Become a Patron!
Rx200 3.1 update
- Thread starter Gheed
- Start date
Notice any different except increase to 250 watts?
Sent from my iPad using Tapatalk
Sent from my iPad using Tapatalk
Vapin_4_Real
VU Donator
Bronze Contributor
Member For 3 Years
Member For 2 Years
Member For 1 Year
ECF Refugee
This update is just plain pathetic. Exactly how does Jaybo expect for 250 watts to come out of this mod other than turning it up on the screen with no atty attached? Bravo Wismec Bravo 
Vapin_4_Real
VU Donator
Bronze Contributor
Member For 3 Years
Member For 2 Years
Member For 1 Year
ECF Refugee
I did update mine tho. Not sure even why...
This update is just plain pathetic. Exactly how does Jaybo expect for 250 watts to come out of this mod other than turning it up on the screen with no atty attached? Bravo Wismec Bravo
Dear WISMEC Customers:
Wismec just released the upgraded firmware V3.10 for Reuleaux RX200.
In this version, the maximum output power is upgraded to 250W. One thing should be noted that the recommended resistance range for 250W is 0.1-0.32ohm while the recommended resistance range for 220W is 0.1-0.37ohm.
WISMEC Marketing Team
Wismec just released the upgraded firmware V3.10 for Reuleaux RX200.
In this version, the maximum output power is upgraded to 250W. One thing should be noted that the recommended resistance range for 250W is 0.1-0.32ohm while the recommended resistance range for 220W is 0.1-0.37ohm.
WISMEC Marketing Team
Vapin_4_Real
VU Donator
Bronze Contributor
Member For 3 Years
Member For 2 Years
Member For 1 Year
ECF Refugee
on 9 volts? lol yea ok
I have this and a Cuboid, and one thing I really like about the Cuboid is that it has a governor built in. I had never noticed it until I was reading and saw a post about it not going any higher than x=25A, so I tested it out, and sure as shit.
Now it looks like this gonna happen too...
http://www.eciggity.com/reuleaux-rx200-front-back-cover-by-wismec/
http://www.eciggity.com/reuleaux-rx200-front-back-cover-by-wismec/
Damn it! I just ordered from them a couple of days ago for an Augvape Boreas and they didn't have them then when I ordered.
LmaoOk, so let's get this straight. 250watts, 9volts, and no added safety features?I'm in!
"Here hold my beer."
They would have to put out a whole new mod with a much bigger screen to accomplish that. I like the Evic set up more than most but prefer the RX to the latter.... I just did the update on mine, despite starting a thread just a couple of weeks ago where I bitched about the 300w Kooper, I couldn't resist.
@Ben-Rod , thanks for the heads up on the interchangeable plates.
I love the upgrade. I've put all my big series builds on it and it works great. Can't wait to get home and spin up those big builds that were just to low to put on any of my other boxes. Think I'll start with a 3x24 alien.
This has really upped my anticipation of the VC600 latter this year.
This has really upped my anticipation of the VC600 latter this year.
I too would like to see an amp pull number on the screen.
But, they say 0.1 to 0.32 is the recommended ohm range to push 250 watts out of it. Even at 0.32ohm youd be damn near pushing 30 amps through the battery to hit 250watts, which even with a good VTC4 is pushing it, nevermind going any lower than that. You can still over push your batteries in a regulated mod, them shits can still vent and pop.
But, they say 0.1 to 0.32 is the recommended ohm range to push 250 watts out of it. Even at 0.32ohm youd be damn near pushing 30 amps through the battery to hit 250watts, which even with a good VTC4 is pushing it, nevermind going any lower than that. You can still over push your batteries in a regulated mod, them shits can still vent and pop.
Vapin_4_Real
VU Donator
Bronze Contributor
Member For 3 Years
Member For 2 Years
Member For 1 Year
ECF Refugee
Skyrim fonts 
Now I need to get an RX ... just for the cool fonts!Skyrim fonts
Vapin_4_Real
VU Donator
Bronze Contributor
Member For 3 Years
Member For 2 Years
Member For 1 Year
ECF Refugee
There was about 8 or so diff fonts I found. Pretty cool I guess.
Dont think the fonts are included in the update. Thats just from people editing the properties of the software or whatever. There was a guy here a while ago explaining how to do it.
And as far I know the minimum resistance hasnt changed from the 0.1 it was prior, and it probably wont. There arent many mods out there that can fire below .1.
And as far I know the minimum resistance hasnt changed from the 0.1 it was prior, and it probably wont. There arent many mods out there that can fire below .1.
Snow wolf and Hohm Wrecker can
Yea, but do they still sell the Hohm Wrecker? I looked last night breifly and couldnt find them new and in stock.
You got one? Does it really do well with kanthal temp mode?
I posted a thread because I didnt see this one but yeah I am LOVIN the update!!!
Good thing yours didn't brick like a number of other ones I heard about. Joyetech/Wismec must really have some lousy programmers. SS TC still isn't fixed.
So you still have to use tcr a bit higher for it then?
Sent from my LGMS345 using Tapatalk
Sent from my LGMS345 using Tapatalk
No it works with SS TC for a few weeks and then suddenly it quits working and just displays temp protect instantly when you hit the fire button. Happened to both of mine.
Oh you mean in ss mode? I only use tcr mode it seems to be most effective with this mod
Sent from my LGMS345 using Tapatalk
Sent from my LGMS345 using Tapatalk
So the update applies to both the RX & DNA but are the problems the same? Such as SS in TC mode not working and the devices going to shit when you try and update?
I don't think it applies to both the RX and DNA. They are completely different chips, and require completely different coding to program. I believe the concern is specifically with the RX based chips.
That's what I was thinking, thanks Dev!
Sent from my SM-G925P using Tapatalk
Sent from my SM-G925P using Tapatalk
No the DNA is totally different and doesn't suffer from all of the issues that the RX200 board has. Joyetech/Wismec can't even bother with a design that can read battery voltages correctly. No wonder there is a high failure rate. As it sometimes reports good batteries are bad and bad batteries are good. It is just a total mess IMHO and many things should have been corrected before it hit the market. But I guess Joyetech/Wismec doesn't care about being shabby, just pump out more cheap crap out the door.
Nor have I heard one single case of Joyetech/Wismec ever honoring one single customer's warranty claim. I read online of one vendor (wish I would remember) who sent back defective units back to Joyetech/Wismec for repair and never got them back or ever heard from them again. So the vendor stated they themselves still support their customers and will replace any defective Joyetech/Wismec device out of their own pockets.