Joyetech Cuboid-OMG I need a degree for this thing!

[Malvada]

Seriously tho, I don't if it's the device or me but, no matter what kind of SS coil I put on my Lemo v2 the Cuboid reads that there is a short in the atomizer or no atomizer at all. I've tried all size wraps through the holes and around the screws and even cleaned the 510 connection and no luck. My other rdta's seem to work ok. Just not that single coil Lemo v2. Suggestions?

 

[ej1024]

Did you do the upgrade yet?


VAPE ON

 

[Malvada]

Did you do the upgrade yet?


VAPE ON

No I haven't. From what I understand the upgrade just gives you 50 extra watts. I don't see how that would change the issue I'm having.

 

[ej1024]

No I haven't. From what I understand the upgrade just gives you 50 extra watts. I don't see how that would change the issue I'm having.

That's not all it is, it fixes issues with SS MODE


VAPE ON

 

[Malvada]

That's not all it is, it fixes issues with SS MODE


VAPE ON

It's jammin' now. I think it just needed to get to room temp, but I shall take your much needed advice. I vaped on my Lemo 2 a little while on my IPV D2 then switched it back to the Cuboid and now it's really chuckin' the clouds! Again thank you! For anyone who needs to know, 10 wraps, spaced, 316L 24g, single coil, inside the holes of the Lemo v2.

 

[Superjeep]

I might be mistaken but if I remember correctly I thought the Lemo 2 could be temperamental with TC builds. You gotta really make sure the connections are tight and clean as with most 2 part decks.

 

[Malvada]

Well, the Lemo and the Billow v2 are giving error messages now. I only have an iPad. Going to Mom's tomorrow to download firmware. However, I need to know if Joyetech Cuboid's firmware is compatible with a Mac OS 10.6.

 

[Superjeep]

Im looking at the joytech site and it indeed lists a mac and pc option

http://www.joyetech.com/mvr-software/?sid=171

 

[Malvada]

Im looking at the joytech site and it indeed lists a mac and pc option

http://www.joyetech.com/mvr-software/?sid=171

Most of the other 200w devices are Mac compatible but only the newer OS. I'll report back and see if Joyetech shows me some love!

 

[Zamazam]

Check the connection from the atty to the 510, the screw off piece with the 510 might not me making good contact with the center airflow positive portion of the mod. Check the clearance between the 2 blocks that you have your coil mounted to. Check the insulator on the negative block on the deck. It's deductive trouble shooting.

 

[Malvada]

Check the connection from the atty to the 510, the screw off piece with the 510 might not me making good contact with the center airflow positive portion of the mod. Check the clearance between the 2 blocks that you have your coil mounted to. Check the insulator on the negative block on the deck. It's deductive trouble shooting.

The Lemo doesn't have any way of adjusting 510. Tried adjusting 510 on the Billow and that didn't work. Not sure what you meant by checking peak insulator. What do you want me to do with it? I mean it's there. Can't tighten it. That part doesn't open.

 

[Zamazam]

Are you using a v1 or v2? Or a Lemo Drop? The mod is reading a very low resistance, causing the "Shorted" message. A bad insulator block on the deck could be to blame, or somehow the 510 insulator is cracked of defective. Look at the air adjustment screw if it is a V1, that insulator on the bottom of the screw might be the culprit.

 

[Malvada]

Are you using a v1 or v2? Or a Lemo Drop? The mod is reading a very low resistance, causing the "Shorted" message. A bad insulator block on the deck could be to blame, or somehow the 510 insulator is cracked of defective. Look at the air adjustment screw if it is a V1, that insulator on the bottom of the screw might be the culprit.

It's a Lemo v2. It works just fine on my other mods. I just have to get this firmware issue taken care of. Then go from there.

 

[Zamazam]

unscrew it 1/2 turn and test, and then another 1/2 turn if it still persists. I think the 510 might be a tad long and squishing the insulator at the bottom of the female 510 adapter on the mod.

 

[Malvada]

unscrew it 1/2 turn and test, and then another 1/2 turn if it still persists. I think the 510 might be a tad long and squishing the insulator at the bottom of the female 510 adapter on the mod.

There was no place to fit a screw driver on the 510 connection on the Lemo v2 that I bought. I think I ended up with a bad Lemo v2 b/c I tried turning it every which way I could and ended up bending the deck. (Laughing) So, I went to Eleaf website and ordered real deal. Thank you so much. You have been a doll!

 

[Zamazam]

Not the 510 connector, the atty itself..LOL

 

[Malvada]

Ok. So, if you can't do the upgrade on the Cuboid you simply must have an authentic, (I ordered mine straight from the eleaf website), Lemo v2 b/c it works great! So does the Chuthulu and Billow. Just like Vulcan said, all connections are clean and are there. BTW-316L SS 6 wraps pinched on the Lemo v2. It came out to read 0.3 ohms.