The Geekvape Ammit MTL RDA was supplied by Geekvape for this review
From geekvape site -
The Ammit RDA is a compact MTL RDA that features three-dimensional airflow system transferring air from top to bottom producing unbeatable flavor while retaining leak-proof capability. 12 airflow adjustment options providing the most variable restrictions for different preferences.
GeekVape Ammit MTL RDA Main Features
3D airflow transferring from top to bottom
* Leak-proof design with top to bottom airflow system
* Surround airflow design delivering from three different directions directly at the coils producing unbeatable flavor
The geekvape Ammit MTL RDA comes in a clam shell case, with the ammit on full display
Once opened, on the left is the ammit, on the right is your spares and accessories, including tools for building, spare orings, spare screws, squonk 510 pin, air reducer, extra drip tip, coils and on the bottom is the info paperwork and instructions.
The ammit claims to be leak proof, I can't stand having my hands and mod covered in juice, so glad to see geekvape go with this design, I've had zero leaking and I do tend to over squonk (did only use ammit RDA in squonk setup), the airflow holes are on the top part of the RDA, with the air flow going between the chamber and outer wall, it is then lead to 2 holes at the bottom which then reaches the deck from 3 holes, one either side of the coil and one underneath it, there is also a airflow insert under the coil and geekvape supply a 2nd smaller one, they are tiny and a little tricky to work with as so small though.
The airflow on the top cap has a good range from a very tight MTL to a restricted DL, there is 5 hole selections, from 2mm to 0.8mm, and can either use single selection for a hole or multiple holes. Personally I like a semi tight MTL draw and been using single selection on the 1.5mm hole
I used one of clapton coils that comes with the ammit, found building on the ammit simple enough with the 2 post deck. I made sure to position the coil low enough so got hit in the center by the side airflow holes. The coil came out to 0.68ohms, I do normally use clapton coils even for MTL vape, but normally mine are around the 1.5ohm range, but still really liked the supplied coil, and gave a good vape experience.
Being a RDA, wicking is simple enough, I just made sure no cotton was touching the airflow holes on the deck area.
And we are ready to vape
Out of all the newer MTL squonk RDA's I have tried recently, without a doubt the ammit MTL RDA is the best for me, it gives great flavor with smooth airflow, it is easy to build on and I love the airflow design, it is easy to adjust and don't have to worry too much about leaking, I will say I do not like the center airflow insert that can be changed out, it is so small, found tricky to get the other one seated in to the RDA, sure would be easy to lose when changing it out, but once it is changed, really never have to bother with it again.
I like the selection of drip tips, you get a larger metal drip tip, but also a delrin one with a 2nd tip for it, one being 2mm inside, the other 3mm, I liked the 2mm as was also a little longer which I prefer.
I highly recommend the Ammit MTL RDA if into squonking and are a MTL vapor, you won't be disappointed, and I give it a rating of 9.5/10, yes it is that good
Thank you for geekvape supplying the Ammit MTL RDA for this review and if you do want to try it, can purchase from their store HERE
From geekvape site -
The Ammit RDA is a compact MTL RDA that features three-dimensional airflow system transferring air from top to bottom producing unbeatable flavor while retaining leak-proof capability. 12 airflow adjustment options providing the most variable restrictions for different preferences.
GeekVape Ammit MTL RDA Main Features
3D airflow transferring from top to bottom
* Leak-proof design with top to bottom airflow system
* Surround airflow design delivering from three different directions directly at the coils producing unbeatable flavor
The geekvape Ammit MTL RDA comes in a clam shell case, with the ammit on full display
Once opened, on the left is the ammit, on the right is your spares and accessories, including tools for building, spare orings, spare screws, squonk 510 pin, air reducer, extra drip tip, coils and on the bottom is the info paperwork and instructions.
The ammit claims to be leak proof, I can't stand having my hands and mod covered in juice, so glad to see geekvape go with this design, I've had zero leaking and I do tend to over squonk (did only use ammit RDA in squonk setup), the airflow holes are on the top part of the RDA, with the air flow going between the chamber and outer wall, it is then lead to 2 holes at the bottom which then reaches the deck from 3 holes, one either side of the coil and one underneath it, there is also a airflow insert under the coil and geekvape supply a 2nd smaller one, they are tiny and a little tricky to work with as so small though.
The airflow on the top cap has a good range from a very tight MTL to a restricted DL, there is 5 hole selections, from 2mm to 0.8mm, and can either use single selection for a hole or multiple holes. Personally I like a semi tight MTL draw and been using single selection on the 1.5mm hole
I used one of clapton coils that comes with the ammit, found building on the ammit simple enough with the 2 post deck. I made sure to position the coil low enough so got hit in the center by the side airflow holes. The coil came out to 0.68ohms, I do normally use clapton coils even for MTL vape, but normally mine are around the 1.5ohm range, but still really liked the supplied coil, and gave a good vape experience.
Being a RDA, wicking is simple enough, I just made sure no cotton was touching the airflow holes on the deck area.
And we are ready to vape
Out of all the newer MTL squonk RDA's I have tried recently, without a doubt the ammit MTL RDA is the best for me, it gives great flavor with smooth airflow, it is easy to build on and I love the airflow design, it is easy to adjust and don't have to worry too much about leaking, I will say I do not like the center airflow insert that can be changed out, it is so small, found tricky to get the other one seated in to the RDA, sure would be easy to lose when changing it out, but once it is changed, really never have to bother with it again.
I like the selection of drip tips, you get a larger metal drip tip, but also a delrin one with a 2nd tip for it, one being 2mm inside, the other 3mm, I liked the 2mm as was also a little longer which I prefer.
I highly recommend the Ammit MTL RDA if into squonking and are a MTL vapor, you won't be disappointed, and I give it a rating of 9.5/10, yes it is that good
Thank you for geekvape supplying the Ammit MTL RDA for this review and if you do want to try it, can purchase from their store HERE