Become a Patron!
mech mods
- Thread starter mokeife
- Start date
parallel or series?
i have a few parallel mods that are pretty sweet but my collection of series just keeps growing and growing.
pretty huge difference in how they perform.
have you any experience is mechanical mods?
Sent from my SM-N920T using Tapatalk
i have a few parallel mods that are pretty sweet but my collection of series just keeps growing and growing.
pretty huge difference in how they perform.
have you any experience is mechanical mods?
Sent from my SM-N920T using Tapatalk
i dont know which is safer?what are the differences in how they perform? does one hit harder than the other?no i do not have any experience with mech mods all mine are regulated. i have been studying ohms law. the mod i was looking at is http://www.evcigarettes.com/cci-edition-smw-parallel-mechanical-box-mod-by-smw-mods
Last edited:
Personally wouldn't have gone series off the bat but some nice head room with 26650 batteries but please make sure you fully understand ohm's law when it comes to building series coils. Also make sure you have a nice big dripper or RTA for it because your coils are going to be a bit big
i just tried my regulated mod (rx200) at 235 watts with a twisted messes dripper and any hit i take longer than a second it tastes extremely burnt. i have a 24 gauge 7 wrap build ohming out to .32 ohms 3mm wrap...what am i doing wrong? yes i have 30 amp cells...can you just not go that high with a regulated device?
Last edited:
SirRichardRear
AKA Anthony Vapes on Youtube
VU Donator
Diamond Contributor
Member For 3 Years
Reviewer
vaping at 235 watts is what you are doing wrong. try like 50-60 watts
i was doing a test some people are saying they vape .3 ohm coils in a series box which comes out to about 235 watts which i cant figure out how their doing it without massive burnt hits i normally vape this build at around 90-120 watts
SirRichardRear
AKA Anthony Vapes on Youtube
VU Donator
Diamond Contributor
Member For 3 Years
Reviewer
it really depends on your build. the people doing that know exactly how they need to build. But to be honest unless you are competing in a cloud competition it's pointless.
i know i could hit that with a clapton build however this is almost the exact build that someone told me they use on their series mech mod only with 1 extra wrap im just curious as to what their doing differently
If you want to tame it, build coils with a lot of mass. And that extra wrap would put you at a safer ohm that what you're doing. Start off with a .6 build and tweak it as you see fit
I won't build below 0.5 on a series Mod. My usual build is between 0.7-0.9.
Sent from my Nexus 6 using Tapatalk
do you know how to build? do you have an ohm reader?
thats a killer first mech, a lot of power, can be bad if not careful.
i find mini fused claptons (28g and higher) to be best for series, for me anyway. 8 to 10 wraps dual coil depending on material used around a 3mm bit.
thats my go to, anyway.
dont let yourself try to drift into trying to copy what you see, a lot of people with a lot of experience like to take chances because they know exactly what theyre doing, the risk theyre taking and what to look out for when things start going south.
either way, enjoy your vape, be safe and good luck. if any questions a lot of dudes here know a lot of stuff and could help you resolve most issues you may run into.
out of curiosity, dont know if its been mentioned, which 26650 cells did you buy and from where?
Sent from my SM-N920T using Tapatalk
thats a killer first mech, a lot of power, can be bad if not careful.
i find mini fused claptons (28g and higher) to be best for series, for me anyway. 8 to 10 wraps dual coil depending on material used around a 3mm bit.
thats my go to, anyway.
dont let yourself try to drift into trying to copy what you see, a lot of people with a lot of experience like to take chances because they know exactly what theyre doing, the risk theyre taking and what to look out for when things start going south.
either way, enjoy your vape, be safe and good luck. if any questions a lot of dudes here know a lot of stuff and could help you resolve most issues you may run into.
out of curiosity, dont know if its been mentioned, which 26650 cells did you buy and from where?
Sent from my SM-N920T using Tapatalk
thanks for the post yes ive been building for about a year now ive done alot of builds on my mutank now im using a twisted messes dripper. im using 7 wrapps of 24 gauge around a 3mm bit, ohms out at about .32 . ive been studying ohms law alot and i pretty much have it down. and i didnt mention im not using the 26650 atleast yet im going to be using the adaptor sleeves with lg hb6 till i save up and get some 26650s
Last edited:
how many ohms do those 28 gauge fused claptons come out to?