Become a Patron!

Squonkers are Bonkers

SteelDriver

Gold Contributor
Member For 4 Years
Been looking myself just to try something new. I'm liking the bezerker.
Hey there fellow Bonkers -

How is your Saturday going?

Any thoughts on the following newer, authentic MTL RSAs?
  • Vapefly Galaxies
  • GeekVape Ammit
  • Vandy Vape Beserker

I'm trying to find one in the middle-ground, with a range between restricted DTL and more open MTL...

The reason that these have caught my attention is that with a SMALLER hole closer to the coil where the air hits the coil, this creates a higher-velocity air flow, which in my experience creates more flavor, and more heat-feeling to your mouth, without needing high power...

My main use will be on the v1 of the Pico Squeeze for now.

Please tell me your thoughts - good, bad and ugly regarding these atomizers listed above. :)

Sent from my LG-D850 using Tapatalk
 

BrewBear

Platinum Contributor
Member For 4 Years
I must've missed the Ammit....or just ignored it.
I would say of the other two, the Galaxies is a bit better flavor and more flexible.
My main dislike with the berserker was the awkward way the coil mounts, the need for very long wick tails, the overall chamber size (too big IMHO ) you get a hollow vape....well, at least I did.
 

Papachaz

Silver Contributor
Member For 2 Years
I must've missed the Ammit....or just ignored it.
I would say of the other two, the Galaxies is a bit better flavor and more flexible.
My main dislike with the berserker was the awkward way the coil mounts, the need for very long wick tails, the overall chamber size (too big IMHO ) you get a hollow vape....well, at least I did.

I agree with bear on the berserker. It’s just not quite there. I tried multiple coils and coil placement and it never really popped.


Carpe Nidor
 

~Don~

Platinum Contributor
Member For 5 Years
I fucking need to stop spending on vape gear.

Ok carry on lol


to be relevant

65e3c8c4033b05ae4a1de1e7f99f34af.jpg
 

snake94115

Diamond Contributor
Member For 4 Years
Hey there fellow Bonkers -

How is your Saturday going?

Any thoughts on the following newer, authentic MTL RSAs?
  • Vapefly Galaxies
  • GeekVape Ammit
  • Vandy Vape Beserker

I'm trying to find one in the middle-ground, with a range between restricted DTL and more open MTL...

The reason that these have caught my attention is that with a SMALLER hole closer to the coil where the air hits the coil, this creates a higher-velocity air flow, which in my experience creates more flavor, and more heat-feeling to your mouth, without needing high power...

My main use will be on the v1 of the Pico Squeeze for now.

Please tell me your thoughts - good, bad and ugly regarding these atomizers listed above. :)
Watch Todd get confused.

 

snake94115

Diamond Contributor
Member For 4 Years
Darned White squeeze's are getting expensive. Over $19 now from FT.
White is the most expensive one... More exclusive?

But worth it :)
What was that old Chuck Norris movie?
Good Guys Vape White?
Nope it was (Good Guys Wear Black)
I'll just go back to vaping my black Wraith & black Wasp With a black drip-tip while squonking blackberry Jam Monster
 

Train

Gold Contributor
Member For 5 Years
Advice?

I do NOT do much in the way of working on mods - funny, since I run like 30 mech squonkers...but it's true.
Still, I have one that I want to "gut" - and just use the box replacing the contact strips and 510.

Any source that's good for both? Most stuff is always out of stock on Moddog, but I figured Moddog or Modmaker for the 510.

This is kind of how it's set up - I'll want to get a 510 that's "flush" even if I have to drill the delrin. And I'll want to go silver probably.
Might leave the "spring" approach for battery variance - that or just shim up the contact point...

upload_2018-8-21_20-46-3.png
 

DogMan

VU Donator
Diamond Contributor
Member For 5 Years
Advice?

I do NOT do much in the way of working on mods - funny, since I run like 30 mech squonkers...but it's true.
Still, I have one that I want to "gut" - and just use the box replacing the contact strips and 510.

Any source that's good for both? Most stuff is always out of stock on Moddog, but I figured Moddog or Modmaker for the 510.

This is kind of how it's set up - I'll want to get a 510 that's "flush" even if I have to drill the delrin. And I'll want to go silver probably.
Might leave the "spring" approach for battery variance - that or just shim up the contact point...

View attachment 118221
Go the silvered out modmaker 510

Strips can be copper for springiness. Then solder on a .999 silver pad to make the contact point with 510 nut
 

Zaxxaz

Silver Contributor
Member For 4 Years
Advice?

I do NOT do much in the way of working on mods - funny, since I run like 30 mech squonkers...but it's true.
Still, I have one that I want to "gut" - and just use the box replacing the contact strips and 510.

Any source that's good for both? Most stuff is always out of stock on Moddog, but I figured Moddog or Modmaker for the 510.

This is kind of how it's set up - I'll want to get a 510 that's "flush" even if I have to drill the delrin. And I'll want to go silver probably.
Might leave the "spring" approach for battery variance - that or just shim up the contact point...

View attachment 118221

You can get contact strips and the 510 from mod maker. I know they carry cooper strips,but I think they have silver plated also. And you can get the silver kit for the 510.


Sent from my iPhone using Tapatalk
 

Train

Gold Contributor
Member For 5 Years
Cool - I think have all the bits in a cart. Just hesitating before pulling the trigger, since shipping basically doubles the cost :(.
I'll do it, just need to find a little money first, to feel better about spending anything.

Go the silvered out modmaker 510

Strips can be copper for springiness. Then solder on a .999 silver pad to make the contact point with 510 nut
You can get contact strips and the 510 from mod maker. I know they carry cooper strips,but I think they have silver plated also. And you can get the silver kit for the 510.


