Become a Patron!
Sense Blazer Pro
- Thread starter Paratech
- Start date
Entire tank height: 68.6mm
64.2mm without 510
52mm without 510 or drip tip
Glass:
28.1mm tall X 27.8 OD (installed)
23.5mm X 27.7mm OD (to use other coils like original Blazer 200, TFV8, and OBS V)
Sense Blazer 200, Smok TFV8, and OBS V coils fit and work great in this if you switch to the shorter glass (6ml) so the coil can reach the chimney.
Top Cap:
27.8mm OD X 21.5mm tall including chimney
Drip tip through chimney:
12.7mm ID tapering to 8.5mm ID
Juice fill holes:
9.9mm X 4mm
It has the same locking mechanism that the previous version had. (Sense Blazer 200)
A small hook that slides into a channel by only a slight (1/12th) turn.
Yes, there IS a slight wobble to the hinge.
This is to allow that 1/12th turn to happen.
Just like many battery doors on mods, if you remove the wobble, it can't turn or slide.
You will not hear me complain about something that works as designed.
Last edited:
Drip Tip:
17mm tall
17.5mm OD tapering to 15.5mm OD
13mm ID tapering to 9mm ID
It is a 12.5mm OD drip tip
Base:
27.9mm OD X 15.1mm tall (excluding 510)
14.5mm deep
inside threads (where coil threads in):
16.55mm ID
Floating copper 510 pin
There are four airflow holes that measure 7.9mm X 3mm with hard stops from full open to full closed.
Last edited:
So it is already evident that is looks great on the Ijoy Captain PD270 (although it would look even better on the rainbow version) so lets see how it looks on other mods:
Ijoy LUX 215
Wismec EXOSkeleton ES300
(look, it isn't on fire......yet)
Smok GX350
Ijoy Maxo
Laisimo SnowWolf 200 Plus
DigiFlavor DF 200
Smok X Cube Ultra
Smok Alien 220
Smok G-Priv
HohmTech HohmWrecker G2
Ijoy LUX 215
Wismec EXOSkeleton ES300
(look, it isn't on fire......yet)
Smok GX350
Ijoy Maxo
Laisimo SnowWolf 200 Plus
DigiFlavor DF 200
Smok X Cube Ultra
Smok Alien 220
Smok G-Priv
HohmTech HohmWrecker G2
Last edited:
My vaping experience with the 2 supplied coils:
I was able to fit 7.5ml juice in after priming the coil.
0.3Ω coil rated 60 - 150 watts:
10 hits on each setting (chain vape style)
Airflow wide open.
Waited 5 minutes between each setting just in case the coil was the type to get hot and stop producing flavor.
60 - even though it seemed I wasn't even hitting the fire button, it actually produced some vapor but NO flavor.
70 - a little more vapor production and the flavor is just starting to show up.
80 - plenty of vapor, a slight bit more flavor.
90 - Room filling clouds, flavor really coming to life. Tank not yet warm.
100 - Even more clouds, flavor is almost perfect. Very full bodied and thick. Tank not yet warm.
110 - Clouds still building, flavor enough it made me take an additional 10 hit. mmm good stuff here. Tank almost warm.
120 - I really didn't expect more clouds but sure enough, there is more. Flavor increased by just a little. Tank not warm.
130 - Those damn clouds still increasing as well as a bit more flavor. Still a cool vape after 10 chain vapes. Wicking is keeping up just fine. Time to refill due to a few extra hits since it is tasting so good.
140 - Don't really notice any difference from 130 watts.
150 - A slight bit more cloud and more importantly a little more flavor.
160 - Wow, THIS is a perfect place to stop adjusting. I like it right here.
Flavor is perfect, temperature is just starting to reach a "warm" spot.
After chain vaping 35 hits, the tank is also just reaching warm.
Wicking is having no trouble keeping up.
I'm sure the coil is capable of keeping up with wicking and continue to climb above the 160 mark but I didn't test that.
For me, sticking in this upper range is where my preference is for flavor production.
By no means would I consider this a loud vape but is also isn't a silent one.
