General Specifications:
• Quad Post Design
• 316 Stainless Steel
• 22mm Outside Diameter
• ~8.25mm ID POM Drip Cap
• 4 x 1.3mm Hex Drive Post Screw
• ~27.75mm in Height w/ Drip Cap
• ~36.25mm in Height w/o Drip Cap
• 6 x 1.8mm Adjustable Bottom Air Flow
• Drip Cap Doubles as a 510 Drip Tip Adapter
• Not Serialized (No Serial Numbers)
• 2 x 20x1S50 Top Cap Inside O-ring
• Support for Single/Dual Coils
• Bottom Feeding Pin Included
• 2.5mm Hex Drive
• 6-8mm Deep Juice Well• ~44g in Total Weight
Simple Test Build:
Single 22g titanium grade 1 Ø3.75mm 6 wrap. Expected resistance of 0.13Ω to 0.14Ω as measured on a Scotts Mod ORDTS.2 firing multimeter.
[ Kennedy Roundhouse + TIDI Rayon @ 50% Tail Reduction ]
Positive Impressions:
• Can accomodate ≥ 4mm ID single and ≥ 3mm dual builds.
• Shorter than it appears to be. Shorter than the standard K24.
• ~1mm thick top cap speaks to its heavy-duty construction.
• Flavorful even with the additional airflow of the CloudCap.
[ Adjustable 510 Positive = Safe to Use with Direct-to-Battery Mods ]
Negative Impressions:
• A number of hole edges required deburring.
• Corner edges also required deburring = Obvious QA failure.
• Inside silicone O-rings are not nearly as durable as nitrile.
• Two nitrile O-rings are supplied as spare accessories.
• ~8.25mm ID widebore may not be wide enough for some.[ Brush Research Manufacturing Cross Hole Deburring Brush ]
Additional Commentary:
While advertised as a 10mm juice well, a depth gauge proved otherwise with only 6mm measured at the positive section and 8mm at the negative. Moreover, total well capacity is inhibited by the mass consumed by the the air flow tubes. I would have liked to seen the CloudCap designed to support direct-to-coil airflow. Aggregate airflow with the CloudCap is sufficient to feed high mass, single coil builds powered in the 100W range. Inside O-rings require particular care as it is recommended to lubricate them with e-juice, food-grade lubricant, or water before seating the top cap on the deck. For those who object to the use of inside O-rings, it appears that a design compromise was made: Increase the wall thickness of the deck for outside O-ring channels at the expense of well capacity, or retain well capacity by increasing the wall thickness of the cap to accept inside O-rings. One highlight has been the outstanding customer service provided by NoName Mods through Facebook. They are both engaging and responsive which is a credit to them. Final thoughts: I purchased and built the NoPity as a single coil RDA for use with both bottom-feed and non-bottom-feed devices. For that, it has satisfied my expectations with its straightforward coil mount design, acceptable airflow (with the CloudCap) and adequate well capacity. While equally adept at duals, the NoPity has been crafted more along the lines of a flavor chaser with a lower ceiling of support for big, powerful builds owing to its limited airflow options.
Included Accessories:
• 2 x 20x1N70 (Inside) O-ring
• 2 x 20x1S50 (Inside) O-ring
• 2 x 1.3mm Hex Drive Post Screw
• 1 x 1.3mm Hex Key L-wrench
• For Hex Drive Post Screws
• 1 x 1.5mm Hex Key L-wrench• For Hex Drive 510 Positive Pin
• 1 x 2.5mm Hex Key L-wrench• For Hex Drive Bottom Feed Pin
• 1 x 2.5mm Hex Drive Bottom Feed Pin
CloudCap (Accessory):
• 316 Stainless Steel
• 22mm Outside Diameter
• 2 x 20x1S50 Inside O-ring
• 2 x Ø2.5mm Indirect Side Airflow
• Same Size and Weight as Standard Cap
• 2 x 20x1S70 Spare Inside O-ring
• Available as Separate Purchase
[ Note the Domed Chamber & Inside O-rings ]
Authorized Resellers:
• Vapin Art in USA
• Twilight Vape in China
• High Creek in Switzerland
• Vape Villiage in Japan
• VapStor in France
tl;dr: Imperfect, yet perfectly suited as a single coil specialist with support for duals, the strengths of the NoPity are best evident on bottom-fed devices.
Last edited:
.
