Choosing The Right Atomizer/Coil Heads

[Adenrele1982]

Good Day To The Vaping Community!

I seek you input, once again, as I take additional steps towards fully embracing vaping! I'll be using the RX200 with Uwell Crown or Gemini Vaporesso Sub Ohm Tank. I am now looking to determine which atomizers/coils to purchase. I will stay away from nickel at this point, being a novice. So, Stainless Steel and Kanthol are my options. I will be purchasing both Kanthol and Stainless Steel Atomizers/Coils. I will be experimenting with both in Wattage Control and Temp Control options.

I've noticed the Vaporesso SS Ccell atomizers/coils vary in ohms, from .05 ohms to .08 ohms(Vaporesso CCells). Kanthol(.09 ohms)

Am I correct in my understanding that SS .05 & Kanthol(.09) is for lower watts(20-40watts) and SS .08 is for higher watts(40-75)?

If this is the case, would I not want to vape at any higher watts with either?

If so, which coils would be used in higher wattage?

What is the difference between the Kanthol .09 and SS .08? Is the taste and/or vapor production different? How so? Is one better than the other?

Also how do the above factor in Temperature Control levels?

I noticed that the Uwell SS Atomizers/coil heads come in .25 ohms, .05 ohms, and 1.2 ohms?

What are the differences? Are any of these Kanthol, as I can't tell from the site I am looking at. How should these be used?

I'll likely be purchasing a pack of each to determine what I like best, but before I do, I'd like to gain insight into how they would be used and why?

This forum has been supremely pivotal in my vaping education thus far. I have no doubt that further insight and direction will be gained, which will allow me to make a most informed decision and get the most out of my vaping experience, while being safe.

Hope to hear from you, soon!

#VAPORNATION

 

[AmandaD]

The Crown coils are all stainless steel - at least I'm sure the 0.25 and 0.5 ones are. They both work best at at least 60 watts, although you can use the 0.5 around 50 watts. The 1.2 ohm coils are my least favorite, and those run max of 40 watts - but to me the flavor is lacking. I use themall in regular wattage mode, not TC mode, although some do use them in SS TC mode with success.

 

[Adenrele1982]

The Crown coils are all stainless steel - at least I'm sure the 0.25 and 0.5 ones are. They both work best at at least 60 watts, although you can use the 0.5 around 50 watts. The 1.2 ohm coils are my least favorite, and those run max of 40 watts - but to me the flavor is lacking. I use themall in regular wattage mode, not TC mode, although some do use them in SS TC mode with success.

Peace AmandaD, Thank you, very much! Do you think it possible that the 1.2 ohm coils are better suited for TC? & maybe, that is why the flavor isn't as good? Either way, I appreciate you taking time and energy to share insight.

 

[AmandaD]

No - they are just overall pretty sad in the flavor department. Even the subtank coils give better flavor than those LOL

I love my crowns - I generally stick to the 0.25 ohm coils in wattage mode - but, as I say, they do need at least 60 watts to shine!

 

[Adenrele1982]

No - they are just overall pretty sad in the flavor department. Even the subtank coils give better flavor than those LOL

I love my crowns - I generally stick to the 0.25 ohm coils in wattage mode - but, as I say, they do need at least 60 watts to shine!

LMAO! Thanks.

 

[Miranda]

I have eleaf istick 60 watt, been vapeing kanthal went to switch to ni and not sure what to set it on the mod I know it needs ni mode but what other settings to vape safely? It is pre built ni coil that came with melo 2 tank