Okay I just bought a mvp4 & im using a baby beast. My old vape didn't have the control settings so I'm so counfused.. what should I put it on? Ni ti ss w????
Become a Patron!
need help!!!
- Thread starter Kaay_chianne
- Start date
SMOKIE
THE MODFATHER
Staff member
VU Senior Leadership
VU Senior Administrator
Senior Moderator
VU Donator
Platinum Contributor
VU Live Leadership
Show Host
Reviewer
Vape Media
VU Live Host
Member For 5 Years
Did you read the instruction booklet?
Depends on the coil you use.
Ti = Titanium 1 Wire (Temp Control Only)
Ni = Ni200 Nickel Wire (Temp Control Only)
SS = Stainless Steel Wire (Temp or Regular Variable Wattage Mode)
W = Wattage Mode, which can use Kanthal A1 coils (most coil heads are made from Kanthal), NiChrome (similar to Kanthal but softer and heats up quicker), or Stainless Steel.
With TC or VT (Temp Control/Variable Temperature), you have to set the system to the appropriate type of wire (ie Ni, Ti, or SS), then if you can set your watts, and then adjust your temperature. TC/VT control will ramp up to set watts, then reads the resistance of the coil as it is firing, as wire heats up, its resistance increases, this is how the mod guesses the temperature of the coil, once the set top temperature is reached, the system adjusts the wattage up and down repeatedly to maintain the temperature set.
Variable Wattage only mode, start lower watts, prime your coil, fill and assemble the tank, then take short puffs, after 20 to 30 minutes, bump the wattage up a bit, rinse and repeat until you either hit that "WOW" flavor and throat hit, or if you start getting a harsh hit, back the wattage down a couple steps, that will be the max watts for that coil. VT/TC will follow this same formula with the temp setting, its all dependent upon your flavor pallete, not any one all do all silver bullet setting for everyone, just a basic guideline.
Ti = Titanium 1 Wire (Temp Control Only)
Ni = Ni200 Nickel Wire (Temp Control Only)
SS = Stainless Steel Wire (Temp or Regular Variable Wattage Mode)
W = Wattage Mode, which can use Kanthal A1 coils (most coil heads are made from Kanthal), NiChrome (similar to Kanthal but softer and heats up quicker), or Stainless Steel.
With TC or VT (Temp Control/Variable Temperature), you have to set the system to the appropriate type of wire (ie Ni, Ti, or SS), then if you can set your watts, and then adjust your temperature. TC/VT control will ramp up to set watts, then reads the resistance of the coil as it is firing, as wire heats up, its resistance increases, this is how the mod guesses the temperature of the coil, once the set top temperature is reached, the system adjusts the wattage up and down repeatedly to maintain the temperature set.
Variable Wattage only mode, start lower watts, prime your coil, fill and assemble the tank, then take short puffs, after 20 to 30 minutes, bump the wattage up a bit, rinse and repeat until you either hit that "WOW" flavor and throat hit, or if you start getting a harsh hit, back the wattage down a couple steps, that will be the max watts for that coil. VT/TC will follow this same formula with the temp setting, its all dependent upon your flavor pallete, not any one all do all silver bullet setting for everyone, just a basic guideline.
Yes but I don't understand
The coils are 45-60
SMOKIE
THE MODFATHER
Staff member
VU Senior Leadership
VU Senior Administrator
Senior Moderator
VU Donator
Platinum Contributor
VU Live Leadership
Show Host
Reviewer
Vape Media
VU Live Host
Member For 5 Years
That is the wattage recommend to use on the coil, but does the coil have any other markings like Ni , SS, etc?
As far as I know Smok only only makes Kanthal coils for the baby beast. So you should run it in power or wattage mode.
Sent from my SAMSUNG-SM-G900A using Tapatalk
Sent from my SAMSUNG-SM-G900A using Tapatalk
The coils don't say anything other than that & like 15 with some symbol thing..
0.15 with an "Omega" symbol??
Unless the coil has at the bottom pin a colored gasket, like blue will generally be Ni200 Nickel (dark navy blue or powder blue), Ti gaskets are sometimes red though Kanger and couple others use red for their normal Kanthal heads, as stated above unless a 3rd party coil head for the Baby Beast not made by Smok who makes the tank, the coil head will be Kanthal so thus set it to "W" mode, set the watts to the lowest watts printed on the coil, prime it thoroughly, etc like I posted above to get the coil broken in properly.
Unless the coil has at the bottom pin a colored gasket, like blue will generally be Ni200 Nickel (dark navy blue or powder blue), Ti gaskets are sometimes red though Kanger and couple others use red for their normal Kanthal heads, as stated above unless a 3rd party coil head for the Baby Beast not made by Smok who makes the tank, the coil head will be Kanthal so thus set it to "W" mode, set the watts to the lowest watts printed on the coil, prime it thoroughly, etc like I posted above to get the coil broken in properly.
^^^THAT^^^ = 100% CORRECT
Yep very surprised as well.Check... Wattage mode it is.
I'm surprised there are no SS coils for it.
I hated the TFV4* but this little beast is a completely different animal.
*The 1 I had leaked like crazy.Like literally peed all over my hand at 1 point*
Yes I have the t8 in rn. So I should run it on wattage?
Yes between 60 - 80 watts for best results.
Although you would have done better buying a slightly easier mod to use and a tank that isn't going to blow through 120 ml of e-liquid in a couple days.
Yeah probably
Please don't overindulge a challenged person.Just think... at that rate you might get to learn DIY!