I'd grab a Diablo, Tres Equis, Castigador, Dimitri, Noisy Cricket, Abaddon, Anubis, Lethal, Subzero Tube, VCT Tubes and a HOG...just to be certain if SHTF your covered for a while and those mods have the least amount of parts and can be easily fixed if it breaks.
Id emphasise the twisted messes stuff since you can pick up the repair kits up too. They'll last forever
If your getting the Diablo, FT has a Full Brass version that is a must! Its built like a tank and its VERY SIMPLE in design and it hits like a train, for $29...Im picking up the Full Copper Dimitri they have also, maybe the Copper Cherry Bomb too....
36g but I wouldnt use anything thinner then that without having it set up loosely or it could break if it snags at all, I made a staggerton with the method yesterday...
does under stretching it cause, or prevent the mohawk effect? is it because it was using two cores instead of three that i have to stretch it out differently?
I used it with 40k last night wrapping up some 3x28k/40k 7 wrap at 3mm for my conqueror last night. First time using the spool tamer. Worked great! Quash I got them months ago!
It sucks, but just trial and error until you get a feel for it. You'll go through a lot of wire figuring it out, but once you do it gets pretty easy to do.
Seeing a picture might help to get in the ballpark....
Next time you're doing (or anyone) some 3x28/38 aliens could you post a pic of properly stretched decore? I enjoy learning things by trial and error and the satisfaction derived, but don't always want to reinvent the wheel.
). Gotta give props to my fellow Canuck, these coils are performing great! Check out his Insta for more!
First try at what Im calling a @f4rr3ll Build! This was probably the most difficult thing so far for me to pull off...the biggest difficulty was to keeo it all together in my fingers while I made little braces to hold it for the outer wrap...
Specs: 28 x .6R/34N80/24N80/38N80
https://gyazo.com/27343da9481b86b23859b33da625e5bc
My wire specs were: 28 x .6R/34N80/24N80/38N80 (.6 Ribbon Parts: 4 Corrugated, 4 for Framing, 20 for the Staggerton Core). I had to start with a Staggered Staple, then Corrugate the Ribbon, then Frame the Corrugated Ribbon then put up the Round wire and then wrap it all up....next time Ill stagger the round wire also, this was just a test to see if I could pull it off.
Its the same size...alien is stretched the same, These are CMMRVapor's vids I clipped. You measure the wrap on top of the cores and try to stretch it to lay over them flat and then naturally wrap around.
I doubt it they would break easily...
Yeah? I was thinking that about my tweezers but I haven't had any issues yet
Ive broke tips on a couple of them..but I always have refiled them back to matching lengths...
Look up CMMRVapor on youtube, his videos are great...
No macro lens, so it'd be shitty, but I'll put up what I got. They don't look much different than my 24g FCs I did up last night, just a tad thicker.@JERUS just do it man. i was all psyched out when i was getting ready to try it and i just said fuck it and went for it. if its gonna work, it will be just like wrapping a fused clapton. if your wraps are not right it simply wont work. you can see if its going to work or not right away. on the set i made last night i was under stretched. my first inch or so of wraps didnt 'catch' so i backed it off and cut the busted part off the wrap, set it all back in the drill and tried again after a little more stretch. it worked but i got that mohawk effect (which indicates i still didnt stretch enough). they still vape like a boss though. thats my advice after making my first two sets. take it with a grain of salt
edit - post a pic of your damn staple coil dude
Boreas?No macro lens, so it'd be shitty, but I'll put up what I got. They don't look much different than my 24g FCs I did up last night, just a tad thicker.
You betcha!
, All my other atomizers are set up too well, figured I'd go with the second deck of the Boreas to give it a whirl.
Its a hell of a RTA...Im getting a black one and then Im heat coloring the SS version....Hopefully it comes out in a nice/bluish purple...You betcha!
Haha, I've abused mine plenty over the months, well, finally broke the tip! Of course the day I say it isn't going to happen. I'd still love a 3mm and 3.5mm ceramic rod for my 28-32g+ core wires at least.
Yea it would be nice for after you coil on the steel to swap it out to ceramic to fire it on of needed....
Yup, I just could see plenty of advantages to it. Trying to pull and stretch a coil of 24g with ceramic may be an issue, but with thinner more pliable wire, it could be quite nice.
Works extremely well on my Tres Equis! Gotta love this setup. Slowly phasing out my regulated mods for my regular usage. Time to pick up another Tres Equis and a Lucifer
First staple completed! Secret to Jerus success is Whisky 
10 .5X.1 ribbon core.
