steam crave aromamizer supreme

Discussion in 'General Rebuildable Discussion (RTA/RBA/RDA)' started by Plusewolf, Jul 29, 2016.

  1. Plusewolf

    Plusewolf New Member

    Blog Posts:
    0
    Joined:
    Jul 29, 2016
    Messages:
    14
    I have the steam crave aromamizer supreme and recently it as been giving me problems, I'm hoping some one can me fix it.

    Problem: on the part u screw into ur mod, there's the standard screw in the middle. Now I'm not sure if striped or it's the wrong screw. But in order to get to work I have to play around with screw, u know lossening it and tightening it, till I get it in the right place. I am only able to get a few hits before having to playing around with the screw agin

    My mod is the reuleaux rx200s
     
  2. nightshard

    nightshard It's VG/PG not PG/VG VU Donator Gold Contributor Member For 3 Years

    Blog Posts:
    0
    Joined:
    Oct 17, 2014
    Messages:
    3,731
    The Supreme 510 is quite long and even with the screw tightened all the way in it's still supposed to make a connection with the RX200S 510 connector.
    Maybe the problem is with the mod connector and not the tank pin.
    Check the pin inside the mod 510 connector, to see if it's stuck all the way in/loose/broken.
    Wismec/Joyetech 510 connectors are not the best.
    Try the mod with a different tank and the tank with a different mod to figure this out.

    Also do the obvious and check that your build not loose in the deck and that the positive post is not loose in the deck from all the playing around with the positive screw.
     
    Last edited: Jul 29, 2016
    Heartsdelight likes this.
  3. Plusewolf

    Plusewolf New Member

    Blog Posts:
    0
    Joined:
    Jul 29, 2016
    Messages:
    14
    I don't believe it the mod. my mod fire my fuel fell and vape geek eagle with no problems. I have even tested my steam crave aromamizer supreme on my friends mods and it still as problems.
    I will check to c if the build is tight later tonite and thank u for advice
     
  4. Scratch88683

    Scratch88683 Bronze Contributor

    Blog Posts:
    0
    Joined:
    Aug 22, 2015
    Messages:
    345
    not positive but it could also have something to do with the insulator on the supreme. i never had it happen to me but i know other people have had insulators break on their rta's and rda's and it will cause act screwy. again not positive if thats your problem. honestly if your positive its the supreme and not the rx200s you should just buy a replacement deck it will give you a new pin and insulator if theres a problem with the supreme it has to be coming from the deck so it would basically cover everything that could cause the issue by replacing the deck. unless the problem is your rx200s 510 connector and if thats the case its a much harder problem to fix. its not easy to change the connecter. i would just order a new deck and go from there it costs like $14.00 from steam crave http://shop.steamcrave.com/supremerdtadeck_p0924.html
    and it costs $9 from fasttech if you want to wait like 2 months https://m.fasttech.com/product/4564900-diy-authentic-steam-crave-aromamizer-supreme-rdta
    ive ordered replacement glass from steamcrave and it came within a week or 2. they ship using that combo ups and usps ststem which is terrible with tracking information but it does come within a week or 2 depending where you live.
    i wouldnt bother with fasttech unless you really want to save the $5.



    also like the above poster said make sure your build is good and tight and not touching the side of the rta that could very well be your problem as well.
     
    mero16 likes this.
  5. Plusewolf

    Plusewolf New Member

    Blog Posts:
    0
    Joined:
    Jul 29, 2016
    Messages:
    14
    thank u both for advice, the steam crave aromamizer supreme is my first rdta, I just picked up the eagle as sorta a replacement for it, but sadly I don't care much for the eagle. I really like steam crave aromamizer supreme and my budget is very tight, so if possible I'd like to save the steam crave aromamizer supreme
     
    mero16 likes this.
  6. nightshard

    nightshard It's VG/PG not PG/VG VU Donator Gold Contributor Member For 3 Years

    Blog Posts:
    0
    Joined:
    Oct 17, 2014
    Messages:
    3,731
    I can relate, the Supreme is still my all around favorite RDTA, even now after using it for several months.
     
