Finally got around to testing this out.
Started my build knowing the coil build was odd for this little thing.
Once bending the coil into a knot I figured it looked about right for this configuration.
Decided a good coil for this would be a Comp Wire Triple Caterpillar 0.3X3+0.2mm 28+32GA 3mm ID
First, I want to mention that the threading and O-rings on this thing are TIGHT!
Not just tight, tighter than the super glue that used to hold that dude's hard hat to the beam that he was hanging from back in the early '80s.
Once it was time to put it together....oh shit.
I left the glass connected to the top and just tried to screw it together.
The O-ring bunched up.
I separated the pieces, straightened the O-ring and started again.
Placed a few drops of juice on the O-ring to assist in the process.
This time the O-ring stayed in place.
Just before the glass was fully over the O-ring, the glass broke.
Grabbed the replacement glass from the box and decided to put the glass on separately.
Same thing, just before it passed the O-ring, the glass broke.
Luckily I had purchased the accessory kit that came with 2 additional glass tubes.
Same as the previous time I tried it using the glass by its self.
I was being extremely cautious to ensure I was placing it on as straight as possible.
BAM! Glass number 3 broke.
Now I'm pissed and have 3 broken glass tubes for a brand new tank that I haven't even had the opportunity to test.
To make it worse, this one has a build that I haven't tried before.
(Only single coil I've tried was the Wismec Theorem and it sucked ass IMHO)
However, I tried for a fourth time and it went successfully.
For a coil that was SUPPOSED to be 0.2Ω I was surprised to see it reading .53Ω.
Tested on three other TABs, the Smok Alien, Hcigar VT133, and Ijoy LUX.
Evidently this is a half ohm coil.
Whatever....
Since I am NOT one to read directions before messin with things I was forced to learn the hard way that the top fill cap is NOT threaded.
It is also EXTREMELY tight.
(figured this out after spending 5 minutes TRYING to turn the cap off)
As you can see form the picture, there isn't much to grab onto the try turning.....
(There is a reason for that, don't be a dumb ass like me)
The drip tip is PART OF the top fill cap so just PULL the entire top off to fill.
As you'll notice in the previous picture, the fill holes are plenty big enough.
Not extremely large but easy to fill through.
Once all said and done, the Smok Alien reads it at 0.514Ω
With all that said and done, I was FINALLY able to test this thing.
Started right off @ 100 watts.
Not really because I knew that is where I’d want it, but because that is the setting the previous tank that I had on this Alien was set at.
OH SHIT!!!
I was more than shocked.
Shocked AND impressed.
The flavor from this was absolutely amazing.
Yes, I have many other tanks, RTA, RDTA, and RDA but for a first hit I have never tasted such clean and full flavor.
So naturally I just assumed it was due to the amount of time it sat waiting while I decided to get a piece of cake my wife had just made.
I figured after a few more hits it’d weaken up a bit.
The time on this has only allowed me to get through two and a half fills, but damn it, this thing is still just over packed with flavor.
Since I used my daily juice I knew what to expect.
But this surpassed anything I was anticipating.
Even though I broke 3 glass tubes during this, the flavor MORE than makes up for it.
I already have the stainless and the black version but while I was in a chat with vaporworld finding out how great they are and they’ll be sending me replacement, I ordered another pair of these things.
Yes, I also ordered an additional accessory kit just in case.
I consider the black version more of a gun metal.
Would I replace it if lost?
HELL YEAH.
At this minute vaporworld.biz has them for $9.99 and the accessory kit for $6.99
Thanks for reading.
Started my build knowing the coil build was odd for this little thing.
Once bending the coil into a knot I figured it looked about right for this configuration.
Decided a good coil for this would be a Comp Wire Triple Caterpillar 0.3X3+0.2mm 28+32GA 3mm ID
First, I want to mention that the threading and O-rings on this thing are TIGHT!
Not just tight, tighter than the super glue that used to hold that dude's hard hat to the beam that he was hanging from back in the early '80s.
Once it was time to put it together....oh shit.
I left the glass connected to the top and just tried to screw it together.
The O-ring bunched up.
I separated the pieces, straightened the O-ring and started again.
Placed a few drops of juice on the O-ring to assist in the process.
This time the O-ring stayed in place.
Just before the glass was fully over the O-ring, the glass broke.
Grabbed the replacement glass from the box and decided to put the glass on separately.
Same thing, just before it passed the O-ring, the glass broke.
Luckily I had purchased the accessory kit that came with 2 additional glass tubes.
Same as the previous time I tried it using the glass by its self.
I was being extremely cautious to ensure I was placing it on as straight as possible.
BAM! Glass number 3 broke.
Now I'm pissed and have 3 broken glass tubes for a brand new tank that I haven't even had the opportunity to test.
To make it worse, this one has a build that I haven't tried before.
(Only single coil I've tried was the Wismec Theorem and it sucked ass IMHO)
However, I tried for a fourth time and it went successfully.
For a coil that was SUPPOSED to be 0.2Ω I was surprised to see it reading .53Ω.
Tested on three other TABs, the Smok Alien, Hcigar VT133, and Ijoy LUX.
Evidently this is a half ohm coil.
Whatever....
Since I am NOT one to read directions before messin with things I was forced to learn the hard way that the top fill cap is NOT threaded.
It is also EXTREMELY tight.
(figured this out after spending 5 minutes TRYING to turn the cap off)
As you can see form the picture, there isn't much to grab onto the try turning.....
(There is a reason for that, don't be a dumb ass like me)
The drip tip is PART OF the top fill cap so just PULL the entire top off to fill.
As you'll notice in the previous picture, the fill holes are plenty big enough.
Not extremely large but easy to fill through.
Once all said and done, the Smok Alien reads it at 0.514Ω
With all that said and done, I was FINALLY able to test this thing.
Started right off @ 100 watts.
Not really because I knew that is where I’d want it, but because that is the setting the previous tank that I had on this Alien was set at.
OH SHIT!!!
I was more than shocked.
Shocked AND impressed.
The flavor from this was absolutely amazing.
Yes, I have many other tanks, RTA, RDTA, and RDA but for a first hit I have never tasted such clean and full flavor.
So naturally I just assumed it was due to the amount of time it sat waiting while I decided to get a piece of cake my wife had just made.
I figured after a few more hits it’d weaken up a bit.
The time on this has only allowed me to get through two and a half fills, but damn it, this thing is still just over packed with flavor.
Since I used my daily juice I knew what to expect.
But this surpassed anything I was anticipating.
Even though I broke 3 glass tubes during this, the flavor MORE than makes up for it.
I already have the stainless and the black version but while I was in a chat with vaporworld finding out how great they are and they’ll be sending me replacement, I ordered another pair of these things.
Yes, I also ordered an additional accessory kit just in case.
I consider the black version more of a gun metal.
Would I replace it if lost?
HELL YEAH.
At this minute vaporworld.biz has them for $9.99 and the accessory kit for $6.99
Thanks for reading.
