Become a Patron!
Rx200s below 0.1 ohms
- Thread starter Smowgli
- Start date
Built with what.
Temp control is what you seek, unless it is a small inner diameter not seeing how this is possible.
And there's nothing wrong with that. If your rda is a two post or some other variation that will accept a single coil you're good to goWell... you can use half of it.
So I did a single 24 g reads out.2 ohms. Has a nice vape to it. I was wondering I tend to how thinner the wire the lower the watts. I'm not reading as much about this all because I rather experience things while doing them, and of course ask for help here. Hope you guys don't mind
Kind regards Kenneth.
Kind regards Kenneth.
First thing... before you tighten down the post screws, keep the mandrel/rod/screwdriver you rolled the coil on inserted and gently bend/shift the coil toward the center position.
Each should be nearly centered and squared up.
Height is up to you... it depends on the design of the atomizer and where the airflow is coming from, how it hits the coil. Play with the possibilities.
To get neater lightly spaced coils... just after rolling (roll an extra wrap or two), gently tug and using your nails separate each wrap and lightly stretch the coil out evenly. Then compress it back together. Have to press a few times. Then using pliers pull a bit of the coil out from each end while angling into the coil compressing it. Flip the coil around so you have the handle of the driver to press against. This will remove those extra wraps.
Do it right and they'll be evenly spaced.
For touching or "contact" coils... you should wrap them tightly to begin with. Pulsing and glowing while squeezing with tweezers will get it to heat evenly (watch the YouTubes) but it won't easily eliminate spacing (for me at least).
When you have the coils mounted properly... wicking an RDA is usually straightforward and fairly easy. Some RDAs have their own preferences though. A little can be enough... some like a bed of wicking. Or anything in-between. Easy enough to redo and experiment.
Yeah sorry... I got on a roll there and just started throwing in more things.
Post kinda got away from me.
But it's all good basic info, and of course nothing is set in stone... so when you find a better way, use it.
The coil calculator at Steam-Engine is one of the better ones (all of them actually).
You can get a quick familiarity with the resistance changes when you alter any number of aspects of your coil.
http://www.steam-engine.org/
Post kinda got away from me.
But it's all good basic info, and of course nothing is set in stone... so when you find a better way, use it.
The coil calculator at Steam-Engine is one of the better ones (all of them actually).
You can get a quick familiarity with the resistance changes when you alter any number of aspects of your coil.
http://www.steam-engine.org/
hmmm i still don't understand Jim i did the following:
kanthal A1 APM (dunno what APN means)
round
24 gauge awg (merican wire, i'm from europe so dunno if that is correct)
0.511mm (by default when choosing 24 gauge)
dual coil setup
1ohm target res.
diameter 3mm
leg lenght 5mm by default
and the result states that i have to do 21.94 wraps ?!? i dunno bout your deck but mine isn't suited for that lol
kanthal A1 APM (dunno what APN means)
round
24 gauge awg (merican wire, i'm from europe so dunno if that is correct)
0.511mm (by default when choosing 24 gauge)
dual coil setup
1ohm target res.
diameter 3mm
leg lenght 5mm by default
and the result states that i have to do 21.94 wraps ?!? i dunno bout your deck but mine isn't suited for that lol
I'm not sure that you're inputting the correct parameters....hmmm i still don't understand Jim i did the following:
kanthal A1 APM (dunno what APN means)
round
24 gauge awg (merican wire, i'm from europe so dunno if that is correct)
0.511mm (by default when choosing 24 gauge)
dual coil setup
1ohm target res.
diameter 3mm
leg lenght 5mm by default
and the result states that i have to do 21.94 wraps ?!? i dunno bout your deck but mine isn't suited for that lol
kanthal A1 APM (dunno what APN means)
round
24 gauge awg (merican wire, i'm from europe so dunno if that is correct)
0.511mm (by default when choosing 24 gauge)
dual coil setup
1ohm target res.
diameter 3mm
leg lenght 5mm by default
Will give you :
If you ACTUALLY mean .1 ohm, then.....
You're talking less than 2 wraps per coil.... I gotta ask, what's the attraction to get to the minimum your mod will fire at? It would be easier(more wraps) to go with SS316L, and you can still use power/wattage mode.