    mero16 and Heartsdelight like this.
  7. Scratch88683

    Scratch88683 Bronze Contributor

    Blog Posts:
    0
    Joined:
    Aug 22, 2015
    Messages:
    345
    i liked the supreme a lot and still think its one of the best mainly because i never had leaking issues and it gave a great vape, the only thing i would have changed was adding a little more airflow. i ended up using the boreas for a while after that but i could never get it perfect to where it wouldnt leak when left on its side. then i bought the griffin 25( i used the original griffin all the time before the supreme came out) and ive been using the griffin 25 ever since. i like to have a go to tank and a go to rda. also i went to look at my supremes pin and insulator when i was commenting on your post and i have no idea where i put it i was gonna try it again since its been a few months but i cant find it. i havent tried the eagle but i didnt hear great things about it. but like i said i really love my griffin 25. btw i consider an rta and a rdta the same thing they are both tanks just different ways of wicking. rdta was just a way for companies to make it sound like something new
     

    Attached Files:

    Heartsdelight likes this.
  8. Plusewolf

    Plusewolf New Member

    Blog Posts:
    0
    Joined:
    Jul 29, 2016
    Messages:
    14
    To be honest I consider the steam crave aromamizer supreme a true rdta and the others just rta. Cause with the steam crave aromamizer supreme as the juice door and it build isn't submerged in juice
     
  9. Heartsdelight

    Heartsdelight Gold Contributor Member For 2 Years

    Blog Posts:
    0
    Joined:
    Sep 25, 2015
    Messages:
    3,244
    I've had good luck with Fasttech as long as it's in stock. About 10 days average to USA.
     
  10. Scratch88683

    Scratch88683 Bronze Contributor

    Blog Posts:
    0
    Joined:
    Aug 22, 2015
    Messages:
    345
    it depends on if they have the item in one of their u.s location. its hard to figure out if they do or dont in my experience most items aren't. ive ordered from them atleast 10 times and every item took between 1-2 months. ive even heard some people say it took 3 months but i think thats pretty rare. but if they do have it in a u.s warehouse it will come normal shipping times.
     
  11. Heartsdelight

    Heartsdelight Gold Contributor Member For 2 Years

    Blog Posts:
    0
    Joined:
    Sep 25, 2015
    Messages:
    3,244
    They don't have a USA warehouse as far as I know. But as long as the item is in stock & states it ships out next day. It does, haven't had any any issues. Preorders are another thing it can take a long time depending on the manufacturers shipping to them. For example I ordered the IJoy Limitless Plus Rdta last Friday night , by Saturday morning it was shipped. It all depends if it's in stock. I'm not trying to sway your opinion, but in my experience it good, save money on new items with code "MAP" change your mind you can cancel your order before they package with 1 click, money is back in your account by the next day.
     
    Nevweezy likes this.
  12. Wingsfan0310

    Wingsfan0310 Gold Contributor Member For 3 Years

    Blog Posts:
    0
    Joined:
    Jul 15, 2014
    Messages:
    4,229
    He must be thinking of Gearbest, they have a warehouse in the USA.

    I agree if FT has the item in stock and you select USPS E-Packet as you shipping option (free on orders $20 and up) it's 10 days to 2 weeks to the USA.

    Cheers,
    Steve
     
    Heartsdelight and Nevweezy like this.
  13. Plusewolf

    Plusewolf New Member

    Blog Posts:
    0
    Joined:
    Jul 29, 2016
    Messages:
    14
    Okay so at last I got around to doing some thing about the steam crave aromamizer supreme. Now what is the insulater. Now if I remove the bottom piece, my mod will read it but if I put in on, my mod won't read it. Not sure what it's called, but it's the part that u screw on after u put the build deck back in
     
    Last edited: Jul 30, 2016
  14. Wingsfan0310

    Wingsfan0310 Gold Contributor Member For 3 Years

    Blog Posts:
    0
    Joined:
    Jul 15, 2014
    Messages:
    4,229
    This might sound like a dumb question but the deck has notches so it only fits one way in the base (seats in). Are you sure you hace the notches lined up with the holes (is it seated all the way in)?

    The Wismec/Joyetech 510 connectors are notorious for giving atomizer short because in some (not all) the pin gets pushed down yo far and either won't bounce bach up or damages the 510 connector altogether. Do you have another mod to try your Supreme on? I'm leaning towards the it's on the RX's end. Take a Q-Tip and gently push on the RX's 510 pin, is it moving up and down freely?

    Cheers,
    Steve
     
  15. Plusewolf

    Plusewolf New Member

    Blog Posts:
    0
    Joined:
    Jul 29, 2016
    Messages:
    14
    Yes my mod will happily fire my eagle and fuel cell with no problems.

