Ok, so I have a sig-s on a fuhattan, I had dual 22g 7 wrap coils and it did ok but my battery died constantly, I tried to rebuild the same thing when they got burnt out but couldn't get both sides to fire at the same time. I've got 22 Guage wire and not sure what my best bet would be for a good flavor and good clouds, any advice?
Become a Patron!
Good coil on sig-s with 22gauge
- Thread starter Wyatt9595
- Start date
I rock 2x22K/46N60 6 Wraps on a 3mm Bit as my ADV, Theres almost nothing that can beat it for flavor or warmth and wicking properties...simly amazing. I am currently vaping on a 22k/50N60 build to see what changes but its only slightly different in terms of ramp up and flavor.
Shots of 22K/446N60:
Shot of 22K/50N60:
If all you have is 22g then I suggest you try a Double Barrel Vertical Build with 5 wraps for each barrel on a 2.5mm bit. Do a dual coil and you should have a warm, flavorful, and battery life saving build.
Shots of 22K/446N60:
Shot of 22K/50N60:
If all you have is 22g then I suggest you try a Double Barrel Vertical Build with 5 wraps for each barrel on a 2.5mm bit. Do a dual coil and you should have a warm, flavorful, and battery life saving build.
Right now I'm running with a 4 wrap parallel 22g and it's not doing bad, I just can't hit it the way I'd like, it's a quick hit build and I like a slow smooth hit, I don't have the money for anything else right now so all I have is the 22g kanthal wire, I've got 1/8, 3/32, 5/64 and 3/64 screw drivers I can wrap my coils with, just not sure what my best bet would be
You would need a different gauge wire, in order to get the resistance up. More like a 24g or even 26g. Use http://www.steam-engine.org/coil.asp as a guideline.
He could add wraps or enlarge his diameter to raise his resistance. If he did the double barrel build I suggested he would be around 4.-.6 Ohms.
If the space allows for it, yes.
If the op is asking these kind of questions, I worry about what kind of battery he's using. sounds like he's around .2 pushing close to 20amps or so.
I don't like the sound of "battery died constantly". Plus, he's using one of the cheapest attys out there with delrin insulators instead of peak.
I don't like the sound of "battery died constantly". Plus, he's using one of the cheapest attys out there with delrin insulators instead of peak.
So, where is the advice in that?
Obviously, with a 0.2 Ohm coil build, and assuming the OP is using proper batteries, you probably have ca. 7 Minutes with one battery. Therefore, the battery will "die" rather quick. Thus, a proper advice would be something like, increase the coil(s) resistance, with different gauge wire, in order to increase the battery's "life", before having to re-charge, or switch the battery.
Advise is difficult to give since he gives no battery information.
cheap delrin insulators, such as in the Sig-s, melt causing shorts. I'm assuming he's using cheap batteries since they "die constantly". My good samsungs running .14ohms on a copper manhattan mod don't "die constantly".. My setup certainly doesn't last all day, but I wouldn't expect it to either.
edit... giving any advise using an unknown battery is probably not good advise anyway. Sounds like a newb, so I can't assume he is using a correct battery for his setup. Cheap atty + cheap mod, many times = cheap battery too.
Last edited:
I understand. However, since the OP hasn't blown up his mod (or more) yet, I also assumed he is using proper batteries.
I assume he doesn't have a clue about ohms law, and won't ever be back to this forum to comment about it anywayI understand. However, since the OP hasn't blown up his mod (or more) yet, I also assumed he is using proper batteries.