whats that screw supposed to do?I twist mine a bit so the wick stays up against the glass/rear of the Boro.
Sent from the Death Star
whats that screw supposed to do?I twist mine a bit so the wick stays up against the glass/rear of the Boro.
Sent from the Death Star
The wicking ports are greatly improved over the Exocet AND it has those juiceflow screws that you can raise or lower to fit whatever wicking you use. I managed to get the Exocet where I wanted it with a 3mm coil, but it is not forgiving. You have to get it just right and then twist the top cap a bit to squeeze the cotton. That is a thing of the past with the Xeta.I tried the exocet clone a long time ago and all i got were dry hits or flooding. So I was afraid of the same thing with the xeta. I do like the build deck though.
I replied before you asked this question, but that's the answer lolwhats that screw supposed to do?
If for some reason I need to open it up before it's empty I just use the juice bottle to suck the remaining juice out. Hold the bottle upright, squeeze some air out, tilt the juice in the boro to a corner and stick the nozzle in there and let go. Same with the Exocet.I still dont understand how you can empty a tank with the wicks being so high.
Yeah, with the YFTK clone, the chimney and bottom seal thing were pretty tight .Have to make sure everything's lubed up with some juice and even then took a little effort, but worked out fine.My only beef with the Xeta is that your boro o-rings have to be pristine otherwise they bunch up on you. I can deal with that though... Looking into getting some softer red ones from Amazon.
So, how long before SXK will drop this one on the market? I'm sure it will be cheaper and the only question is whether or not it plays nice with the authentic Xeta.
Music to my ears. Exactly how I vape, and 2 Xeta's on the way. Can't wait!2.5mm coil and you should have plenty of wick to fill the space. I use a 2mm and raise the screws on the sides. Works perfectly for me. No gurgling, no dry hits... but I vape MTL and 60/40 vg/pg, too so take that into account.
Sent from the Death Star
Oh yeah you won't be disappointed! The airflow button with the two small holes is my absolute favorite!Music to my ears. Exactly how I vape, and 2 Xeta's on the way. Can't wait!
Sent from my SM-G920R4 using Tapatalk
Good question, figured they would get around to it by now to get an extra 5 bucks for the set.So, how long before SXK will drop this one on the market? I'm sure it will be cheaper and the only question is whether or not it plays nice with the authentic Xeta.
Me and Bear are stuck with the Goldilocks syndrome, hahaThe airflow button with the two small holes is my absolute favorite!
Sent from the Death Star
As far as I know it's the same as the authentic. Todd goes over them herewhat are the hole sizes that it comes with? 3fvape doesnt list anything
Looks like I'll go with the 1.4mm.
A couple configurations do, most don't exactly.Looks like I'll go with the 1.4mm.
Why wouldn't the chimney inserts match the airflow inserts?
Sent from my SM-G950U using Tapatalk
Why wouldn't the chimney inserts match the airflow inserts?
Sent from my SM-G950U using Tapatalk
Looks like I need to read your post 2 or 3 time too as I'm dumb, mostly.Looks like I'll go with the 1.4mm.
Why wouldn't the chimney inserts match the airflow inserts?
Sent from my SM-G950U using Tapatalk
There ya go...Volumetrics
Can achieve greater concentrations with smaller inlets to outlets with less suction.
Same goes in reverse, can have greater head pressure with a larger inlet to a smaller outlet
Sent from my iPhone using Tapatalk
@~Don~ lolWait how does 2x1mm holes =1.4mm?
Sent from my SM-G950U using Tapatalk
Wait how does 2x1mm holes =1.4mm?
Sent from my SM-G950U using Tapatalk
Guys, we need to prowl the other threads and pull some more people into this rabbit hole.
So we have more people to buy our stuff lol.
Sent from my SM-G950U using Tapatalk
Yeah it definitely feels a lot tighter than 1.4mm total. Feels more like 1.0 to me... tighter than a 1.2 on my Dvarw.I just used the 2x1mm insert under the coil and no chimney reducer and it's pretty tight. I'm going to try it with the 3mm chimney reducer next. I know that won't make it any tighter, but it might further increase the vapor concentration and therefore the flavor which is already really good.
I take it you're also using the 2x1?Yeah it definitely feels a lot tighter than 1.4mm total. Feels more like 1.0 to me... tighter than a 1.2 on my Dvarw.
If that's the one with the smallest two airholes, yep.I take it you're also using the 2x1?
Posted this awhile back. Got these of Amazon but they show unavailable now.Agreed on all counts, but I have a couple authentics. Best BB RBA I've used and I've tried the Exo, Insider, and VapeShell. My only beef with the Xeta is that your boro o-rings have to be pristine otherwise they bunch up on you. I can deal with that though... Looking into getting some softer red ones from Amazon.
