Need the best answer from an expert..

[kennjbroas]

Okay, Ive posted here always but got another problem.. AGAIN..

Got the subtank mini, just over a week ago. First problem was leaking thru the air hole.. Kinda got that solved.. (Kinda)
Really thought this tank was GOOD

Anyways..
Now every time I try to tighten the tank (after refills) it shows no atomizer is found and the atomizer number on my battery does NOT read anything.

The only time I can make it show exact .5 is if i loosen the tank a bit.

Am I really over tightening my tank too much, it can cause it to leak a bit? Not reading my coil properly?

Do you all suggest to replace my o-ring? Whats the best solution?


Sent from my iPod touch using Tapatalk

 

[Mike H.]

Sounds like a 510 issue...not uncommon..any chance you could mention what device it is youre using?

 

[kennjbroas]

Sounds like a 510 issue...not uncommon..any chance you could mention what device it is youre using?

Currently got the Kangertech Subtank Mini on Joyetech Evic VT battery.

This only started happening after changing juices too


Sent from my iPod touch using Tapatalk

 

[Mike H.]

Changing the juice shouldnt have much to do with it anything.

Are you using the occ coils or the rba deck?

 

[kennjbroas]

Changing the juice shouldnt have much to do with it anything.

Are you using the occ coils or the rba deck?

Occ coils.. Just bought it literally 2 days ago lol


Sent from my iPod touch using Tapatalk

 

[Mike H.]

Juice leaking from your air holes can be maybe an indicator of

1.) The coil head is not screwed in all the way. Which can also make you not have contact with the device...the coil makes contact to the pin that makes contact to the device...so if it isnt tight it wont make contact and will also leak juice down into the base and out of your air flow holes....check that first and let me know.

 

[Dan DePippo]

I agree with Mike.. will also add that once juice goes into base be sure to remove coil and dry bottom where it makes contact..juice will disrupt electric current.

 

[kennjbroas]

Juice leaking from your air holes can be maybe an indicator of

1.) The coil head is not screwed in all the way. Which can also make you not have contact with the device...the coil makes contact to the pin that makes contact to the device...so if it isnt tight it wont make contact and will also leak juice down into the base and out of your air flow holes....check that first and let me know.

Ive got that solved already, my problem now is it seems if i try and tighten my tank atomizer doesnt show, the only way it can pop up is if the tank is loosend but i dont want to loosen it too much the juice starts to leak..


Sent from my iPod touch using Tapatalk

 

[rotax]

try a different coil head, but it sounds to me , like they said the coil is loose or wet. good luck.

 

[Mike H.]

Ive got that solved already, my problem now is it seems if i try and tighten my tank atomizer doesnt show, the only way it can pop up is if the tank is loosend but i dont want to loosen it too much the juice starts to leak..


Sent from my iPod touch using Tapatalk

Im not following how juice will leak out if you dont tighten the tank to the 510 tight..installing the tank to the device is not a "seal" to keep juice from leaking out of the tank.
If your coil is installed correctly and you still have a leak then its possible the coil is "flooding" or a bad seal on the coil head itself which means you should replace it and hope for the best.

As far as when you install the tank...if its only making connection in one spot but its not tight when it does then its likely the 510 on the device itself...Im going to guess its a spring loaded 510 in which case the little center pin could be stuck or just defective...get a little screwdriver or something and push on the pin down inside the 510..it should move up and down if its spring load..Press on it a few times and maybe it will spring back into proper place.

Other than that, i have nothing else in mind.

 

[kennjbroas]

Im not following how juice will leak out if you dont tighten the tank to the 510 tight..installing the tank to the device is not a "seal" to keep juice from leaking out of the tank.
If your coil is installed correctly and you still have a leak then its possible the coil is "flooding" or a bad seal on the coil head itself which means you should replace it and hope for the best.

As far as when you install the tank...if its only making connection in one spot but its not tight when it does then its likely the 510 on the device itself...Im going to guess its a spring loaded 510 in which case the little center pin could be stuck or just defective...get a little screwdriver or something and push on the pin down inside the 510..it should move up and down if its spring load..Press on it a few times and maybe it will spring back into proper place.

Other than that, i have nothing else in mind.

Yeah it was the coils gasket, for some reason it seemed like it was getting stuck. As for the leak though im still having that issue. Im trying to grab another tank this week hopefully..

As for a beginner (started a couple weeks ago) what sub ohm tank would you recommend? Im looking for something with alot of flavor and vapor.. Something that wont give up on me after a few days

 

[Jasonfox1988]

I would advise the goblin mini but its a rebuildable only so practice and patients is needed at the start.
Try using a pin to pul the 510 connecter up from ur mod? Not all are spring loaded
Also the 510 connecter on the tank is spring loaded but are prone to get stuck in i have 2 kanger tanks and still use them now and then and never had any if the problems you have been having