I would compare it to the SteamCrave Aromamizer Plus as far as noise volume.
The Sense Blazer Pro is just a little higher pitch in comparison.
This just has a tiny bit more airflow though.
No leaks, no condensation.
The 0.3Ω Blazer Pro coils are uniquely designed combining dual vertical parallel coils, dual horizontal parallel coils, organic cotton wicking, and a ceramic inner housing.
The outer coil housing is made of stainless steel and has six large wicking ports for continuous saturation.
Air is brought in from the four 8mm by 3mm adjustable air slots located at the base of the tank and runs through the center of the vertical coils and through auxiliary air channels in the ceramic to the horizontal coils.
I used this 0.3Ω coil for 31 tank fills and it was still going strong with no signs of end of life.
Considering I use super sweet juice with high flavor percentage this is definitely extremely long coil life for me.
Decided I'd switch over to the 0.2Ω coil so I could at least get everything logged.
I did NOT close the air flow during tank refills and id did NOT have any negative results.
After priming, I fit 5.5ml juice in with this coil due to having to switch to the shorter glass.
0.2Ω coil rated for 60 - 200 watts
This coil seemed to be just a little louder than the 0.3Ω
60 - Are there batteries in this thing, is it powered on? I see just a tiny bit of vapor but taste nothing.
70 - It seems powered on because I can clearly see more volume of vapor production but only a slight tough of flavor thinking about coming around.
80 - A little more flavor and cloud but still excessively weak for my tastes.
90 - Barely a noticeable increase from 80 watts.
100 - A little more vapor production and the flavor is just starting to ramp up.
110 - Flavor is really starting to come out now. Tank just starting to get warm.
120 - Really starting to like where this is going. Flavor increasing pretty well. Naturally vapor production is as well.
130 - I didn't really detect a change from 120
140 - Pretty good improvement. Really liking the flavor production. Vapor production equally increased.
150 - A little more flavor, a little more vapor.
160 - Noticeable increase in flavor and some added vapor to go along with it. Only a "warm" vape not hot however the glass is indeed heated.
170 - Not much change in flavor but more clouds are apparent.
180 - The flavor now matches the huge clouds that are filling the room. Not bad at all.
190 - For me, this just tastes right. Exactly how I want to vape. A nice warm full bodied vape with loads of flavor.
200 - THAT hit the spot, don't change a thing. Forget what I said about 190, THIS is where it needs to be.
For my vaping style, my DIY juice, and what I like, 200 watts seems to fit perfectly.
I use VG based NIC at 2.2%, 30% flavorings, and fill the rest with VG.
Normally with that mix and with it being super sweet it just kills coils in a few days.
These two coils don't seem to follow what all the rest have done.
Only other factory coil I get good life from is the Smok Micro TFV4 and that lasts 2 weeks.
These coils surpass that by a little and have no trouble keeping up while chain vaping.
So for me, THESE are the coils I'll use when I'm not using an RTA/RDTA.
I am right at 3000 hits into this tank (both coils combined) and really enjoy it.
I like the 0.3Ω coil a bit more simply because it produces just a little more flavor.
Maybe it is just a better match for my particular DIY juice, maybe it's just a better balanced coil.
Just like with the Blazer 200, I really like this design of top fill.
I was able to fit 7.5ml juice in after priming the coil.
0.3Ω coil rated 60 - 150 watts:
10 hits on each setting (chain vape style)
Airflow wide open.
Waited 5 minutes between each setting just in case the coil was the type to get hot and stop producing flavor.
60 - even though it seemed I wasn't even hitting the fire button, it actually produced some vapor but NO flavor.
70 - a little more vapor production and the flavor is just starting to show up.
80 - plenty of vapor, a slight bit more flavor.
90 - Room filling clouds, flavor really coming to life. Tank not yet warm.
100 - Even more clouds, flavor is almost perfect. Very full bodied and thick. Tank not yet warm.
110 - Clouds still building, flavor enough it made me take an additional 10 hit. mmm good stuff here. Tank almost warm.
120 - I really didn't expect more clouds but sure enough, there is more. Flavor increased by just a little. Tank not warm.
