Good news!
Become a Patron!
BC Box Mods
- Thread starter cupracer92
- Start date
Boom told you! LOL
Clean!
Dual 13 wrap 24g at .57ohm
I like to stay around the .3-.2 range with box mods, and I can still use that on a tube mod.
They were shipping the high 600 last week. I think they are only 2 of the 4 who do soldering the others just assembly maybe. Can't be any more weeks LOL!And now they selling a triple battery box...
Oh that's nothing... was looking at a 4 battery box someone makes. And they are 26650 boxes ...
Yes on the way same as yours was will be here tomorrow. Did not leave MI until yesterday and I'm ready! So how has yours been after a week?
It's awesome. I use the build I showed you almost all day in series mode. A smaller build, in parallel, would last a while! The small covering around the switch came off and will rattle around in the box until I glue it back on. But other than that I love it. My wife uses an MVP 2 and thinks my box is huge. It is big. I think I might prefer a Hammond g box size.
Good to know. I usually build dual coils from 0.11-0.7 ,going to rebuild my Airek to around 0.3 to see how that works with both parallel & series. I hope it holds up parts coming off? Saw the 420 guy have his volt meter fall off..Yes the Hammond G is smaller but is the one they use that large? Is it close to the IPV 3 size?
Well I received it today not a bad device.It's not much bigger then the IPV3 about 1/4 in weight and height fits good in the hand.Had to glue the volt meter back ,
super glue did not hold.I have a .28 build on my Dark Horse ,have not tried a lower build yet.I'm happy...
super glue did not hold.I have a .28 build on my Dark Horse ,have not tried a lower build yet.I'm happy...
You mean it shows when you push the button right not always on?
I don't have a switch on the meter only the parallel-series one.
I have seen some with that but nope I don't.
I messaged the owner to see if they had any used pre-builts laying around the shop, unfortunately they didn't and they said they don't do rush orders.
Luckily he did inform me the wait time at the moment is about 7 days. How is the voltage drop? Im worried about drop because of the LEDs and DFPT switch. I spent the last of my vape budget for a year maybe more on this box so I need some reassurance in my decision. How is your's?
Luckily he did inform me the wait time at the moment is about 7 days. How is the voltage drop? Im worried about drop because of the LEDs and DFPT switch. I spent the last of my vape budget for a year maybe more on this box so I need some reassurance in my decision. How is your's?
Don't worry about voltage drop with this box,I don't have the halo but LEDs don't use much power.These boxes are made to order and it's a small shop,all depends on how many they have in front of you.Just follow the guides on how low to build for series v parallel .I build higher now no need to build crazy low anymore.
Then use it in parallel only,believe me you don't need to try that in series. They tell you to start around .5 and see if you can handle that first in series. Like I said start building higher,that's 7+ volts your talking about.Have a .35 build on a Dark Horse and try a few rips in series..a 2-3 sec ones...Do get some good batteries just for this mod that have not been used before,and only use them for it.
Hey Tim how do you like the mod?
TimB gives good advice. .28 @ 8.4v (series) is pushing 30amps at 252watts. In parallel mode that same build is 15amps @ 63watts
Use Steam Engine calculator It will take the guess work out of the equation (what am i doing up this late)
I looked at the picture you posted the switch looks simple it just bridges the contacts. Is everything making contact when in the series position ? That sucks I would contact them and send it back it's not your fault.Lifetime warranty right use it! And if something is loose you don't want a short in the box..The battery sled contacts are not that heavy I added a little rubber under them to give it more spring. The switch and the sled are the weakest parts of the whole box..