of drip tip as the other Tobeco tanks.
A perfect fit with a CoV Mini Volt.
(hat tip to @Ms. Trixy for a great deal on the mod)
 

Ms. Trixy

VU Donator
Platinum Contributor
ECF Refugee
Member For 5 Years
Reddit Exile
VU Patreon
I can't explain why it took me a year to post this atomizer that uses these coils.
Probably because I rarely see it anywhere anymore. But just in case anybody might wonder......

Ladies and gentlemen,
I present to you, the runt of the Tobeco Super Tank Family.
The Nano.
View attachment 130862

2 mls and uses the same kind of drip tip as the other Tobeco tanks.
A perfect fit with a CoV Mini Volt.
(hat tip to @Ms. Trixy for a great deal on the mod)


Wow! That really is nice. I'm glad you are enjoying your Mini Volt.
 

SpectoVia

VU Donator
Silver Contributor
Member For 4 Years
VU SWAT
another one for the list @georgemeadal
Saw this tank at Everzon.com for $2.50, (and really cheap at other vaping sites) thought it looked like one for the list, and took a shot

5A5C1F98-9E37-44CB-85F1-C5EA69F932B6.jpeg

p.s. @Just Frank .....I know it's been a while since your previous query, but I hope this helps
 

VU Sponsors

Top