Hi I'll get my Plume Veil with my MVP 20W in some days and I'll do my first coil. So my questions are: minimum ohms I need on my atomizer (the plume) for it to work. And if I do a coil and it's below the correct ohms how do I increase it?
Become a Patron!
Using Plume Veil with iTaste MVP 20W? Minimum ohms?
- Thread starter Corona
- Start date
Pauly Walnuts
Gold Contributor
Member For 4 Years
Member For 3 Years
Member For 2 Years
Member For 1 Year
Member For 5 Years
The mpv 20w wont fire below 1ohm and it has a maximum output of 6amps. If set up properly it will work ok, but to me 6amps is not sufficient power for an rda. Others may or may not agree..
So, any coil or combination of coils higher than 1ohm will allow the device to fire.
Once youve wrapped a coil, you can only decrease the ohms by taking off one wrap at a time. To increase ohms, you need more wraps on your coil, or a larger diameter.
The kanthal gauge you use, the diameter of your coil, and the number of wraps will determine how many ohms your coil is.
This site is your friend,http://www.steam-engine.org/ you need to know how ohms and volts and watts and amps work.
So, any coil or combination of coils higher than 1ohm will allow the device to fire.
Once youve wrapped a coil, you can only decrease the ohms by taking off one wrap at a time. To increase ohms, you need more wraps on your coil, or a larger diameter.
The kanthal gauge you use, the diameter of your coil, and the number of wraps will determine how many ohms your coil is.
This site is your friend,http://www.steam-engine.org/ you need to know how ohms and volts and watts and amps work.
Pauly Walnuts
Gold Contributor
Member For 4 Years
Member For 3 Years
Member For 2 Years
Member For 1 Year
Member For 5 Years
Its really gonna depend on your coil set up. I say that because 20watts is really weak for most rda's to show their true colors. Typically these devices are used for tanks with small chambers and tight draws, like a nautilus or a protank or a kayfun. The plume does have decent airflow control and a way to shrink the chamber size, which is a plus for running at lower wattages.
I used a plume veil for months, using .2-.3ohm builds on mechanicals typically drawing between 15 and 20 amps. This was my sweet spot, but we are all different
You may like it just fine and it may work very well for you. Youll just have to find out and see.
I used a plume veil for months, using .2-.3ohm builds on mechanicals typically drawing between 15 and 20 amps. This was my sweet spot, but we are all different
You may like it just fine and it may work very well for you. Youll just have to find out and see.
Ok guys I changed my mind, cancelled the MVP 20W and got a Smok xPro M50 65W. That would work much better with the Plume veil right?
Another question even that it can subohm, I can still use it with tanks like kanger aerotank and etc right?
Another question even that it can subohm, I can still use it with tanks like kanger aerotank and etc right?
Pauly Walnuts
Gold Contributor
Member For 4 Years
Member For 3 Years
Member For 2 Years
Member For 1 Year
Member For 5 Years
YES!!! This will be much better. 65watts is a huge upgrade and not being chained to +1ohm attys will help your sanity.
You should be able to use it on anything with a 510 connection, which is everything.
Just because it can sub ohm, doesnt mean that it cant plus ohm. Youll be fine from .2 - +3ohm.
You should be able to use it on anything with a 510 connection, which is everything.
Just because it can sub ohm, doesnt mean that it cant plus ohm. Youll be fine from .2 - +3ohm.