Vapor Flask Lite

[Jpm73]

Anyone have a problem with mod saying "atomizer short or low" and device to hot?? I'm wondering if it's my atomizer or the mod. What's the best atomizer for this mod?

 

[AmandaD]

Moving this to the correct forum so you're more likely to get some help!

 

[DevAuto]

Anyone have a problem with mod saying "atomizer short or low" and device to hot?? I'm wondering if it's my atomizer or the mod. What's the best atomizer for this mod?

Any atomizer "should" work.

What is the build on it?

It could be a bad build, or it could be a bad chip, need more information to even begin to make an informed guess. A pure guess without any further information would be that your build ohms are below the chip spec, but that is purely a guess.

 

[Jpm73]

Any atomizer "should" work.

What is the build on it?

It could be a bad build, or it could be a bad chip, need more information to even begin to make an informed guess. A pure guess without any further information would be that your build ohms are below the chip spec, but that is purely a guess.

 

[Jpm73]

I'm pretty new at this. You asked what it's build on? Have no idea lol. Same goes for the chip? Anyway you could break it down easier so I can give u better info?

 

[Wingsfan0310]

What atomizer are you using on the mod? Are you building your own coils or using store bought coils (heads you screw into the atomizer)? Do you have either a second mod or atomizer so you can try and eliminate either the mod or atomizer as the problem?

Cheers,
Steve

 

[eggymaniac]

I could be wrong, but I'm almost positive I'm right. I have one of these, and it has the same 510 connection/spring as the rx200- meaning it's shoddy. It works great until you put an atomizer with too long of a 510 connection on and it ends with the same results as a rx200.

 

[Jpm73]

What atomizer are you using on the mod? Are you building your own coils or using store bought coils (heads you screw into the atomizer)? Do you have either a second mod or atomizer so you can try and eliminate either the mod or atomizer as the problem?

Cheers,
Steve

 

[Jpm73]

I use the kanger subtank mini with SSOCC REPLACEMENT COILS. I put my wife's same tank on and it fired. Mine works but have to watch the ohms to not screw it in to far

 

[Jpm73]

I could be wrong, but I'm almost positive I'm right. I have one of these, and it has the same 510 connection/spring as the rx200- meaning it's shoddy. It works great until you put an atomizer with too long of a 510 connection on and it ends with the same results as a rx200.

 

[Jpm73]

So are you saying it's the mod? If so is there a tank that is better to use with this mod

 

[Wingsfan0310]

I use the kanger subtank mini with SSOCC REPLACEMENT COILS. I put my wife's same tank on and it fired. Mine works but have to watch the ohms to not screw it in to far

Sounds like the 510 pin on the atomizer is longer than your mod is capable of handling. I wonder if your subtank's pin is just a hair longer than your wife's?

A nylon washer, o-ring, or something like making a spacer out of a old credit card might help so the 510 pin isn't screwed into the mod too far.

Cheers,
Steve

 

[eggymaniac]

Sounds like the 510 pin on the atomizer is longer than your mod is capable of handling. I wonder if your subtank's pin is just a hair longer than your wife's?

A nylon washer, o-ring, or something like making a spacer out of a old credit card might help so the 510 pin isn't screwed into the mod too far.

Cheers,
Steve

This. I got in the habit of using a plastic spacer washer on all tanks and rda's, most of the time its never an issue but this all but completely eliminates any potential of such. Also, I like it because if any juice happens to leak out of the 510 or close by it will ring around the washer and stop most, if not all, of the juice from getting down on the connection.