130 - Those damn clouds still increasing as well as a bit more flavor. Still a cool vape after 10 chain vapes. Wicking is keeping up just fine. Time to refill due to a few extra hits since it is tasting so good.
140 - Don't really notice any difference from 130 watts.
150 - A slight bit more cloud and more importantly a little more flavor.
160 - Wow, THIS is a perfect place to stop adjusting. I like it right here.
Flavor is perfect, temperature is just starting to reach a "warm" spot.
After chain vaping 35 hits, the tank is also just reaching warm.
Wicking is having no trouble keeping up.
I'm sure the coil is capable of keeping up with wicking and continue to climb above the 160 mark but I didn't test that.
For me, sticking in this upper range is where my preference is for flavor production.
By no means would I consider this a loud vape but is also isn't a silent one.
I would compare it to the SteamCrave Aromamizer Plus as far as noise volume.
The Sense Blazer Pro is just a little higher pitch in comparison.
This just has a tiny bit more airflow though.
No leaks, no condensation.
The 0.3Ω Blazer Pro coils are uniquely designed combining dual vertical parallel coils, dual horizontal parallel coils, organic cotton wicking, and a ceramic inner housing.
The outer coil housing is made of stainless steel and has six large wicking ports for continuous saturation.
Air is brought in from the four 8mm by 3mm adjustable air slots located at the base of the tank and runs through the center of the vertical coils and through auxiliary air channels in the ceramic to the horizontal coils.
I used this 0.3Ω coil for 31 tank fills and it was still going strong with no signs of end of life.
Considering I use super sweet juice with high flavor percentage this is definitely extremely long coil life for me.
Decided I'd switch over to the 0.2Ω coil so I could at least get everything logged.
I did NOT close the air flow during tank refills and id did NOT have any negative results.
After priming, I fit 5.5ml juice in with this coil due to having to switch to the shorter glass.
0.2Ω coil rated for 60 - 200 watts
This coil seemed to be just a little louder than the 0.3Ω
60 - Are there batteries in this thing, is it powered on? I see just a tiny bit of vapor but taste nothing.
70 - It seems powered on because I can clearly see more volume of vapor production but only a slight tough of flavor thinking about coming around.
80 - A little more flavor and cloud but still excessively weak for my tastes.
90 - Barely a noticeable increase from 80 watts.
100 - A little more vapor production and the flavor is just starting to ramp up.
110 - Flavor is really starting to come out now. Tank just starting to get warm.
120 - Really starting to like where this is going. Flavor increasing pretty well. Naturally vapor production is as well.
130 - I didn't really detect a change from 120
140 - Pretty good improvement. Really liking the flavor production. Vapor production equally increased.
150 - A little more flavor, a little more vapor.
160 - Noticeable increase in flavor and some added vapor to go along with it. Only a "warm" vape not hot however the glass is indeed heated.
170 - Not much change in flavor but more clouds are apparent.
180 - The flavor now matches the huge clouds that are filling the room. Not bad at all.
190 - For me, this just tastes right. Exactly how I want to vape. A nice warm full bodied vape with loads of flavor.
200 - THAT hit the spot, don't change a thing. Forget what I said about 190, THIS is where it needs to be.
For my vaping style, my DIY juice, and what I like, 200 watts seems to fit perfectly.
I use VG based NIC at 2.2%, 30% flavorings, and fill the rest with VG.
Normally with that mix and with it being super sweet it just kills coils in a few days.
These two coils don't seem to follow what all the rest have done.
Only other factory coil I get good life from is the Smok Micro TFV4 and that lasts 2 weeks.
These coils surpass that by a little and have no trouble keeping up while chain vaping.
So for me, THESE are the coils I'll use when I'm not using an RTA/RDTA.
I am right at 3000 hits into this tank (both coils combined) and really enjoy it.
I like the 0.3Ω coil a bit more simply because it produces just a little more flavor.
Maybe it is just a better match for my particular DIY juice, maybe it's just a better balanced coil.
Just like with the Blazer 200, I really like this design of top fill.
