Triton RTA System

[Manimal3497]

Got me a triton which i love. When I purchased the tank from efun.top I also purchased the RTA system. I went to use it for the first time the other night and screw does not go in the hole far enough to hold the kanthal in place. I even tried with 24g and still wouldnt hold it. The screw is flush with the outside but can barely see it when you look through the hole the kanthal runs through when it is tightened down. I emailed Aspire about it and was told that Efun.top is on their copy cat list and that if I buy something from them then they can throw in some free screws. What I am wondering is has anyone else had this issue? If so were you able to fix it somehow or get new screws that worked? I have went through my hole parts bottle and cannot find any small enough diameter wise to even work. I have an email in with efun.top to see if they can help but in case they wont I want to see if I can figure out other option with it. I ordered a couple of the atlantis/anyvape heads from ohmbusters until I can figure it out but I really want to use the triton one for the vertical build ability.

 

[BoomStick]

Get some grub screws. No head on them to limit how far you can screw them in.

 

[Nailz]

You should of got spare screws with the RTA, have you tried them too?

 

[Manimal3497]

thats what i though was in these but it still only lets me go so far. Wonder if maybe its going it an a angle then. Imma have to check it out more see if I can tell if that is the case. I have a bunch of grub screws from my orchids and kayfuns but none of them are small enough.

 

[Manimal3497]

You should of got spare screws with the RTA, have you tried them too?

yes I tried that to and same issue

 

[Nailz]

yes I tried that to and same issue

Then it must be the holes, maybe something stuck on the threading, maybe give it a soak in a hot bath, I've had no problems with mine except it just isn't that good, much prefer the Segatank Atlantis V2 RBA head on the triton myself.

 

[Manimal3497]

I will have to see if that works. I bought 2 of the Segatank V2 RBA heads (1 for the triton and 1 for my starre) but was hoping to use the triton for vertical coils if I can get it to work.

 

[BoomStick]

Can you just put an extra piece of wire in the hole along with the coil leads, tighten down on both pieces and then 'wiggle till it breaks off' the extra wire? Could be a quick fix for now.

 

[Manimal3497]

I can almost stick a paper clip through the hole with the kanthal in there while its tightened down.

 

[BoomStick]

Wow. That sucks.

 

[Pauly Walnuts]

The screw bottoms are probably flat the the hole for the kanthal is most definately round.
kinda like this >> [[[[[[[[[[])<<<<<<< See the gap
If this is the case, Take a small drill bit, slightly smaller than the screw hole and counter sink the other side, where the screw makes contact. You could also try rounding the bottoms of the screw, if thats whats keeping it from going all the way through.
I saw one of these kits today and saw the gap you are talking about. Though I didnt pay attention to why it was like that.

 

[Rdnekrick]

Same issue..I emailed them and got the same response. Buy something and they'll send screws.. That's not gonna FIX it.. I looked for a tap that size to finish the threads and the only one I could find was 90 bucks! Funk that! I'm just gonna return the damn thing.

 

[Manimal3497]

I will have to see if I have a drill bit small enough. Looking through the hole its barely coming through the hole at all if that makes any sense. I emailed Efun.top and was told to take a picture of it. I let them know not sure how I am suppose to get a picture of a small hole inside but I will try when I get home. I dont know what it is with china and take a picture of the hard to see normally let alone with a camera things.

 

[Manimal3497]

Looks like efun.top does not like to do anything to fix the problem. They told me to send them pics or video of the issue so I sent them an email telling them I have no clue how I am suppose to get a picture of that itty bitty hole. A coworker helped me make a video of me sticking a paper clip through it while it is tightened down so I put it on google drive and sent them a link. Needless to say that was a week ago and no response so guess I am SOL on that rebuildable.

I have gotten my anyvape rebuildable's from OHM Busters. I am having an issue though hoping someone can tell me what I am doing wrong. I thread in my wick (have tried cotton and elfwick) pull up my bunny ears slide the cap over clip just a little bit above then tuck it back in. The first time I just tucked it down and made sure it was covering the holes. No dry hits vaped great as long as I was using it on a regular basis. I left it overnight and it leaked all over. Next I tried tucking it down and pulling it through the holes and trimming off any extra. I get a dry hit here and there and it still leaked some overnight. Not near as bad but still a puddle at the base of my tank. How are you guys wicking these? Are you having leaking with them?

 

[Manimal3497]

Realized there are juice channels at the bottom so I cut the wick tucked it down on the lil bit of deck then screwed the other piece back on and then readjusted to cover the holes. Hopefully that will work. No dry hits yet. Have to see if it leaks while I sleep tonight. Thought it was kinda cool for the first time my juice holes on the side actually match up with the holes on the chimney of the triton lol

 

[Manimal3497]

Well that didnt work still leaks :/