Mephisto RDA by Ivogo 1:1 clone

[Nikkita6]

I just received the Mephisto RDA from Angelcigs.com for review, and the timing couldn't be more perfect because I have seen pics of the Mephisto set up with a SR X, it is sexy as hell, and I just received the X last week.

My initial impression is that this is a very well made RDA, and I appreciate the presentation by Ivogo, It does appear to be an exact 1:1 of the authentic, right down to the spot welded posts on the bottom of the atty. I like that I will be able to run this in single coils, and that the 510 pin is adjustable, so I can use it with my 4nine as well.

I have not built anything yet, but I am definitely looking forward to it, especially after hearing Twisted's thoughts during his clone vs authentic comparison.

 

[chris damron]

I just received the Mephisto RDA from Angelcigs.com for review, and the timing couldn't be more perfect because I have seen pics of the Mephisto set up with a SR X, it is sexy as hell, and I just received the X last week.

My initial impression is that this is a very well made RDA, and I appreciate the presentation by Ivogo, It does appear to be an exact 1:1 of the authentic, right down to the spot welded posts on the bottom of the atty. I like that I will be able to run this in single coils, and that the 510 pin is adjustable, so I can use it with my 4nine as well.

I have not built anything yet, but I am definitely looking forward to it, especially after hearing Twisted's thoughts during his clone vs authentic comparison.

I'm not sure how low you like to build your coils, but this thing is MADE for crazy crazy builds. Either thick wire, twisted wire, or multi coil setups. It also does well in single coil mode, I ran it with a single tiger coil and then a single 22g micro coil and the flavor was on point. My favorite single coil setup was a tiger with 24g and 0.9 ribbon twisted, around 0.3 ohms.

 

[Nikkita6]

I'm not sure how low you like to build your coils, but this thing is MADE for crazy crazy builds. Either thick wire, twisted wire, or multi coil setups. It also does well in single coil mode, I ran it with a single tiger coil and then a single 22g micro coil and the flavor was on point. My favorite single coil setup was a tiger with 24g and 0.9 ribbon twisted, around 0.3 ohms.

I am usually straight forward with a twisted 30gauge micro coil not lower than .7, preferably .9, nothing too fancy .. But I might change it up a bit. Thanks for your feedback, I am excited to give this dripper a go.

 

[Chowder]

I just received the Mephisto RDA from Angelcigs.com for review, and the timing couldn't be more perfect because I have seen pics of the Mephisto set up with a SR X, it is sexy as hell, and I just received the X last week.

My initial impression is that this is a very well made RDA, and I appreciate the presentation by Ivogo, It does appear to be an exact 1:1 of the authentic, right down to the spot welded posts on the bottom of the atty. I like that I will be able to run this in single coils, and that the 510 pin is adjustable, so I can use it with my 4nine as well.

I have not built anything yet, but I am definitely looking forward to it, especially after hearing Twisted's thoughts during his clone vs authentic comparison.

OOOOOOO! That's purdy! Now, where did the wife put that checkbook...........?

 

[Nikkita6]

OOOOOOO! That's purdy! Now, where did the wife put that checkbook...........?

Ahaha .. Its is a very attractive RDA, I am impressed so far by the build quality, not to mention that it looks good on everything that I have paired it.

Now just buy your wife something nice, and she won't mind that new RDA as much.

 

[Chowder]

Ahaha .. Its is a very attractive RDA, I am impressed so far by the build quality, not to mention that it looks good on everything that I have paired it.

Now just buy your wife something nice, and she won't mind that new RDA as much.

Diamonds=New RDA, got it! Thanks for the tip!

 

[M5amhan]

do those screws back out at all when building? doesnt look like they would but thought id ask since i plan on getting one

 

[Nikkita6]

do those screws back out at all when building? doesnt look like they would but thought id ask since i plan on getting one

Yes, of course they do, that is how you catch your wire through the post holes. The post holes are nice and big at 3mm, so you can you use thick wire gauges in dual coils without having issues fitting through the hole.

 

[Nikkita6]

Diamonds=New RDA, got it! Thanks for the tip!

Yup, that's about the jist of it!

 

[kholders]

My Mephisto that I got today is at .1 Ohms. with dual triple parallel coils.