Last edited:
Box and bottom of tank say designed and manufactured by CIGREAT Technology
Their website has the Blazer 200 but not the Blazer Pro
From http://www.szsensetech.com/Products/senseblaze.html ;
Sense blazer pro super sub ohm tank
Top Filling
Size: 68.3(L)*27.8(D)mm
6ML+1ML Juice Capacity
Stainless Steel Construction
Adjustable Bottom Airflow
Coils are Interchangeable to Blazer 200 When Switch to the Short Glass Tube
Hotline:0086-755-61118088
Email:[email protected]
Specifications:
• Top Filling
• Size: 68.3(L)*27.8(D)mm
• 6ML+1ML Juice Capacity
• Stainless Steel Construction
• Adjustable Bottom Airflow
• Coils are Interchangeable to
Blazer 200 When Switch to the Short Glass Tube
****************************************************************************************************************
Sense Blazer Pro Sub-Ohm Tank Features:
•0.2Ω Sextuple Coil - rated for 60 to 200W
•0.3Ω Blazer Pro Coil - Dual Vertical & Horizontal Design
•28mm Diameter
•510 Drip Tip Adapter
•6mL Optional Glass For Blazer 200, TFV8 Coils & OBS V coils
•7mL Maximum Juice Capacity for Blazer Pro coils
•Black Delrin Ultra-Wide Drip Tip
•Compatible with Sense Blazer 200, Smok TFV8, and OBS V coils
•Copper-Plated 510 Connection
•High-Grade Glass Reinforcement
•Innovative Flip Top-Fill Design with Hinge Lock
•Quad Adjustable Airflow Control at Base
•Superior Stainless Steel Construction
Package Includes:
•1 Sense Blazer Pro Sub-Ohm Tank
•1 0.3Ω Blazer Pro Ceramic Coil
•1 0.2Ω Blazer 200 Coil
•510 Drip Tip Adapter
•1 Short 6ml Glass Segment
•Spare O-rings Pack
Their website has the Blazer 200 but not the Blazer Pro
From http://www.szsensetech.com/Products/senseblaze.html ;
Sense blazer pro super sub ohm tank
Top Filling
Size: 68.3(L)*27.8(D)mm
6ML+1ML Juice Capacity
Stainless Steel Construction
Adjustable Bottom Airflow
Coils are Interchangeable to Blazer 200 When Switch to the Short Glass Tube
Hotline:0086-755-61118088
Email:[email protected]
Specifications:
• Top Filling
• Size: 68.3(L)*27.8(D)mm
• 6ML+1ML Juice Capacity
• Stainless Steel Construction
• Adjustable Bottom Airflow
• Coils are Interchangeable to
Blazer 200 When Switch to the Short Glass Tube
****************************************************************************************************************
Sense Blazer Pro Sub-Ohm Tank Features:
•0.2Ω Sextuple Coil - rated for 60 to 200W
•0.3Ω Blazer Pro Coil - Dual Vertical & Horizontal Design
•28mm Diameter
•510 Drip Tip Adapter
•6mL Optional Glass For Blazer 200, TFV8 Coils & OBS V coils
•7mL Maximum Juice Capacity for Blazer Pro coils
•Black Delrin Ultra-Wide Drip Tip
•Compatible with Sense Blazer 200, Smok TFV8, and OBS V coils
•Copper-Plated 510 Connection
•High-Grade Glass Reinforcement
•Innovative Flip Top-Fill Design with Hinge Lock
•Quad Adjustable Airflow Control at Base
•Superior Stainless Steel Construction
Package Includes:
•1 Sense Blazer Pro Sub-Ohm Tank
•1 0.3Ω Blazer Pro Ceramic Coil
•1 0.2Ω Blazer 200 Coil
•510 Drip Tip Adapter
•1 Short 6ml Glass Segment
•Spare O-rings Pack
Last edited:
Thanks KingPin!
Question, I really really want this tank. Currently have a Wismec Reuleaux RX200S. Not sure if the pin placement is the same on my RX200s as it is on your RX2/3. Do you think I would have extensive overhang with this tank?
