Become a Patron!
Lowest Mech Build?
- Thread starter Amj1767
- Start date
CrazyChef v2.0
Platinum Contributor
ECF Refugee
VU Challenge Team
Member For 5 Years
Reddit Exile
VU Patreon
Why?
CrazyChef v2.0
Platinum Contributor
ECF Refugee
VU Challenge Team
Member For 5 Years
Reddit Exile
VU Patreon
Cool. Some of the guys like to go extremely low. Personally, although it's not an answer to your question, I like to stay around 0.20Ω on tubes. It's seems to be my "sweet spot" for flavor.
.1 with a single 20S or 30T, .
.27 in a stacked tube with a pair of 2070C. I had to bring that up to .3. Which is still pretty aggressive.
I once accidentally got 2 similar RDAs mixed up and put a .1 build on a stacked tube with a pair of 20S, which almost torched my head off.
.27 in a stacked tube with a pair of 2070C. I had to bring that up to .3. Which is still pretty aggressive.
I once accidentally got 2 similar RDAs mixed up and put a .1 build on a stacked tube with a pair of 20S, which almost torched my head off.
CrazyChef v2.0
Platinum Contributor
ECF Refugee
VU Challenge Team
Member For 5 Years
Reddit Exile
VU Patreon
Absolutely
I just use a piece of 12 ga copper wire.
I like the fireworks.
I like the fireworks.
Didn't somebody say that brevity was the essence of wit?
More useless drivel to a serious question.
I have built to .1Ω but my MOD's gave me issues when they got HOT.
Don't listen to him @The Cromwell, I thought it was damn funny. 
Drivel or not. I use single cell 18650 so don't like going much below .25 and prefer staying around .3 to .5. .25 drains the battery too quickly for my enjoyment as well as heats the vapor up too much for the same.
I would imagine the regulated mods you use cut off when you try building & firing lower than .20.
Drivel or not. I use single cell 18650 so don't like going much below .25 and prefer staying around .3 to .5. .25 drains the battery too quickly for my enjoyment as well as heats the vapor up too much for the same.I would imagine the regulated mods you use cut off when you try building & firing lower than .20.
Listen to who?
Someone I have on ignore must have said something?
In reality I have never gone lower than .2 I think on a mech.
I like around .3 or so.
I use rta’s on my tube mechs, usually build them .15-.3 and use a 30T or 20S.
Ryan_AlanUSN10
Member For 2 Years
I typically stay at a .1-.16 on any of my mods. The type of coils I prefer just tend to run that low. 4-5 wraps. On a 30T you’re ok. Just gunna drain the battery which is ok I guess i usually keep a spare in my backpack. Although I will be making some coils in the near future that Ide like to get 6-7 wraps out of and probably shoot for a .2ish build. Easier on battery.Edit***
I did get a set of quad core aliens to ohm out at .08 which I couldn’t really run on anything except my drag2 with 2 20s in it. Fucker took forever to heat up and drained the fuck out of my battery. Although once it was going it spit some mean clouds on my NADA
Mechanical king
Bronze Contributor
I had a 0.08 ohm build on my purge twiztid for well over 6 months without issues. While stupid, I dont hit for over 1 second and after I did more research, I quickly changed to a 0.18-0.20 ohm build.
My daily vape is now a 3.5mm parrell wrap 316L SS at .25 ohms on a Kayfun Lite with 30mg saltnic. Why I never tried it 4 years ago I don't know. Could have saved a ton of money venturing into duel battery 200 wattage mods. Wrapped all eight Kayfun lites this way now. Never thought I would use them again but I am back. LOL
Last edited:
Lol looking at the replies some of you are going to think I am insane, I have quad coils 5 wrap corrugated fraliens (ivy coil) and it ohms at .06. I absolutely love it and it's mounted in a strife 28mm. But don't use something like this unless you have a 4 battery mod lol. Or better yet don't try at home, at all.
Attachments
I use 6 coils in my Wild Bull Productions 23mm So Horney (authentic V1) at just a tad below .04 ohms on my Vaperz Cloud Stormbreaker mod that uses only 3 batteries (Samsung 30T).
Last edited: