Become a Patron!

Anarchist Wire for Noisey Cricket

SirChalice

SirChalice

Hey Community,

Im trying to figure out how I should build this Anarcist Wire 20 Gauge for a dual coil setup achieving .3 ohms or a bit higher. I have a 3mm bit and a 2.4mm bit. I hope aomeone could help me.

---- I have a bunch of room in the atty. Building for a Goon 24.
 
MEENMAN83

MEENMAN83

Bronze Contributor
Member For 4 Years
Member For 3 Years
I'd go with a higher gauge. 20 gauge nicrome/anarchist wire is too low of ohms to mess with on a noisey cricket.
 
r055co

r055co

VU Donator
Platinum Contributor
Member For 4 Years
SirChalice said:
Hey Community,

Im trying to figure out how I should build this Anarcist Wire 20 Gauge for a dual coil setup achieving .3 ohms or a bit higher. I have a 3mm bit and a 2.4mm bit. I hope aomeone could help me.

---- I have a bunch of room in the atty. Building for a Goon 24.
Click to expand...
Steam Engine is your best friend.

So question, sounds like you are new at building since you are asking a very basic fundamental question. Did you do your homework before diving into Mech's?

Sent from my Nexus 6 using Tapatalk
 
Diescum88

Diescum88

Gold Contributor
Member For 4 Years
Everpresentnewb said:
well, Nichrome20 at a 3mm diameter dual at .3 ohms is a nice 23 wrap coil.... Hope you have a BIG build deck....
Click to expand...
This may sound like a challenge to some but I don't think you could really fit that in a deck to use on the noisy cricket due to the fact of the button placement, restricts you to 24 or 25mm atty at most if I remember correctly

Sent from my SAMSUNG-SM-G930A using Tapatalk
 
r055co

r055co

VU Donator
Platinum Contributor
Member For 4 Years
SirChalice said:
@r055co - I'm not new to building just wanted to know what I should do in this particular instance.
@Diescum88 - My Goon fits well on my noisey cricket. Check my new IG photo. @SirChalice
Click to expand...


You need to use Steam Engine.

Also this -

Everpresentnewb said:
well, Nichrome20 at a 3mm diameter dual at .3 ohms is a nice 23 wrap coil.... Hope you have a BIG build deck....
Click to expand...


Bottom line though is I wouldn't use 20g at all, plus I really don't recommend going lower that 0.4 Ohms.
 
Everpresentnewb

Everpresentnewb

Bronze Contributor
Member For 4 Years
Member For 3 Years
ECF Refugee
well you asked about 20G and wanted it at .3.... I did use steam engine and that was what it spit out. I would look at getting some 26, 24, and 28g... Those are my main gauges and I can build coils to fit most if not all of my needs and resistance ranges.
 
r055co

r055co

VU Donator
Platinum Contributor
Member For 4 Years
Everpresentnewb said:
well you asked about 20G and wanted it at .3.... I did use steam engine and that was what it spit out. I would look at getting some 26, 24, and 28g... Those are my main gauges and I can build coils to fit most if not all of my needs and resistance ranges.
Click to expand...
Personally I like 30(or 32)x2/36 Kanthal Fused Claptons on my =< 24mm RDA's on my series mod's. Then 29(or 30)x2/36 317L Fused Claptons on my 30mm devices, I build a bit hotter with 30mm devices due to the bigger chamber.
 
Everpresentnewb

Everpresentnewb

Bronze Contributor
Member For 4 Years
Member For 3 Years
ECF Refugee
I figured since he was asking about using 20g to build a 3mm .3 dual setup I wouldnt try to confuse him with things like that... Personally i like 28G zippers with a 36G fusing wrap.
 
You must log in or register to reply here.

VU Sponsors

Top