Just about 1mm overhang on the front of the RX200S
Sent from my SM-N910P using Tapatalk
Just about 1mm overhang on the front of the RX200S
Sent from my SM-N910P using Tapatalk
awesome, thank you for that, thats not bad at all. Do you think this would consume more juice than a TFV8?
@Paratech would be able to answer that better than me, I just got mine last week.
Sent from my SM-N910P using Tapatalk
Thanks gakudzuOutstanding review!
Your thoroughness is appreciated
Thanks mjag
As mjag showed (and saved me from having to upload another picture) there IS just a little overhang and the 200S and 2/3 have the SAME pin placement.
They both drink juice like there is no tomorrow.
Since I go through about 45ml/day I don't notice it too much though.
With that said: the TFV8s most generally are a bit more thirsty.
Both great tanks.
As I said somewhere up there, if you switch to the shorter (6ml) glass, you can use the Blazer 200, TFV8 Coils & OBS V coils so it provide you the opportunity to decide what coils you like better.
Myself, I like the 0.3Ω Ceramic coil best.
But that is pretty subjective.
Last edited:
Thanks WhiskeyMonster tank, Para....Really liked the review and especially liked the over hang pic, just above^^^ You put a lot of work into this review, excellent job
I think every monster tank should have a jamming guitar to sit on.
lol
I've been looking for an answer on whether high vg liquid is ok with this tank or not and found your review. Wow, great job, made my life much easier.
just got my rainbow today
Sent from my iPad using Tapatalk
just got my rainbow today
Sent from my iPad using Tapatalk
Thanks centella4u, glad you found it helpful.I've been looking for an answer on whether high vg liquid is ok with this tank or not and found your review. Wow, great job, made my life much easier.
just got my rainbow today
I've been pretty happy with it and don't see that changing.
I definitely need to order some more 0.3Ω coils though.
Your post provoked me to test it with nothing but 100% VG.
It had no troubles at all.
Chain vaped 3ml straight through.
Tank got a bit warm (hot) but wicking was NOT an issue.
Thanks buddy, here it sits on some mods (I think) you haven't posted
This is Ace Vaper aka centella4u & aceman3330
Sent from my iPad using Tapatalk
This is Ace Vaper aka centella4u & aceman3330
Sent from my iPad using Tapatalk
Nice pics and they are of 4 mods I do not have.Thanks buddy, here it sits on some mods (I think) you haven't posted
This is Ace Vaper aka centella4u & aceman3330
SirRichardRear
AKA Anthony Vapes on Youtube
VU Donator
Diamond Contributor
Member For 3 Years
Reviewer
Nice review para, that rainbow is sexy
Thanks SirRichardRear
I think almost everything looks good on that mod.
lol you might be right. I also have the black leather with the gold pharaoh rta looks nice too.
Hey guys, received my tank in the mail today. Got it all primed up and ready to go, wasnt getting good flavor from it. Tried different wattages, still nothing. There were times where i would get some good flavor, but 90% of the time, its nothing special. Had 2 separate leaking issues too. Not sure if it's the juice I'm using or what. Using some juice from Fuzion (I've heard its a 65/35 VG/PG blend) checked all seals and everything looks good, as well as the factory coil. Any suggestions on what could be causing the lack of flavor/leaking issues?
I had a leak issue at first. I wasn't looking the top all the way. Make sure you twist it all the way. Once I figured that out no more leaks. I now own two and love them. As far as flavor goes idk I thought it was absolutely incredible from the start. Hope this kinda helps.
Double check the O-ring around the coil.
Since none of mine have leaked I haven't had to try to stop one form leaking.
Sometimes I'm lucky like that, sometimes not.
Based on closely inspecting the tank many times during the review and usage I can say that there is a high probability that IIIDEADLYIII is correct.
If it isn't fully closed or locked into position it could allow the juice to pass through, especially thinner juice.
Sorry I don't have a definitive answer due to not experiencing the same issue.
Don't see how that'd have anything to do with flavor though.
All the coils I have used in it have produced good to great flavor.
Maybe the entire problem is simply you were unlucky enough to get some shit coils.
It's possible.