    Thanks for ur help, but it seems the steam crave aromamizer supreme is garbage
     
  16. Wingsfan0310

    Wingsfan0310 Gold Contributor Member For 3 Years

    Blog Posts:
    0
    Joined:
    Jul 15, 2014
    Messages:
    4,229
    I have 6 Supremes and they are far from garbage. They are the best built, most accurate (stable resistance) of any RTA I've ever tried/owned. I was asking if you have a different mod than the RX to try the Supreme on. If you look you will see that the RX is known to have problems with showing atomizer short, etc. I think you have the garbage thing reversed!
    http://vaping360.com/wismec-reuleaux-issues/
     
    Last edited: Jul 30, 2016
  17. Scratch88683

    Scratch88683 Bronze Contributor

    Blog Posts:
    0
    Joined:
    Aug 22, 2015
    Messages:
    345
    i'll second that the supreme is very well made and ive dropped it multiple times only thing that happened was I broke the drip tip (which sucked i liked the tip) if anything it sounds like you got a faulty deck or something your doing is wrong or something happened to the deck. theres plenty of poorly made rta's but the supreme definatly isnt one of them i will say its over priced though. that was my only complaint. also i wasnt talking about gearbest, i dont think ive ever ordered from them(might have ordered a clone mech mod from them once cant remember). i thought for some reason i saw on fast techs something about u.s warehouses but i guess im wrong. i have heard of that epacket thing before but i never tried it. Most things ive ordered from them i didnt really care how long it took for them to come(mostly colored glass tanks, and i couple of clones that i didnt care much about just wanted to try). I can say for certain that steamcrave has a warehouse in upstate new york and they will ship priority mail(think they charge like $2 if you want priority).
     
    mero16 and Deucesjack like this.
  18. Plusewolf

    Plusewolf New Member

    Blog Posts:
    0
    Joined:
    Jul 29, 2016
    Messages:
    14
    Sorry I should have been more clear, I didn't mean the steam crave aromamizer supreme was garbage it self. I meant I thought I couldn't fix the problem, so I assumed it couldn't be fixed and thus if was it would be garbage

    But I fixed the problem by trading the rx for fuchia mod and now it works great and for the eagle all it needed was to take out the pre-made coils and build my own coils and dam is it awesome and it rips great. I have a 26/32 Clapton kanthal wire 25 dia, 7 wraps and its ohms out around 1.20 on the single coil deck and it chucks coulds like it as comp wire in it and vape the new mod between 50-60w

    Normally I don't vape comps cause I don't like hot builds, but with the eagle I'm more willing to try more vape comps
     
    Last edited: Jul 30, 2016
    Scratch88683 and Heartsdelight like this.
  19. Scratch88683

    Scratch88683 Bronze Contributor

    Blog Posts:
    0
    Joined:
    Aug 22, 2015
    Messages:
    345
    yea those rx's really have shitty connectors. my pin is noticably pushed in but luckily still works without issue but im sure one day it will stop working. glad you fixed your problem!
     
  20. CashNVape

    CashNVape Gold Contributor Member For 1 Year

    Blog Posts:
    1
    Joined:
    Aug 8, 2016
    Messages:
    3,120
    with my smok alien, 7ml supreme I was able to get 212, 3 second puffs. watt mode at 75w with 2 married samsung 25Rs before tank emptied. batteries have about 35% left

    Stuff for sale...Inquire within.
     
    Heartsdelight likes this.
  21. Deucesjack

    Deucesjack VU Donator Platinum Contributor Member For 2 Years ECF Refugee

    Blog Posts:
    0
    Joined:
    Sep 8, 2015
    Messages:
    7,978
    I have 4 Supremes acquired during the Yeti vape sale. All 4 show no atomizer on my Reuleaux RX 200 and my Reuleaux DNA. They work on every other mod I own except those two. The 510 on the Reuleaux's is indeed truly a piece of shit.

    Sent from my SAMSUNG-SM-G900A using Tapatalk
     
  22. SirRichardRear

    SirRichardRear AKA Anthony Vapes on Youtube VU Donator Diamond Contributor Member For 1 Year Reviewer

    Blog Posts:
    0
    Joined:
    Jul 8, 2016
    Messages:
    11,571
    i really wish people would stop recommending those here lol. more trouble then they are worth. I cringe everytime i see someone who has an rx and a fuchai 213 as their mods. like WTF where is their advice coming from. Throw in an IPV6 and you have the holy trinity of lies and shit quality lol. It's not a big deal for people who have a ton of mods, but when people are depending on them and not really sure what they are doing, it sucks to deal with issues.
     
