Hi there. I wanted to seek some opinions and reviews on what ATTY either RTA/RDA/RDTA is better or best in providing denser and better in flavor.
NOTE:
Not into OCCs
NOTE:
Not into OCCs
Become a Patron!
Recommendations
- Thread starter snooooogle
- Start date
For flavor I like what Augvape has to offer. The Boreas, Alleria, and Merlin all produce great flavor but the Boreas is my favorite.
Sent from my SAMSUNG-SM-N915A using Tapatalk
Sent from my SAMSUNG-SM-N915A using Tapatalk
My top three right now are:
Engine rta by OBS
Modfather RTA
Mage Rta by coil art
All three of these have incredible flavor and density, depending on build.
Sent from my SM-G935V using Tapatalk
Can you provide any suggestions on what type of builds can be good?
Btw, just to add up I currently have a Limitless Plus RDTA
using dual coils with fused clapton at 3mm guide 5 loops I think it's both .26 kanthal wires.
Some friend also suggested to try out .6 kanthal with 8 to 9 loops
Well, I'm a bit biased in that regard because I'm a big fan of stainless steel. But, my favorite builds for these tanks are (All 316L):
Engine: 28x2/40 fused 3mm 7 wraps
Mage: 32x3/40 twisted fused 3mm 8 wraps
Modfather: .4x.1 x 8 / 40g staple 3mm 5 wraps
Sent from my SM-G935V using Tapatalk
Hi! Sorry for this dumb question.
I'm actually quite confused, I quite understood that you were referring to 28x2 like .26 and 2 pcs of it not sure with 40. Could you please educate me
Thank you!
It's just a shorthand way of explaining a particular build. So for 28x2/40 what I'm saying is a fused clapton composed of two parallel 28 gauge core wires, then claptoned together with a 40 gauge overwrap.Hi! Sorry for this dumb question.
I'm actually quite confused, I quite understood that you were referring to 28x2 like .26 and 2 pcs of it not sure with 40. Could you please educate me
For the 32x3/40 I'm saying 3 strands of 32 gauge wire twisted tightly together then claptoned over with 40gauge
For the staple, I'm saying .4mmx.1mm ribbon stacked vertically together then claptoned together with 40 gauge wire.
I really prefer the very tiny gauge outer wraps on clapton (40 gauge is very small, almost like a strand of hair)
Here is a picture of the staple I was talking about:
That is extremely zoomed in, for scale the background is fabric.
I hope I answered your question, if that isn't what you meant just let me know.
Sent from my SM-G935V using Tapatalk
It's just a shorthand way of explaining a particular build. So for 28x2/40 what I'm saying is a fused clapton composed of two parallel 28 gauge core wires, then claptoned together with a 40 gauge overwrap.
For the 32x3/40 I'm saying 3 strands of 32 gauge wire twisted tightly together then claptoned over with 40gauge
For the staple, I'm saying .4mmx.1mm ribbon stacked vertically together then claptoned together with 40 gauge wire.
I really prefer the very tiny gauge outer wraps on clapton (40 gauge is very small, almost like a strand of hair)
Here is a picture of the staple I was talking about:
That is extremely zoomed in, for scale the background is fabric.
I hope I answered your question, if that isn't what you meant just let me know.
Sent from my SM-G935V using Tapatalk
Thank you sir for the very detailed response. However. I think i can do that diy process if i have the tools hehe. I usually use like pre-built spaced fused claptons or just kanthal wires
Well, obviously I'm in favor of pre-built wire as well, otherwise I'd be out of a job
Sent from my SM-G935V using Tapatalk
Well, obviously I'm in favor of pre-built wire as well, otherwise I'd be out of a job
Sent from my SM-G935V using Tapatalk
Haha. Well..i'll be checkong you recommendation for the RTAs and hopefully it should be available here in the PH