Become a Patron!

Poll : What' your wattage?

What's your most used wattage?

  • 0-25

    Votes: 7 24.1%
  • 25-45

    Votes: 14 48.3%
  • 45-65

    Votes: 3 10.3%
  • 65-85

    Votes: 3 10.3%
  • 85+

    Votes: 2 6.9%

  • Total voters
    29

Vape Fan

_evil twin_
Staff member
Senior Moderator
VU Donator
Platinum Contributor
Press Corps
Member For 5 Years
Each of us will at times use a different power level, but in terms of wattage, what wattage range is your go-to or use the most. If your mech or VV you can still figure it out.
 
Last edited:

inganeer

Gold Contributor
Member For 5 Years
I typically wind my own coils. 26 Guage around a 2.5mm rod. Comes out about 0.7 ohms. Depending on the mod because it varies I run 12 to 15 watts.

Sent from my SM-A716U using Tapatalk
 

Vape Fan

_evil twin_
Staff member
Senior Moderator
VU Donator
Platinum Contributor
Press Corps
Member For 5 Years
I typically wind my own coils. 26 Guage around a 2.5mm rod. Comes out about 0.7 ohms. Depending on the mod because it varies I run 12 to 15 watts.

Sent from my SM-A716U using Tapatalk
Im the only one on the pole right now.
Are you able to enter it in the poll? Just checking to make sure I made it correctly :)
 

shawn.hoefer

Gold Contributor
Member For 4 Years
When running dual SS fused claptons in TC mode, I keep the wattage set around 70, and the temp around 450F. When running dual Ni80 fused claptons, I keep the wattage around 85. When running mesh RTAs, I'm happy around 60 watts. When running using a pod system (dotAIO with RBA and a roundwire build, BB with an RBA and a roundwire build, or a VooPoo Drag X with the SMRT kit), I stay around 30 watts... maybe up to 40...

Sent from my SM-N986U using Tapatalk
 

Vape Fan

_evil twin_
Staff member
Senior Moderator
VU Donator
Platinum Contributor
Press Corps
Member For 5 Years
When running dual SS fused claptons in TC mode, I keep the wattage set around 70, and the temp around 450F. When running dual Ni80 fused claptons, I keep the wattage around 85. When running mesh RTAs, I'm happy around 60 watts. When running using a pod system (dotAIO with RBA and a roundwire build, BB with an RBA and a roundwire build, or a VooPoo Drag X with the SMRT kit), I stay around 30 watts... maybe up to 40...

Sent from my SM-N986U using Tapatalk
I can be under 20 or to about 25 w/ GT4, 45-60 w/ dual RDA, 60-65 w/ Fatality. Most everything else in single coil is usually the 25- 40 range including mesh RTA.
 

5150sick

Under Ground Hustler
Staff member
VU Administrator
Senior Moderator
VU Donator
Diamond Contributor
Press Corps
Member For 5 Years
Mod Team Leader
I'm usually at around 75 watts on the mods,
I think my pod device is like 20 or 25 watts max. lol
 

mreeveshp

Bronze Contributor
Member For 5 Years
I usually build n80 twisted at about .4 and run at about 30-35 watts which is super low for my mod since it goes to 234 watts but I don't care about big clouds I want good flavor and it also has the added benefit of not burning through juice as quick. I have my airflow pretty tight too for better flavor and running higher watts gets it hot really quick. Since I run so low my coils last a long time but I re-wick and clean my coils every 2-3 days sometimes I can push that a little farther but as soon as the flavor drops off too much its time to change

Thanks
mreeveshp
 

Grandpa

Bronze Contributor
Member For 4 Years
I make my coils out of n80 fused clapton wire and Ø3.5mm, # of wraps depending on the device it needs to go in. For a single coil, around .50-.70Ω; for dual coils, around .15-.20Ω. I run my single coils between 30 to 40 watts, and my dual coils between 55-65 watts. I use 100% VG and get clouds but that's not the point. I go all VG because I'm allergic to PG.
 

gopher_byrd

Cranky Old Fart
VU Donator
Diamond Contributor
ECF Refugee
Member For 5 Years
VU Patreon
Most of the time I'm on mech squonks with 0.3 Ohm fused Claptons. So around 50 Watts depending on where the battery is at. On my Hohm Wreckers in TC I have them set to 90 Watts.
 

MyMagicMist

Diamond Contributor
ECF Refugee
Member For 5 Years
I run mech squonks with single coil RDAs exclusively. I use the same build in all of them,
... well perhaps not exact. I run coils in the 0.30 to 0.45 oHm range This lets me run about 25 watts on a mechanical. Might hit higher or lower depending on battery charge, that's average though.

Yeah, yeah, I'm a wimp that likes a cool DL vape. *chuckles* :)
 

Bliss Doubt

Platinum Contributor
Member For 5 Years
9 to 10.5w with a 1.6 ohms coil in an Aspire BVC glassomizer on my eLeaf. 10.5w most of the time, but the range depends on coil age and gurgling. If I get gurgling and spitting, I tip the device upside down with the mouthpiece pressed onto a napkin to let it run out, then back down the wattage, sometimes even lower than 9, and vape until it clears up, then bring the watts back up.

Not at all an unusual routine, I'm sure.

If the coil needs changing, sometimes I bring the watts up to 11 or 11.5 while I'm putting roots into my big chair, until I have to get up due to empty tank, at which time I drain it out and put in a new coil.
 

walton

Gold Contributor
Member For 2 Years
New Member
Reddit Exile
Each of us will at times use a different power level, but in terms of wattage, what wattage range is your go-to or use the most. If your mech or VV you can still figure it out.
my swag at 45w, my gen at 70w i go for flavour not a steam train impersanator.
 

VU Sponsors

Top