  23. CashNVape

    CashNVape Gold Contributor Member For 1 Year

    Blog Posts:
    1
    Joined:
    Aug 8, 2016
    Messages:
    3,120
    I'm so glad I didn't get a rx200s or any of those devices. I kept my self from one even seeing them at a great price it's not worth the troubles!

    Stuff for sale...Inquire within.
     
    SirRichardRear likes this.
  24. SirRichardRear

    SirRichardRear AKA Anthony Vapes on Youtube VU Donator Diamond Contributor Member For 1 Year Reviewer

    Blog Posts:
    0
    Joined:
    Jul 8, 2016
    Messages:
    11,571
    this on is similar to an rx2/3 (without the 3 battery option) and feels much better built. i'm liking it so far and was only 31 bucks.
    [​IMG] [​IMG]
     
    Heartsdelight likes this.
  25. Deucesjack

    Deucesjack VU Donator Platinum Contributor Member For 2 Years ECF Refugee

    Blog Posts:
    0
    Joined:
    Sep 8, 2015
    Messages:
    7,978
    I bought both my Reuleaux's on preorder. Tbh though I love the form factor of them and when the 510's totally shit the bed I'm more than likely going to send both out for a new Fat Daddy 510 and rewiring. I know it's like putting $6000 rims on a $12000 Honda but I really like both mods.

    Sent from my SAMSUNG-SM-G900A using Tapatalk
     
    Last edited: Dec 13, 2016
    SteveZ, DP2Raja and Heartsdelight like this.
  26. Whiteshep

    Whiteshep New Member

    Blog Posts:
    0
    Joined:
    Mar 16, 2016
    Messages:
    45
    Love my supremes best tanks i've ever had and use one very happily on an rx200 not a single problem in six months I've noticed differences in build quality amongst the three rx's i own not big things but there nonetheless. Obviously they don't stack up to my ml class in any regard but they have been solid mods accepting their limitations main one being 430 ss is useless at it's proper tcr. They will be relegated to backup mods soon as have two triade dna250's coming.
     
    mero16, Heartsdelight and CashNVape like this.
  27. CashNVape

    CashNVape Gold Contributor Member For 1 Year

    Blog Posts:
    1
    Joined:
    Aug 8, 2016
    Messages:
    3,120
    hey man people do that! I've seen some real rust buckets in the cities but they got 10 thousand dollar rims on it so it's a G ride yo! lol
    who offers repair on the RXs?

    audaces fortuna iuvat
     
    Heartsdelight likes this.
  28. SirRichardRear

    SirRichardRear AKA Anthony Vapes on Youtube VU Donator Diamond Contributor Member For 1 Year Reviewer

    Blog Posts:
    0
    Joined:
    Jul 8, 2016
    Messages:
    11,571
    some dude on facebook. charges like 60 bucks and upgrades the wiring and 51- pin. personally whats the point of buying a 40 dollar mod then spending 60 bucks to make it good lol. for 100 bucks you can actually by a really good mod
     
    CashNVape likes this.
  29. Deucesjack

    Deucesjack VU Donator Platinum Contributor Member For 2 Years ECF Refugee

    Blog Posts:
    0
    Joined:
    Sep 8, 2015
    Messages:
    7,978
    This guys supposed to be the best but he has like a 2 week back up.

    https://www.facebook.com/VapinArchitect?ref=ts&fref=ts&__nodl

    Sent from my GT-N8013 using Tapatalk
     
    Heartsdelight and CashNVape like this.
  30. DP2Raja

    DP2Raja Bronze Contributor Member For 1 Year ECF Refugee

    Blog Posts:
    0
    Joined:
    May 2, 2016
    Messages:
    400
    I have 3 RX200 mods. 1 went south (510 crap) within 3 weeks, the other 2 have been solid and used daily for about 5 months. I bought 2 Fat Daddy 510s to replace them myself. But I had already thrown the bad Rx200 away. So far the other too have worked great. But I expect they may fall to the curse of the 510 some day. Until then, they are work horses. But I only use power mode. not a TC guy.
     
    Last edited: Dec 18, 2016
    Heartsdelight likes this.

Share This Page

Close This Message