DigiFlavor Pharaoh RTA

[Paratech]

Time for another RTA

It comes with plenty of extras and user manual including nine thousand languages however no actual instructions.













Referencing item on top right of the above pic:
Expansion Tube: 13mm tall including threaded section
10.5mm tall X 27mm OD with huge juice fill holes (5.25mm X 19.5mm)


A few specs:

NOTE: My measurements came out a bit different than DigiFlavor has on their site.
I have verified my measuring instruments have been properly calibrated.

27mm OD tank
Without extension tube:
56.5mm tall including drip tip
46.25mm tall excluding drip tip

With extension tube:
66.5mm tall including drip tip
56.25mm tall excluding drip tip

 

[Paratech]

Drip Tip / Top Cap:
10mm OD 12.6mm tall (including the 2.6mm topcap)
10mm ID at top tapering down to 7mm
If you remove the insert that is in the drip tip;
12.7mm ID at top stepping down to 11mm and then the threading starts for the topcap (9.6mm)
This will NOT take a standard 510 drip tip.




Base:
25.6mm OD
16mm ID at threading for deck
12.5mm deep
13.5mm X 1.9mm air flow holes
Airflow adjustment has hard stops and locks as you adjust to the airflow of your liking.
510 pin is built into deck, not base.

 

[Paratech]

Huge juice fill holes




Top section:
19.7mm tall X 27.1mm OD
Chimney is 7.6mm ID
Air flow holes 9.8mm X 2.25mm with a much smaller inside hole at 2.9mm ID that flows into inside chamber.







Cage:
20.5mm tall X 27mm OD at bottom ring and 20.6mm OD at cage section.
Also has 11.2mm X 1.75mm juice flow holes





Glass:
19.06 tall X 27.04mm OD (without O-rings)

 

[Paratech]

Deck:
28mm tall including 510 pin
14.75 excluding 510 pin
19mm OD
8.3mm gap between the two mounting risers that are 5.5mm tall
7.3mm X 2mm juice flow
3.5mm deep juice well









I opted for a dual coil build because I haven't found a single yet I like.
For all I know this is the worlds greatest RTA with a single coil build in it however it doesn't look like I'll find out.
Nothing special just MKWS Alien @ 3mm ID 0.18Ω
I bent the legs straight out at 90°
I'm sure there are plenty of ways to build this, I am choosing this route.
The spring loaded clamps certainly make it pretty easy.
Wicking was also just as easy.

 

[Paratech]

 

[Paratech]

 

[Paratech]

Extra pics from http://digiflavor.com/project/pharaoh-rta/











Extra pics from http://digiflavor.com/project/pharaoh-rta/

 

[Paratech]

I ordered mine from https://www.efun.top for 39.99 in early March.
I see that you can now get it for $29.95 at https://www.myvaporstore.com/Pharaoh-RTA-by-Digiflavor-and-RiP-Trippers-p/dig-pha10.htm
MVS currently only has the black in stock.
Too bad they didn't have them when I ordered mine, I wouldn't have minded saving $10.
You can get the extra decks for $9.95 here:
https://www.myvaporstore.com/Pharaoh-RTA-Build-Deck-p/dig-pha20.htm
They currently have #2 and #4 in stock.

You'll only get the 4.6ml of juice in IF you use the expansion tube.
Without it, you'll only get 3.2ml.

As I suspected, the top airflow did just as I anticipated.
White it increased the total airflow and provided a bit cooler vape, it also reduced flavor.
I found this particular build best at 100 watts with the bottom airflow and juice flow full open and the top airflow closed.
Awesome flavor and room filling vapor production.

 

[Paratech]

With its flavor and vapor production I think I'm going to have to order the stainless version as well.
Chain vaping made the glass warm but not the top cap / drip tip.
Vapor remained warm to cool @ 100 watts with this build.

 

[SirRichardRear]

Nice write up. Can't wait for mine to arrive

Sent from my SM-G935V using Tapatalk

 

[Deucesjack]

Nice, awesome job.

Sent from my SAMSUNG-SM-G900A using Tapatalk

 

[mjag]

I like the way you review @Paratech and the pics are always great. Thanks bud

Sent from my SM-N910P using Tapatalk

 

[DX9]

You'll only get the 4.6ml of juice in IF you use the expansion tube.
Without it, you'll only get 3.2ml.

Doesn't make sense. I fit 4.5mls with a syringe the day I got it. Went just under the rim at the top. Where you filling it to? I haven't measured with the extension tube but will try later today when I get back home

 

[Paratech]

Doesn't make sense. I fit 4.5mls with a syringe the day I got it. Went just under the rim at the top. Where you filling it to? I haven't measured with the extension tube but will try later today when I get back home

Only filled it to the cross section bars.
Didn't fill it completely to the top to prevent it from seeping out as I threaded the cap on.
Same as I do with all others.

 

[Heartsdelight]

View attachment 79164
View attachment 79165
View attachment 79166
View attachment 79167

Drip Tip / Top Cap:
10mm OD 12.6mm tall (including the 2.6mm topcap)
10mm ID at top tapering down to 7mm
If you remove the insert that is in the drip tip;
12.7mm ID at top stepping down to 11mm and then the threading starts for the topcap (9.6mm)
This will NOT take a standard 510 drip tip.

View attachment 79168
View attachment 79169

Base:
25.6mm OD
16mm ID at threading for deck
12.5mm deep
13.5mm X 1.9mm air flow holes
Airflow adjustment has hard stops and locks as you adjust to the airflow of your liking.
510 pin is built into deck, not base.

View attachment 79170
View attachment 79171
View attachment 79172
View attachment 79173

Beautifully done!

 

[SirRichardRear]

mine finally shipped today. i was waiting on the gold one

 

[Heartsdelight]

mine finally shipped today. i was waiting on the gold one

 

[Paratech]

Looks like the decks are swappable between the DigiFlavor Pharaoh RTA and the GeekVape Griffin 25 mini

 

[Heartsdelight]

Looks like the decks are swappable between the DigiFlavor Pharaoh RTA and the GeekVape Griffin 25 mini

The Mini too? That's great! Djlsb vapes switched the .Griffin 25 Plus tank section with the Pharaoh's as he thought it looked better & makes it lighter.

 

[Atrumitos]

Thanks for the info.

Not sure if I should ask this here. Any comparison between this, the merlin/merlin mini the exo rta, ammit and so on?