IT ALWAYS SHOWS "HIGH TEMPERATURE" AND "CHECK BATTERY".
Become a Patron!
HELP! SNOW WOLF 200W
- Thread starter JHVNEVAPE31
- Start date
My suggestion would be to contact the vendor you bought it from and explain what is happening and see what they want you to do. How long have you had it? Is it still under warranty?
Cheers,
Steve
Cheers,
Steve
JUST NOW I EXPERIENCED THIS, ILL TRY TO CONTACT THE VENDOR, ANY OTHER SOLUTIONS?
High Tempature shows when it senses the tank or the 510 connection is past the limits set by its software. It can be caused by using a RDA/RTA with a low resistance build, when temp control seems to run hot and the tank is burning hot, batteries you are using are not rated for the amp draw you are pulling, or a number of other variables.
What Model SW do you own?
How long have you had it?
What are you using on it and what Ohms/Wattage/ and Batteries are you using?
I usually get this message chain vaping a .1 -/+ build or using Temp control and chain vaping...
Your caps are on btw
What Model SW do you own?
How long have you had it?
What are you using on it and what Ohms/Wattage/ and Batteries are you using?
I usually get this message chain vaping a .1 -/+ build or using Temp control and chain vaping...
Your caps are on btw
Last edited:
Thanks guys for the replies. Now i think its ok.. its just the inside connector is filled with juice. I remove the cover and clean ut with used organic cotton. Now im using it and the error does not occur anymore. Ill check until tommorow..
Dirty connectors will do that as they create resistance and heat when you go to use the mod and the mod sees that heat as the RDA must be overheating or on fire. Make sure to clean that 510 every so often and you wont have many issues with the Snow Wolf...Its a beast.
I use the same RDA, That can be from Over dripping or condensation building up or if you pull the cap off alot. I drip through the tip or pull the tip off and drip into the barrel and it reducing the leaking issue.
I have the Mini version and its even more of an issue so the cap never comes off and I drip until the cotton is wet.
Twisted and Mini Mes
Mini Deck and My New Build Last Night- 2x22K/ .5 Ribbon Fused Clapton:
I use the same RDA, That can be from Over dripping or condensation building up or if you pull the cap off alot. I drip through the tip or pull the tip off and drip into the barrel and it reducing the leaking issue.
I have the Mini version and its even more of an issue so the cap never comes off and I drip until the cotton is wet.
Twisted and Mini Mes
View attachment 38172View attachment 38173
Mini Deck and My New Build Last Night- 2x22K/ .5 Ribbon Fused Clapton:
View attachment 38176View attachment 38177
Very nice work. I've decided a Snow Wolf v1.5 is my next mod but man are they tough to find black.
Ebay my friend, Ebay
still same problem, i already tried other rda and battery...
What Ohms are your build and is the Snow Wolf hot? You never mentioned the Batteries brand/type or Coil resistance, these factors matter very much. Also if you taking long draws and chain vaping this tends to happen when the mod gets hot. If you arent using a low resistance build and your using authentic batteries that are above 20A CD then it is the mod and I would contact Asmodus.
tried batts : samsung inr 18650 25r 2500 mah / lg hg2 18650 30a 3000 mah
tried rda's : velocity/13 heavens/mutation x v4
builds : .3 ohms / .4, .1 ..
nichrome 80 24 g, kanthal wires...
tried rda's : velocity/13 heavens/mutation x v4
builds : .3 ohms / .4, .1 ..
nichrome 80 24 g, kanthal wires...
Yes then I would contact Asmodus and try to get it replaced.