Anyone out there got a good build for a Mad Hatter RDA/NoisyCricket unregulated series mech mod? Trying to get my ohms to read at a .5 but it seems any builds I try end up catching fire immediately unless they read at 1.1 or higher
How many wraps are in your build? And right now the best build I've got for it is a single coil 12 wrap with 32 gauge Clapton but it reads at a 1.18 ohmsI'm still no vape God, but I have the noisy cricket (it's my go to mod) and I run .5-.8 ohm usually 24 Gauge Kanthal 2.5mm in diameter. The 2.5 gives you more surface area which takes a little longer to heat up so your build won't catch on fire. Also after you build and you do your dry burn getting out the hot spots and such you need to use a different mod something that doesn't send 8.4 unregulated volts to a freshly unfired coil. Hope this helps.
Edit: Also make sure your running dual coil not single
How many wraps are in your build? And right now the best build I've got for it is a single coil 12 wrap with 32 gauge Clapton but it reads at a 1.18 ohms
Im using the Mutation X4 (Much like the Mad Hatter with Side Airflow options also...
I like my vape a bit warmer then most do so I run it around .4, but I would recommend staying between .55-.9 Ohms. You want long coils with a wider diameter for better wicking and less chance of burning your cotton.
My last few Noisy Cricket Builds:
View attachment 41828 View attachment 41829 View attachment 41830 View attachment 41831 View attachment 41832 View attachment 41833
Well to be honest I d0ont suggest it for others but I feel safe enough to do it...If you want to use it and have some sand paper or dremel/grinder then take out the pin and everything on it and grind a half of a thread down so it protrudes more.raymo2u Quick question for you since you have the Noisy Cricket and the Phenotype L. Do you feel as though the pin on the Phenotype protrudes enough to be safe on a hybrid mod? I've been doing double takes on mine when I change the batteries and it's about 1 mm out maybe a little less and I know 1mm is the minimum recommended for safe use of a hybrid top cap. I was just hoping for your Two Cents
Well to be honest I d0ont suggest it for others but I feel safe enough to do it...If you want to use it and have some sand paper or dremel/grinder then take out the pin and everything on it and grind a half of a thread down so it protrudes more.
As long as your battery top if flat and undamaged and you dont crank down on the rda you wont do much to make it dangerous, if you crank it down you risk bending the battery plate and hard shorting/venting your batteries.
Buy clones for replacement parts...I buy clones more often then authentic's just to try things out, if I like it Ill buy the Authentic...and then buy 2 or 3 more clonesI feel pretty safe about it simply because I check it so much and never crank down the RDA. I check to make sure my batteries aren't dented everyday. I think I may grind down a little, but the Phenotype is just so nicely made I don't want to go messing it up... plus it wasn't the easiest Atty to find.
Yea square wire is pretty damn expensive...they make it in 316L and 304 SS.@raymo2u Can you actually buy square wire? or is that just some ultra fat ribbon wire that I've never seen before? I need some of that in my life, so many builds where that would have come in handy, finer gauge ribbon never stays put for me Imma need a link right quick please haha
Yea square wire is pretty damn expensive...they make it in 316L and 304 SS.
304 SS LINK and 316L LINK, I suggest you clean it up very well before use and dryburn it to make sure its clean before use, sometime it can have a weird taste at first and this will remove it.
I used to have one from Altzan Cycles and a Vintage Schwinn Krate...that was almost 10 years ago though...I rocked the Blue Velour seat and 144 spokes and only had the twisted fork/seat post/pedals/ape hangers/ and kickstand, the fork was more angled and the bike almost touched the ground....Ill see if I can find something similar so you get the idea....Thanks! I've been wondering this ever since I started making coils, how much easier it would be for some builds if it was squared off. Or just twisting a single strand to make "Twisted" wire.
When I was taking welding and blacksmithing in school, we made hot and cold twisted rods for various projects, and one of them was Chrome Twisted rods for a custom low-rider bike (more or less like this):
Although incredible gawdy, it was also incredibly fun to build, and has always since intrigued me. Now that I build coils, every time I see a low rider bike I always think "This could make a badass coil, except there's no square vape wire " well I guess I was wrong, gonna have to get my hands on some of this, this could help alot of my ideas come to fruition and make some awesome coils (and TC to boot )
I used to have one from Altzan Cycles and a Vintage Schwinn Krate...that was almost 10 years ago though...I rocked the Blue Velour seat and 144 spokes and only had the twisted fork/seat post/pedals/ape hangers/ and kickstand, the fork was more angled and the bike almost touched the ground....Ill see if I can find something similar so you get the idea....
It was alot like this one but the frame was chrome and the seat was royal blue, the rest was chrome with twisted trim here and there. I did have the full length fenders on it though..The fork was stretched out further in the front and the bike had a lower profile then this:
The bikes that catch my eye now are these 20" Choppers:
I order from here when stocking all the gauges at once, cheaper then buying single spools of each.Where do you order your wire from...I've been looking for the best site to buy from because most of the Brick and Mortars I've been in either only sell 10-30 feet or if they do sell more than that it's ridiculous... Like I would like to get some 100-200 foot spools so I can just build without worrying... I want to try and Alien Wire build because the wicking looks awesome but I know I will need to do it a few times to get it right and I need more wire from the gate.
Anyone out there got a good build for a Mad Hatter RDA/NoisyCricket unregulated series mech mod? Trying to get my ohms to read at a .5 but it seems any builds I try end up catching fire immediately unless they read at 1.1 or higher
I order from here when stocking all the gauges at once, cheaper then buying single spools of each.
LINK for Kanthal (24g-34g/100ft each)
LINK for N80 (26g-36g/100ft each)
Kanthal D LINK, click the store to his other other listings for it..
Some gauges are missing and its not complete buy this is the most cost effective method of buying them and then buying singles for the rest. Look for Kanthal D as its cheaper but retains all the characteristics you would want for vaping.
Heres what Ive posted a while ago in the "Post your builds" thread.What is Kanthal D just a lower grade of Kanthal??? I know Kanthal A1 is supposed to be "best quality" If it retains everything and is clean and tastes the same then thats an awesome tip.