Sent from my iPhone using Tapatalk
 

Zaxxaz

Silver Contributor
Member For 4 Years
Cool - I think have all the bits in a cart. Just hesitating before pulling the trigger, since shipping basically doubles the cost :(.
I'll do it, just need to find a little money first, to feel better about spending anything.

You could check brosciencevapes also. They are in the US and carry the mod maker 510s and bottles. Don’t know if the have added the contact strips or if they plan to. I’d give you a link but I’m on my phone.


Sent from my iPhone using Tapatalk
 

Arthur-VU

Silver Contributor
Member For 2 Years
An update on my issues with the Inbox v3...

I let it set for 5 days. Not that it would do anything, but maybe there were capacitors inside that needed to fully drain, and thus allow a full reset of the device.

During that time I discovered that there was a newer version of Escribe than what I had installed, so I grabbed that, and installed it over the previous version (Win7 in VirtualBox, since I am on Linux and refuse to install Mono on Linux for the Linux version of Escribe)...

The new version the interface is slightly different (in 'Advanced mode' or 'Manufacturer mode') but otherwise pretty much the same.

I did a factory reset of the Inbox via Escribe. Setup my profiles and materials, left alone all the settings for cutoff voltage and amp drain settings. The default cel cutoff for 18650 was already set at 2.75v.

I then put in one of the older LG HG2 cells, and tried 4 different atomizers on it, all with different resistance coils, 2x SS316L and 2x Kanthal. Vaping on it maybe 40 mins now.

Lo and behold, I'm not getting the flashing battery icon any more, all the way up to 30w.

If it stays like this, I will consider it solved and the issue due to a glitch in the firmware that was cured either by the new version of Escribe pushing the settings differently/better, or that something inside the Inbox where the firmware was saved got corrupted, either some flash storage or an EEPROM chip...

If the issue arises again, I will definitely open a support ticket with Evolv, but for now, fingers crossed.

Thanks ever so much to everyone that offered help, advice and suggestions. I truly appreciate the support, and wanted to say that I think we have a great group of folks here in this thread.

I am very happy right now :stars2:
 

jasonandsarah

Gold Contributor
Member For 3 Years
I really enjoy the Hadaly...I think its one of the only RSAs I wouldn't sell... Cheap as they are second hand...nope. Not the greatest Vape, but a damn good one all the time...til you over squonky then you're like, NOW I REMEMBER WHY I HATE YOU! lol
Wow this is old but did you sell the venna?

Sent from my SM-G955U using Tapatalk
 

MrMeowgi

The Vapin' Drummer
VU Donator
Diamond Contributor
Member For 4 Years
Advice?

I do NOT do much in the way of working on mods - funny, since I run like 30 mech squonkers...but it's true.
Still, I have one that I want to "gut" - and just use the box replacing the contact strips and 510.

Any source that's good for both? Most stuff is always out of stock on Moddog, but I figured Moddog or Modmaker for the 510.

This is kind of how it's set up - I'll want to get a 510 that's "flush" even if I have to drill the delrin. And I'll want to go silver probably.
Might leave the "spring" approach for battery variance - that or just shim up the contact point...

View attachment 118221
Broscience.com

Sent from my Nexus 6P using Tapatalk
 

bx10r

Platinum Contributor
Member For 4 Years
Not sure of the mods but the rdas are apocalypse

Sent from my Nexus 6P using Tapatalk
The red looks rapture rda...the others i can tell...thats a beast rda imo...i have a ss and blue...like the apoc i have coming

Sent from a very cloudy room
 

MrMeowgi

The Vapin' Drummer
VU Donator
Diamond Contributor
Member For 4 Years
The red looks rapture rda...the others i can tell...thats a beast rda imo...i have a ss and blue...like the apoc i have coming

Sent from a very cloudy room
Same angle. Mine is a clone though. No white paint
bb7c8c2fe7bb1c45fc31f68de464b748.jpg
b79119136492881adba52297927894ab.jpg


Sent from my Nexus 6P using Tapatalk
 

MrMeowgi

The Vapin' Drummer
VU Donator
Diamond Contributor
Member For 4 Years
My rapture.. and the tube on top of the red one is the logo on it.. never saw a red one. That and ared apocalypse..omg
cbf59345f9859dee97448043497b2cf5.jpg


Sent from a very cloudy room
Love that skin on yours. Awesome

Sent from my Nexus 6P using Tapatalk
 

DogMan

VU Donator
Diamond Contributor
Member For 5 Years
I couldn't "Like" this one, I think you got the BAM faster than this. You might still get it by Christmas:confused:, tho I really hope it will be faster than that.
I was aware I'd be waiting passed eta. It's OK, but I would like to get it soon
 

Train

Gold Contributor
Member For 5 Years
Speaking of...just built a catfished Maker.
Old school-ish, came out just right: dual Ni80, 28g, for 0.4 ohms.
Perfect! And a new squishy bottle for the Woodvil.
Maker is an oddball RDA - Air from the top is chanelled halfway down the chamber, aimed at outer edge of coils - I like it.

WoodwithMaker.jpg
 
Last edited:

DogMan

VU Donator
Diamond Contributor
Member For 5 Years
Speaking of...just built a catfished Maker.
Old school-ish, came out just right: dual Ni80, 28g, for 0.4 ohms.
Perfect! And a new squishy bottle for the Woodvil.
Make is an oddball RDA - Air from the top is chanelled halfway down the chamber, aimed at outer edge of coils - I like it.

View attachment 118307

new wood something from REO is apparently 75% way to being released

dunno anything else, eric just dropped a hint
 

VU Sponsors

Top