YesDrag is regulated correct...
Sent from a very cloudy room
I’m downloading the coil builder for my iPhone. I’m not sure what ohms. I just feel like the rda maybe better with dual coil. I bought the spool and only seem to build .15 ohms for some reason.What phone do you have? Android has vapetool.. will help alot. What ohms do you want?
Sent from a very cloudy room
What phone do you have? Android has vapetool.. will help alot. What ohms do you want?
Sent from a very cloudy room
I’ll check it out but seems faster and easier from experts. I tried making a 6 wrap dual and it said ohms was to low.So where do you wanna be? On my regulateds id run like a .3
So do like 7 wraps and after pack's it'll go close to .3
Check out that app if on android. It'll be your best friend
Sent from a very cloudy room
Dang. I don’t even think it’ll fit in the rda with 10 wraps and cotton. Lol what wire are you using?Stainless steel takes a lot of wraps.. I think 10 raps will be way too much on that and it'll bring you to wear or less you want to be
Sent from a very cloudy room
Exactly..go 7...wrap on a 3 or 3.5 and try it..its regulates so u should be ok...i try to use only ni80Dang. I don’t even think it’ll fit in the rda with 10 wraps and cotton. Lol what wire are you using?
I thought the same bro. But then figured if 5 wraps give .15 only 1 way to go.Does the wire in the picture say 26 and 18 fused with 32? That's weird to me.
Sent from my Nexus 6P using Tapatalk
Strange specs imo...3rd from bottomDoes the wire in the picture say 26 and 18 fused with 32? That's weird to me.
Sent from my Nexus 6P using Tapatalk
OoopsStrange specs imo...3rd from bottom
Sent from a very cloudy room
Yeah it’s mind boggling. I went off a you tubers purchase. But he didn’t show his build. That’s a combo of three types of wires in one. I’m guessing.Ooops
Sent from a very cloudy room
i got a bonza rda and a drop rda. I can’t figure out what build or how many wraps to make to use as dual coil. I been trying 5 wraps and it ohms out at .15. I’m using the Vandy Vape spool. Oh and I’m using the voopoo drag mod
Which way is that?I thought the same bro. But then figured if 5 wraps give .15 only 1 way to go.
Sent from a very cloudy room
.15 for one coil. I tried 6 wraps and ohm came out to low to read.Is that .15 for one coil?
Try 6 wraps around a 3mm diameter coil rod, but even 5 wraps dual coil will be high enough resistance to fire on a Drag I believe
Does the wire in the picture say 26 and 18 fused with 32? That's weird to me.
Sent from my Nexus 6P using Tapatalk
No.. dual. I don't use singleIs that .15 for one coil?
Try 6 wraps around a 3mm diameter coil rod, but even 5 wraps dual coil will be high enough resistance to fire on a Drag I believe
I’ll try again when I get home. But is that ohm safe?That's the weird chinese way of measuring flat/ribbon wire
26g is 0.4 mm
18g is. 1 mm
So it's 1x.4 mm flat ribbon claptoned in 32
I thought the Drag can fire down to .05 - you may have a short (coils touching sides or top of the RDA) if your single coil is .15 ohms, because half that is .075 ohms which should fire
.15 for one coil. I tried 6 wraps and ohm came out to low to read.
I’ll try again when I get home. But is that ohm safe?
No.. dual. I don't use single
Sent from a very cloudy room
Lol. Yes it is a single coil reading at .15. I used a 3mm rod and tried 6 wraps and 5 wraps. I think the 4 wraps I can do dual.If it fires on your mod, and your batteries are good (brand names, check out Mooch's recommended 18650 list if you havent yet), then it's safe.
Was asking OP
One BIG ASS coil. Lol.Try 7 wraps around 3.5mm for dual coils, or use one big ass coil in the middle
Your wire has a very low resistance, I'd recommend n80 (nichrome) or kanthal, and recommend fused claptons (two round cores, reads like 2x28 or 3x28, etc) rather than claptoned ribbon
Ahh ok. I was wonderingThat's the weird chinese way of measuring flat/ribbon wire
26g is 0.4 mm
18g is. 1 mm
So it's 1x.4 mm flat ribbon claptoned in 32
I thought the Drag can fire down to .05 - you may have a short (coils touching sides or top of the RDA) if your single coil is .15 ohms, because half that is .075 ohms which should fire
Ooops... but now you know for future referenceIf it fires on your mod, and your batteries are good (brand names, check out Mooch's recommended 18650 list if you havent yet), then it's safe.
Was asking OP
One BIG ASS coil. Lol.
Less wraps will lower resistance.Lol. Yes it is a single coil reading at .15. I used a 3mm rod and tried 6 wraps and 5 wraps. I think the 4 wraps I can do dual.
Sorry was to busy to put the 6 wrap in.Well?
Sent from a very cloudy room
7 wrap. 16 ohm. I had a 5 wrap and it ohm at .15. I don’t get it. I know if I put dual 7 wrap it’ll go .08 ohm. Still safe?Well?
Sent from a very cloudy room
7 wrap. 16 ohm. I had a 5 wrap and it ohm at .15. I don’t get it. I know if I put dual 7 wrap it’ll go .08 ohm. Still safe?
I heat the coil up and it goes up to 21 and back down to 16Is that before you ever heat up the coil? It will probably go up a bit after you heat it and work out the hot spots
.08 is still okay for the Drag, though
That's how SS works. Some people don't like it for TC because of that reasonI heat the coil up and it goes up to 21 and back down to 16
You don't like it?.18 is nice on the Rage.. on my parrelels i run .1'sI heat the coil up and it goes up to 21 and back down to 16
I heat the coil up and it goes up to 21 and back down to 16