Well got my mech I always wanted. Made here in Edmonton Alberta.
What a beauty.
Sent from my SM-G975W using Tapatalk
Thanks jwill. Cant wait to fire it upNice. Those are bad ass.
Thanks jwill. Cant wait to fire it up
Sent from my SM-G975W using Tapatalk
be aware the m41 is not a particularly conductive RDA (got 3 myself). I can see up to .3V of additional drop when moving the same coil to a say a kennedy with square copper posts or a subzero x with silver plated copper posts.try it yourself with a .1ohm buildJust fired up the 3sixty. Man that button. Those magnets are heavy duty. I had to adjust the delrin piece that is located on the switch. Seems to be firing ok. Running a dual coil on the m41 with the 3sixty ohm is 0.22 at 4.2 volts roughly 18.2 amps.
Really loving this mech.
Sent from my SM-G975W using Tapatalk
Thanks for the heads up. I have been eyeing a Kennedy. My vape shop does not have any in atm. I did not know about that issue in the m41. Great information. Thank you.be aware the m41 is not a particularly conductive RDA (got 3 myself). I can see up to .3V of additional drop when moving the same coil to a say a kennedy with square copper posts or a subzero x with silver plated copper posts.try it yourself with a .1ohm build
Thanks for the heads up. I trust my vape shop. It's the one vape shop I go to and no other. Been going there for two years.Don’t buy a Kennedy from anyone other than Kennedy. My opinion.
Thanks for the heads up. I trust my vape shop. It's the one vape shop I go to and no other. Been going there for two years.
Sent from my SM-G975W using Tapatalk
Not about trust. About not paying the shops mark up. Great customer service too I hear and they make the stuff so....Thanks for the heads up. I trust my vape shop. It's the one vape shop I go to and no other. Been going there for two years.
Sent from my SM-G975W using Tapatalk
Thanks for the heads up. I trust my vape shop. It's the one vape shop I go to and no other. Been going there for two years.
Sent from my SM-G975W using Tapatalk
I love the rda. But I do notice that the resistance creeps up every one in a while. Just tighten it down . Seems to be good.sure it's really mostly noticeable from 0.1ohm and below, it's more noticeable on the first one i got (first batch).
I do like the RDA and use it a lot, i like the flavor on it, just wouldnt call it a 'competition' on. Problem is the posts have too many moving parts internally
A cheap and conductive RDA is the Druga RDA, can be found for some $15, with a trinity glass cap is gives some REALLY good flavor and hits quite hard
Overlord custom finish
Used it from the Time I got it set up til bed. It probably won't leave the house. But it's solid as hell. Fire switch has no play or shift and I don't see that it ever will. I'm really happy with it. Had a hard time deciding on what rda though. But the color shift in the finish is amazing. Blue but if you lay it down like in the photo the whole mod turns purple. Really great job Jwill did on these.So what are your thoughts mate?
Check out vaping veterans supply.yeah it has softened a bit over time and it’s not isolated, but it’s a pretty stiff spring even so.
I ended up putting a softer one in from my barebones mech until I source a replacement, but it goes with it really nicely so might just keep it in there
Check out vaping veterans supply.
They have solid silver springs for a few mods.
Sent from Amchitka
Not sure what you're replacing with that spring, but you might want to talk to Jason (owner) @VVS619 before you order. I was a little surprised at the strength of Eric Simpson's springs. I wanted a spring to replace the magnets in my Purge B2B V2 so I ordered the heavy spring and it's way heavier than the magnets. Jason confirmed the heavy spring is stronger than the magnets in the Purge, and the medium is equal to them.Thanks cash will do
Yup. I ordered 2 pairs of each and glad I did because when I got my springs the heavy, was strong. Almost too strong.Not sure what you're replacing with that spring, but you might want to talk to Jason (owner) @VVS619 before you order. I was a little surprised at the strength of Eric Simpson's springs. I wanted a spring to replace the magnets in my Purge B2B V2 so I ordered the heavy spring and it's way heavier than the magnets. Jason confirmed the heavy spring is stronger than the magnets in the Purge, and the medium is equal to them.
marter
That;s the only Goon I don't have now. I have 2 1.5's and an SE copper 25, but no og.Just got the last original goon at my vape store. Little polishing is in order. Bit looks great.
man, i have about 6 goons and never really liked the flavor out of them, only one i found competent flavor wise was the LPYep it is the brass version. I just coiled it and cottoned it up. Man. The flavor compared to the m41. Black and white. Love the flavour out of the goon.
Sent from my SM-G975W using Tapatalk
Got an OG ya wanna get rid of?man, i have about 6 goons and never really liked the flavor out of them, only one i found competent flavor wise was the LP
we are opposite here, the m41 gives me a lot more flavor than the goon.
then again may be my builds
Got an OG ya wanna get rid of?
Doesn't cost anything to askHave a few yes, 22mm black v1, silver v1.5, black 25mm v2, LP (that i'll keep). But not particularly looking to sell them even though i dont use them. I normally bundle RDAs when selling my mods to get some extra value.
Now if you want a purge twistd i'm selling + 25mm goon we can talk
Doesn't cost anything to ask
Sorry I just saw this ,but I don't have anything to trade. That doesn't cost anything to ask eitherOr, yo have an rda i would be interested on? then we can trade a 24mm or 25 for another
Sweet score manStacked 21700 Overpowered limited edition 1/10 picked up this Beauty at the expo...can run it single also ...fantastic clutch switch
View attachment 139842
See your messages please.There is a dude who makes springs from Highlands Texas, does anyone know the dudes name? He is a jeweler and does a lot of really nice springs. I had his card but cant find it and need to get ahold of him. Pretty sure someone here knows who this is, if not any spring maker you trust and recommend would be ideal.
I believe you're thinking of Eric Simpson.There is a dude who makes springs from Highlands Texas, does anyone know the dudes name? He is a jeweler and does a lot of really nice springs. I had his card but cant find it and need to get ahold of him. Pretty sure someone here knows who this is, if not any spring maker you trust and recommend would be ideal.
i have a few different v3 hogs and i love them. the only warning i can offer is that every newer edition i got, the quality control was worse and worse. i got the first v3 and it was perfect. the four horseman edition was good, but some of the screws in the switch/510 area got a bit loose after a while (misfires and weak feeling hits) and i had to take it apart and tighten everything down. the trinity edition was worse than the horseman and i had to take it apart and tighten everything up before i even put batteries in it for the first time. i was surprised to see them shipping like that at this price range, but once its all tight they are pretty much bulletproof in my experience. i would recommend one to anyone who is comfortable with mech mods and likes a hot vapeDoes anyone have a Hammer of God? Do you like it and is it worth the money?
V3 is an awesome Mod, the V4 though is a piece of shit.Does anyone have a Hammer of God? Do you like it and is it worth the money?