Temp control settings what does everyone use?

[djj624]

I'm on a sigelei 150tc with smok tank 70 joules 500 temp. What about you guys.

Sent from my Nexus 6 using Tapatalk

 

[Valkyrie]

reuleaux dna 200 / kanger subtank plus w/ni 200 occ head...40 watts /450 degrees
yihi sx mini ml / aromamizer w/ni 200 premade pan...44 watts / 450 degrees
reuleaux rx 200 / uwell crown tank w/ dual coil ni 200 occ head / still looking for that good vape on this combination

 

[raymo2u]

Snow Wolf Crimson with TFV4 TF-N2 Coils: 70W@600°F
Snow Wolf Crimson Mini with Vaperesso Target NI200 Ceramic Coil: 75W@520°F
I love TC because the Weather if fricken cold here and Max VG gives burned hits left and right before I found how great TC was in the Cold....No more dry hits and I can pull for as long as I want when outside in the cold!

 

[Wingsfan0310]

I use DNA200 mods for TC. I've also used an IPV3 Li for TC before the DNA200's. I mainly use Billow V2's or a Bellus (dual coil RTA's) at 450F and normally between 25-35 watts (preheat set between 80-100 watts for 1 second). I've found It doesn't take a lot to heat up 28ga Ni200.

 

[Jaaxx]

I'm normally 420-470. In my mind the key is having a device with wattage adjustable in TC mode. The wattage is essential as that will determine how quickly TC will "kick in."

 

[africamonk]

Kbox 120 / 485F / 317 SS / Crius / no wattage control on it.

 

[skt239]

Snow Wolf Mini, Crown Ni200 - 480 degrees, watts are automatically applied.

Evic VTC mini, Herakles Plus SS coil - 500 degrees, 55 watts.

RX200, Starre Tank w/Aspire SS coil - 450 degrees, 45 watts.

 

[SOC]

Sig 150W TC, 60 W, 500 F. Crown or Starre Pro, Ni200.

 

[f1r3b1rd]

DNA200- all 24g SS
petri rda
50W, 440 DEGREES 65W PREHEAT 8.5 PUNCH
aeolus v2 same setting for obs crius
45W, 460 DEGREES, 60W PREHEAT 8.5 PUNCH
hurricane rta
24W, 450 DEGREES 30W PREHEAT 7.5 PUNCH

SXMINI M CLASS-all 24g ss
triton coil 0.4 OHM COIL
48W, 470 DEGREES
Aeolus lite
50W, 460 DEGREES

 

[wally]

I stick 60 / Melo 2, Ti, 480 to 520 Deg., 30 watt. Temp settings pending on mood.

 

[centella4u]

430-450 F for my Ti01 build RH @ 45-50 watts on RX200 & IPV 3Li
440 F for my SS build nobunaga @ 50 watss also on my DNA200
Others, depending on my mood at that moment.


Sent from my iPad using Tapatalk

 

[dre]

Sx mini ml 480°f usually around 32j with 24g ti single coil. It preheats from 50j down to 32j within 2 seconds with the software.

Sent from my Droid Turbo 2 using Tapatalk

 

[Dreamonvaper]

Modified Kanger rba (holes opened-up to 3mm), 5 turns of 26 ga. 316L SS wire at 0.4 ohms, loose pancake cotton, Kanger Toptank mini in TC mode at 460F on KBOX 200, 35/65 PG/VG juice. Only leak I had is screwing top down on a full tank--hydraulic pressure forced juice into the base. Other than that, no leaking at all, no spitting whatsoever at that temperature, fairly reasonable draw and good cool vapor with amazing flavor. To confirm what has already been said, wicking is critical and it took me 3 attempts before I got this right. A point on the SS in TC, it takes a few ml of vaping to break this setup in and really saturating the wick when priming seems to be crucial. I start vaping at 360 and work up to my target in increments of 10 degrees. Works beautifully.