Sent from the Death Star
I'm really curious to hear how you like the Xeta, and me as well. Like you, I love the vapeshell. My only complaint was the af plastic thingy, hated it. But I just put an o ring on there that reduces it by about 1/2, and I find it really hard to think I will like the Xeta better, but man if I do.......Looks like I'll go with the 1.4mm.
Why wouldn't the chimney inserts match the airflow inserts?
Sent from my SM-G950U using Tapatalk
ditto. The only thing i like more on the xeta (without having used it yet) is the build deck.I'm really curious to hear how you like the Xeta, and me as well. Like you, I love the vapeshell. My only complaint was the af plastic thingy, hated it. But I just put an o ring on there that reduces it by about 1/2, and I find it really hard to think I will like the Xeta better, but man if I do.......
Sent from my SM-G920R4 using Tapatalk
My last two builds in my vapeshell have been spot on at 0.7 ohms.Probably a stupid question, but that is my forte sooo......
Do BB just naturally read ohms high? I have put a lot of my standard builds in them, both SXK and BB, and all of them read high. Even when I use a Nauty coil or Nord, high. Not really a big deal, I can adjust my wraps, just wondering.
Sent from my SM-G920R4 using Tapatalk
Hmm, I have only used the standard nut. Maybe I need to tighten it more, but I am a bit scared of over tightening?My last two builds in my vapeshell have been spot on at 0.7 ohms.
If i use an 0.5 EUC coil, sometimes they do jump up to 0.6.
I've also noticed that i get a better reading when using the standard 510 nut as compared to an integrated drip tip.
Hmm, I have only used the standard nut. Maybe I need to tighten it more, but I am a bit scared of over tightening?
Sent from my SM-G920R4 using Tapatalk
Probably a stupid question, but that is my forte sooo......
Do BB just naturally read ohms high? I have put a lot of my standard builds in them, both SXK and BB, and all of them read high. Even when I use a Nauty coil or Nord, high. Not really a big deal, I can adjust my wraps, just wondering.
Sent from my SM-G920R4 using Tapatalk
I don't have a MF Bridge anymore but I do have two of the SXK bridges. I like the SXK bridge now that it fits the Drizzle coils. I actually prefer the design over the MF bc it allows for more juice capacity and it has less pieces. My only issue is the little plastic AFC rings that fit on the bottom of the coil doesn't restrict it enough for my taste and it's a bitch and a half to position once you have it on the coil. If you try to pull it off again it will pull the pin out of the coil head and you run the risk of screwing up the leads on the wire. If you can get past that you can use it with a MTL DryPlug that will help tighten it up a bit, though.Anyone here have a MF bridge full kit they're not using? How does it compare to the SXK MTL kit?
According to Haku these prices are set low.
View attachment 148009
when you know the Circumference: A = C2 / 4πA = π r2
I call shenanigansI saw that earlier this morning...
What is retarded is regardless of wanting a vanity item, you still have to pay $7.90 or whatever they charge think its $10 to ship a replacement part.
It's really bad tact for them to charge that... and there is no convincing me its justified.
Guys, we need to prowl the other threads and pull some more people into this rabbit hole.
So we have more people to buy our stuff lol.
Sent from my SM-G950U using Tapatalk
Nice! I believe they are the same thing. There's a few people here that use them so they'll chime in soon.Your wish is my command.
I stumbled upon the bb thread at the other forum and ended up here. Have 2 sxk bb 60w dna incoming. Also Xeta, spare boro and A-tanks, panels.
Plan to set up the Xeta for DL and the other for tight mtl with drop in coils. Got a couple pointers from brewbear. What do you all think of this for a mtl bridge?
https://modfactory.ecwid.com/#!/BilletBox/c/22155282/offset=0&sort=normal
It takes mini euc coils. Are euc mini and drizzle the same thing? I was gonna try the mini euc 1.3 ohm.
Hoping to learn a ton from you lot.
cheers
The Xeta is also great for tight MTL. I just ordered a second one to try for DTL. Some of the other guys have a lot more experience with the subohm setups than I do..
Plan to set up the Xeta for DL and the other for tight mtl with drop in coils.
cheers
Yep I can confirm that the Drizzle coils and Mini EUC are the same thing. That new Mod Factory Bridge looks nice... it used to be an add-on called the Full Kit/MTL Kit to use with the normal EUC bridge they made previously. That allowed you to use the same bridge for the larger coils or the mini-Drizzles.Your wish is my command.
I stumbled upon the bb thread at the other forum and ended up here. Have 2 sxk bb 60w dna incoming. Also Xeta, spare boro and A-tanks, panels.
Plan to set up the Xeta for DL and the other for tight mtl with drop in coils. Got a couple pointers from brewbear. What do you all think of this for a mtl bridge?
https://modfactory.ecwid.com/#!/BilletBox/c/22155282/offset=0&sort=normal
It takes mini euc coils. Are euc mini and drizzle the same thing? I was gonna try the mini euc 1.3 ohm.
Hoping to learn a ton from you lot.
cheers