Thejackson5
Gold Contributor
Member For 4 Years
Member For 3 Years
Member For 2 Years
Member For 1 Year
Do you know if it is a hybrid mech or not?
Become a Patron!
Whiskey's corner
- Thread starter Whiskey
- Start date
- Status
Do you know if it is a hybrid mech or not?
Straight mech
Holy crap on a cracker!! Please for all the marbles be careful.
Sent from my XT1031 using Tapatalk
Thejackson5
Gold Contributor
Member For 4 Years
Member For 3 Years
Member For 2 Years
Member For 1 Year
What kind of mech is it?
Cuomo clone.
I fail to understand this post
Sent from my XT1031 using Tapatalk
Saw that, too bad some one wouldn't wake up and make it so it takes replaceable coils
f1r3b1rd
https://cookingwithlegs.com/
Staff member
Senior Moderator
VU Donator
Diamond Contributor
VU Challenge Team
Member For 5 Years
VU Patreon
GRIMMGREEN -SO LET IT BE WRITTEN, SO LET IT BE DONE
GOTTA LOVE VAPORSHARK- not a lot know that they do all of that testing; they have been doing that testing n coils, juice and batteries for a few years now.
GOTTA LOVE VAPORSHARK- not a lot know that they do all of that testing; they have been doing that testing n coils, juice and batteries for a few years now.
Thejackson5
Gold Contributor
Member For 4 Years
Member For 3 Years
Member For 2 Years
Member For 1 Year
Im trying to build for my mech. But the resistance keeps jumping from .2-.7 and wont stay stable. Id put this on a %egulated no prob but im nit risking it on a mech
Thejackson5
Gold Contributor
Member For 4 Years
Member For 3 Years
Member For 2 Years
Member For 1 Year
You got a loose leg on your coil somewhere. Start with a simple wrap or twist. Aim for .5 or so to start
Try tightening ur post screws or make sure your leads coming through are not touching other coil...
Sent from my XT1031 using Tapatalk
Hank F. Spankman
Platinum Contributor
Member For 4 Years
Member For 3 Years
Member For 2 Years
Member For 1 Year
Do you have a fire suppression device?
Not gunna be needed.
Im just going simple with this build. And ive been doing reasearch and what not. With the battery im gunna use lowest i can go with out any risk is .2. Im shooting for .35. I refuse to go lower then a .3 flst tho for my first mech build.
Hank F. Spankman
Platinum Contributor
Member For 4 Years
Member For 3 Years
Member For 2 Years
Member For 1 Year
You have a decent ohm meter?
YepYup. Im useing my regulated mods to build on. I like the balrog to build with. The ohm meter moves as i fire it if i got any issues where as the rx wont do that
Im not gunna explode.
Thejackson5
Gold Contributor
Member For 4 Years
Member For 3 Years
Member For 2 Years
Member For 1 Year
@Boattlebot if your trying not to go boom then stop playing with fire. Especially if your using a regulated to build in. Aim for .5 that way if its lower than that and you take a deep hit you will still have your face to exhale from. Get an ohm meter next time you are at the shop. Don't play with the thing, it will bite you.
f1r3b1rd
https://cookingwithlegs.com/
Staff member
Senior Moderator
VU Donator
Diamond Contributor
VU Challenge Team
Member For 5 Years
VU Patreon
Just making sure that you don't make a mess for someone to have to clean up
Got my build done. Ohms out at .3 and stays steady.
Just basic. Nothing fancy.
Just basic. Nothing fancy.
Thejackson5
Gold Contributor
Member For 4 Years
Member For 3 Years
Member For 2 Years
Member For 1 Year
Thejackson5
Gold Contributor
Member For 4 Years
Member For 3 Years
Member For 2 Years
Member For 1 Year
Welp, can't make them understand. Good luck.
Exploding may be an exaggeration. But if you are going down this road having the proper tools is a must. Any thing could go wrong and as the saying goes safety first and foremost. These meters exist for a reason. I build I own mechs and reg devices and ALWAYS use an OHM meter.
Sent from my XT1031 using Tapatalk
Claptons not my choice for a mech build do to ramp time smh.
Sent from my XT1031 using Tapatalk
Thejackson5
Gold Contributor
Member For 4 Years
Member For 3 Years
Member For 2 Years
Member For 1 Year
I have an ohm and multimeter in case the ohm meter shits the bed
Thejackson5
Gold Contributor
Member For 4 Years
Member For 3 Years
Member For 2 Years
Member For 1 Year
At least not dual, too much draw on battery, things get hot
Hank F. Spankman
Platinum Contributor
Member For 4 Years
Member For 3 Years
Member For 2 Years
Member For 1 Year
f1r3b1rd
https://cookingwithlegs.com/
Staff member
Senior Moderator
VU Donator
Diamond Contributor
VU Challenge Team
Member For 5 Years
VU Patreon
Amen there... 24g basic bitch build
Doesn't matter in that build. On a fresh battery he is only putting about 4 volts with sag on build that takes at least 6 volts to ramp up.
Sent from my XT1031 using Tapatalk
f1r3b1rd
https://cookingwithlegs.com/
Staff member
Senior Moderator
VU Donator
Diamond Contributor
VU Challenge Team
Member For 5 Years
VU Patreon
Making sure its not a trustfire or a torn wrapper, 0.3 ohms is fine on most anyway
f1r3b1rd
https://cookingwithlegs.com/
Staff member
Senior Moderator
VU Donator
Diamond Contributor
VU Challenge Team
Member For 5 Years
VU Patreon
I normally would do 24(5wrap) or 22g(6wrap) and build around a 0.18-0.2 ohm with a vtc5.
Or 12-14wraps around a 0.5 on a series box.
That's also after knowing my gear and making sure everything was the way it should be.
That is on the cusp of tard ohm.
Or 12-14wraps around a 0.5 on a series box.
That's also after knowing my gear and making sure everything was the way it should be.
That is on the cusp of tard ohm.
Yeah claptons are nit really for mechs but i got a pair of coils in my grave yard that will be better. But this mech works. Its running my claptons and im not dead. I think ill be ok here.
Once they warm up tho its a nice vape
Hank F. Spankman
Platinum Contributor
Member For 4 Years
Member For 3 Years
Member For 2 Years
Member For 1 Year
What's the "big" paper in those parts @Thejackson5 ?
- Status