I have a Tesla Two mod and a Smok micro tfv4 tank. It was getting a burning taste after not even a week of vaping, so i figured time to change the coil. I bought a pack of coils, changed it and now the tank is not producing a lot of smoke like it was in the beginning. The flavor has gone down as well as the amount of smoke i can pull from the mod. Any help/advice would be great! I just bought the tank before it went to shit within a week! It also has a nasty taste when i go to vape, nothing like a burning taste, just out right gross
Become a Patron!
Help!
- Thread starter blakeenathaniel
- Start date
JuicyLucy
My name is Lucy and I am a squonkaholic
VU Donator
Diamond Contributor
ECF Refugee
VU Challenge Team
Member For 5 Years
Welcome to VU!
Are the coils you bought for replacement the same ohms as the original that tasted burned?
Technically, your mod and atty do no produce smoke at all, it produces vapor.
What brand/type of batteries are you using? Are they a dedicated married pair?
Are the coils you bought for replacement the same ohms as the original that tasted burned?
Technically, your mod and atty do no produce smoke at all, it produces vapor.
What brand/type of batteries are you using? Are they a dedicated married pair?
The coils are the exact same as the original. The battery is built into the mod, therefore it is one that you plug into an adapter to the wall and it charges that way.
The coils i am using are the Micro CLP2, clapton dual core coils. .3 ohms with 30w-60w
well
firts off
all the coils are mass produced
so sometimes you get a bad one
coils do need broken in which is alittle hard to do on your mod
so that may be the issue
there could be dirt between the coil to base connection or in the 510 connector
if the 510 on your mod is adjustable which i bet it is, there cold be dirt in it
the coil may not be screwe dall the way into the base
all those things could be your issue
your mod is like a unregulated mechanical box mod
so when th ebattery drains down- the hit is weaker
make sure you are fully charged
new coils often taste very nasty if not primed or broken in well
and osmetimes coils just take like shit and need trashed from day 1
firts off
all the coils are mass produced
so sometimes you get a bad one
coils do need broken in which is alittle hard to do on your mod
so that may be the issue
there could be dirt between the coil to base connection or in the 510 connector
if the 510 on your mod is adjustable which i bet it is, there cold be dirt in it
the coil may not be screwe dall the way into the base
all those things could be your issue
your mod is like a unregulated mechanical box mod
so when th ebattery drains down- the hit is weaker
make sure you are fully charged
new coils often taste very nasty if not primed or broken in well
and osmetimes coils just take like shit and need trashed from day 1
Yes i do prime them before vaping, even let it sit 10 minutes before actually vaping on it.
How do you propose i properly clean out the 510? I'll check all of these things and HOPEFULLY one of them is the issue. I'll try swapping the coil now as well.
well normally i usea q tip
but every once in a blu emoo there is dirt under that flat piece that has a spring under it
and thats a pita
a needle or pin is needed tehn
part fo your issue is a mod you cant regulate
many pople recommend when you start a new coil you hit it much lower watts then what you would normally
and slowly over the course of many drags bring the wattage up
WHY
cuz SOMETIMES if the cotton aint all the way really really saoked
especially near the coil
you wind up burning a small bit of cotton and can never get rid of that flavor
but every once in a blu emoo there is dirt under that flat piece that has a spring under it
and thats a pita
a needle or pin is needed tehn
part fo your issue is a mod you cant regulate
many pople recommend when you start a new coil you hit it much lower watts then what you would normally
and slowly over the course of many drags bring the wattage up
WHY
cuz SOMETIMES if the cotton aint all the way really really saoked
especially near the coil
you wind up burning a small bit of cotton and can never get rid of that flavor
Gotcha! Thanks for this info you have been great in helping
I will try cleaning all my equipment as good as possibly can be and hopefully this solves all the issues! Thank you for your help and advice. you have been of great help!
JuicyLucy
My name is Lucy and I am a squonkaholic
VU Donator
Diamond Contributor
ECF Refugee
VU Challenge Team
Member For 5 Years
Hopefully it solves your issue, let us know!
Last edited:
Cleaned it all out, let it dry and primed my new coil. It's now spitting the juice up and out of the mouth piece, any thoughts?
JuicyLucy
My name is Lucy and I am a squonkaholic
VU Donator
Diamond Contributor
ECF Refugee
VU Challenge Team
Member For 5 Years
That really sounds like it is getting way too hot for the atty/coil combo
The Tesla II is a really great mod, but it's not a great beginners device at all.
Are you maybe hitting the button a little longer than it needs?
I'm vaping mine right now at about 1 ohm on a Sapor. On this mod, I don't hit the power until I have it in my mouth and ready to inhale, then it only needs like one second of power to provide a nice long DL hit.
To MTL it only takes a fraction of a second.
The Tesla II is a really great mod, but it's not a great beginners device at all.
Are you maybe hitting the button a little longer than it needs?
I'm vaping mine right now at about 1 ohm on a Sapor. On this mod, I don't hit the power until I have it in my mouth and ready to inhale, then it only needs like one second of power to provide a nice long DL hit.
To MTL it only takes a fraction of a second.
Change o- rings there could be a vacuum loss ......
Sent from my 710C using Tapatalk
Sent from my 710C using Tapatalk
PreparationHero
I drink and I know things
VU Donator
Bronze Contributor
Member For 3 Years
Member For 2 Years
Member For 1 Year
ECF Refugee
I don't have this tank so I'm not going to pretend to be an expert. But you might have a little flooding. Grab a paper towel and wrap it around the air flow, hold the mod upside down fire the mod and BLOW into it for a few seconds to get the excess juice out. Then it should work fine.