Psyclonemods Entheon/Hadeon

[SoiDog]

Fairly new to this and my first rda was Dead Rabbit , and when i first tried it i understood what my friends were talking about...that tasty experience.

Just shy of 4 moths of vaping i ordered an Entheon/Hadeon , and this one is off the chart.
What coils are you folks using on it and why?

Sent fra min SM-G930F via Tapatalk

 

[MrMeowgi]

Usually just a fused Clapton. I had both caps thought. The hadeon cap had more air to me so I could run a larger coil.

Sent from my LM-Q610(FGN) using Tapatalk

 

[KingPin!]

Saving for this atty, I’d probably run it the same way Wtmke does

 

[SoiDog]

Will change from alien and see how it preforms. Maby i have One wrap too mutch?
Got staple staggered and regular claptons , so i Will fiddle around With it to see what suits Me best.

 

[scalewiz]

I run a simple parallel wind 26 ga. in a BF squonk setup. Fast heatup time, and able to produce more with a lower wattage. Great atty! Easy to build with any wire due to the reversible/rotatable wire clamps and it has a good sized juice well. I got a couple clear caps from Fasttech and it makes it real easy to see my wick and my squonk. I'm DTL, so I keep the airflow wide open.

At the moment though I'm running the Mulciber with a fused clapton. This is really a squonk atty as the juice well is VERY shallow, but it too has excellent performance. Truthfully I think the Entheon is a better all-round atty, and it beckons me from my desk.

 

[SoiDog]

Can you guys post pictures of coil placement...hight?

Sent fra min SM-G930F via Tapatalk

 

[MrMeowgi]

My coil is nasty as ever right now so no pic but I level the top of the coil with the screws. Where the airflow hits the bottom of the coil the pull air up through it

Sent from my LM-Q610(FGN) using Tapatalk

 

[SoiDog]

My coil is nasty as ever right now so no pic but I level the top of the coil with the screws. Where the airflow hits the bottom of the coil the pull air up through it

Sent from my LM-Q610(FGN) using Tapatalk

Gotcha...will adjust mine abit to see.

 

[SoiDog]

Been trying for days to find something to get flavor , but it did not really pop.
Most of times it was sweet vapour , with little to none flavor.

Whent trough my coils after seeing a review , and found some small fused claptons.
N80 26ga*2+38ga ø3 5.5wrap (Geek Vape)

There was more flavor but not impressive , so i started to lift the coil a notch and revicked....Boom!
Been 1 week since i got this rda , and tbh i was thinking to get rid of it coz i had trouble finding coil and coil placement.

Now that i have found a fix for it , i started to look around for some more expencive handmade coils.


Sent fra min SM-G930F via Tapatalk

 

[MrMeowgi]

Been trying for days to find something to get flavor , but it did not really pop.
Most of times it was sweet vapour , with little to none flavor.

Whent trough my coils after seeing a review , and found some small fused claptons.
N80 26ga*2+38ga ø3 5.5wrap (Geek Vape)

There was more flavor but not impressive , so i started to lift the coil a notch and revicked....Boom!
Been 1 week since i got this rda , and tbh i was thinking to get rid of it coz i had trouble finding coil and coil placement.

Now that i have found a fix for it , i started to look around for some more expencive handmade coils.


Sent fra min SM-G930F via Tapatalk

Careful not to ohm to low. It will get hot in the lower 2's

Sent from my LM-Q610(FGN) using Tapatalk

 

[SoiDog]

0.32 ohm and low wattage atm

Sent fra min SM-G930F via Tapatalk