Want to build two coils that isn't going to
A use up all the juice in 30min or less,
B use less battery / wattage: ideal wattage is about 50w or less
Any suggestions?
The wire I have is:
SS316 24g, 26g
Kanthal 26g
Build around .5 - .8 Ohms basic coils will do thatWant to build two coils that isn't going to
A use up all the juice in 30min or less,
B use less battery / wattage: ideal wattage is about 50w or less
Any suggestions?
The wire I have is:
SS316 24g, 26g
Kanthal 26g
I have 32g kanthal on the way but that's for some Clapton build. I'm sure that's way too thin for some lower power builds.there is no such thing as a battery saving byuild. Mainly because the wattage you run determines the battery longevity. Basically at 50watts a .5ohm coil will use the battery at about the same rate as a .2 coil. Which coil uses the battery faster will be determined by which coil used more wire and has the longer ramp-up time..
I would suggest using steam-engine.org to model some lower wattage builds. Granted to get where you want to go you might need different wire. Since the thinnest you have is 26 awg, your kinda limited to .5ohm or lower builds, you could go higher.. But that would just increase ramp time and hurt battery life because thicker wire high ohm coils tend to need more wattage to perform than low ohm coil need. Me I would either do .5ohm with the 26SS or the 26K at around .8-1ohm, but then I also comfortably vape at 25watts or less. Current builds .34ohm 2x28SS twisted running at 18watts in TC at 400f and .7ohm 28SS running at 21watts in TC at 400f. Both in KFL tanks.
I have 32g kanthal on the way but that's for some Clapton build. I'm sure that's way too thin for some lower power builds.
Sent from my SM-G900V
Yeah..... you need a lot of power and batteries to heat up all that wire......The dude at the vape shop almost shit himself when he saw my dna Reuleaux was set to 177.7 watts.
Double twisted 24ga titanium duals @ .05, temp controlled to my liking.
Lots of coil mass = lots of powah.
Um, if you twist it, it is no longer 32g you're vaping inNo its not. Is my prefered gauge for twisted builds down to about .5ohm... even lower if you do multi coil builds or use stainless.
Sent from my SCH-I605 using Tapatalk
Not if you have a leak! LOLBTW it's pretty hard to drain that capacity in 30 minutes.
Thanks. The best explanation, i think.there is no such thing as a battery saving byuild. Mainly because the wattage you run determines the battery longevity. Basically at 50watts a .5ohm coil will use the battery at about the same rate as a .2 coil. Which coil uses the battery faster will be determined by which coil used more wire and has the longer ramp-up time..
I would suggest using steam-engine.org to model some lower wattage builds. Granted to get where you want to go you might need different wire. Since the thinnest you have is 26 awg, your kinda limited to .5ohm or lower builds, you could go higher.. But that would just increase ramp time and hurt battery life because thicker wire high ohm coils tend to need more wattage to perform than low ohm coil need. Me I would either do .5ohm with the 26SS or the 26K at around .8-1ohm, but then I also comfortably vape at 25watts or less. Current builds .34ohm 2x28SS twisted running at 18watts in TC at 400f and .7ohm 28SS running at 21watts in TC at 400f. Both in KFL tanks.
Best I can do to explain the magic of electricity.Thanks. The best explanation, i think.
Sent from my Redmi Note 4 using Tapatalk