fused clapton

Hi guys, Im building coils especially for MTL users As a flavor chaser myself I’ve been searching for a long time after the perfect MTL experience, after a long time and many wires I’ve started building the coils for myself by seeking for the best flavor and vapor. Im selling my own handmade...

Parameters: Resistance: 1.3ohm/ft Material: Nichrome 80 Length: 10ft Type: 4-28/40 Package includes: One Box of Quad-Core Fused Clapton Ni80 Wire

Parameters: Material: Ni80 Wrapped: 36GA Resistance: 0.38ohm Kernel: 38GA*29GA Flat*8 Attention: It's Allowed to be ±0.1ohm difference for Prebuilt Coil. Package includes: One Box of Eight-Core Fused Clapton Prebuilt Coil

The only thing that pops into my mind is perhaps a difference in material being used, but I'd like to know if there's any significant difference between e.g. unbranded fused clapton wire (priced at 2-3$ for 5m) and the same (branded) types that cost nearly three times as much (for the same amount).

Hello there, I recently purchased a Drop RDA and Alien Clapton Coils from GV. I'm not new to vaping - doing it for 3 years - but new to RDA's (used normal tanks like the TFV4, TFV8 Baby Beast, Cigpet ECO 12, etc. before). One thing I didn't knew was that a dual coil setup has half the amount of...

I just bought a 24g fused clapton n90, and did a 4/3 coil that reads 0.08 ohms. I tried using it in my voopoo drag mod together with my govad rda single coil and I'm running it in 60watts and noticed that my mod is getting warmer and warmer after a few hits. Should I worry? Am I safe? What...

Sup guys, so i have some (twisted?) fused clapton coils 28/32ga from Rofvape that i wanna but to good use flavour-wise in my peerless rda, with my Smok Alien Mod. So im wondering what would be the perfect wrap-count/diameter for a really flavourfull vape, preferably not very warm, single or...

Greetings all! Figured I get a post on here for anyone else in my position and hoping to help those who are in a similar situation I was in. For those who never really got into dripping, or vaping at high watts, my experiences might not be relevant to you. I mainly vape lower build drippers...

Hello guys! I've been vape on subox mini few months back and just into a regulated tube mod. However, it is not an adjustable wattage mod, it performs like mech mod. The mod name is Smokjoy Gotta God and can power up to 120W. Then I got a clone AURA Rda from my friends and install 2 fused...

So I tried my hand at making some Clapton wire today (24g N80 x 36g n80) and it went incredibly well. Aside from when I went to wrap the coil, the outside wire kept springing out and spacing out. Any tips or tricks as to fixing this? I've heard torching your wire helps with springy-ness. I'm...

Whats up guys, i've had a lot of problems lately with ohms being too low on more complex builds, not sure where the problem.. The most recent was a build tonight, I have 2 pieces of claptoned 28g SS/32g Ni80, and one strand of fused clapton 26g SS/3g NI80 I then wound the three cores (4 pieces...

so i just started building my own coils a few weeks ago and went from a single coil rda to a dual coil rda, and was wondering if for example i usually run my fused clapton as a single at 50w should i be running 2 at 100w to get the same performance out of each coil or will it perform the same at...

Hello All, I just got the Deadalus and want to build some fused claptons. The smallest wire I have is 32 gauge kanthal so I plan on using it for the wrap. I do not plan on using temp control but I am not against using SS cores. So what wire should I use for the cores. I have Kanthal in 22ga -...

first post! been vaping for a while and building but just recently got into building claptons and the like and was trying to get some opinions on wire gauge for micro claptons, I was thinking about 30/40 N80 any recommendations?

Claptons, for me, got a lot easier with this thing. .............. I bought the jig from vaped3d.com and got it in about 5 days ago. I've made about 50 ft of fused Clapton so far in those 5 days and pretty much every inch of it is flawless. I bought an extra clamp just in case the clips...

so i was going to make some fused clapton out of nichrome, but i was running low on nichrome, and i was wondering what would happen if i mixed nichrome and kanthal, more specifically a kanthal core and nichrome outside.

Has anybody else tried this? I found it on ebay

So I made an experiment fused Clapton wire last night. 24g kanthal + 26g kanthal for core and 28g kanthal for outer wrap. Roughly 5.5 wraps around a 2.4mm screwdriver. Steam engine clocks a single coil at 0.366 ohms. I put dual coil in a velocity rda and my ohm meter is reading it as 0.209 ohms...