Post your builds

[aspr]

Fucking fuck. Got two perfect coils out of it. One didn't ramp right and failed. But have the other for when the mage gta shows up today! Going to attempt some ssfc tonight. I have alot of .5r need to use it. What's it good for? 26 frames???

 

[aspr]

Why not

 

[Mystwalker]

Not pretty, but first attempt at a braided coil. Used 3 pieces of 2x28g twisted Kanthal A1, 4 wraps, 0.35 ohms on my COV Wraith sqounker. Bacon bits wicking. Excellent flavor and vapor at 50w, huge clouds and still great flavor @65-70 watts.

 

[Mystwalker]

Fucking fuck. Got two perfect coils out of it. One didn't ramp right and failed. But have the other for when the mage gta shows up today! Going to attempt some ssfc tonight. I have alot of .5r need to use it. What's it good for? 26 frames???

What atty is that? I really like the clamps for capturing the leads, but noone around south Georgia seems to carry any.

 

[aspr]

What atty is that? I really like the clamps for capturing the leads, but noone around south Georgia seems to carry any.

Coilart azeroth. I love it.

Have there new tank on the bench...stand by

 

[Mystwalker]

Coilart azeroth. I love it.

Have there new tank on the bench...stand by

Does it have a bottom feed pin available? Just wondering if it would work on a sqounker..

 

[aspr]

Does it have a bottom feed pin available? Just wondering if it would work on a sqounker..

nope. Just a tank

 

[aspr]

Stupid clothes pin. Doesn't want to run with the stagger. For the weight method do I just tie a fishing weight and do the loop the whole way???

 

[aspr]

Stupid clothes pin. Doesn't want to run with the stagger. For the weight method do I just tie a fishing weight and do the loop the whole way???

 

[whiteowl84]

Stupid clothes pin. Doesn't want to run with the stagger. For the weight method do I just tie a fishing weight and do the loop the whole way???

Look at mine. See how I leave one side naked? That's so the teeth lock on the bottom. Before I did that it would spin off eventually.

I clip it on so the part you squeeze is towards the ground and I hold the spool over it. Before I was doing it so I could hold the spool like I normally would bit the weight of the clip would bounce the wire.


You can loop the whole way but you need the swivel lower than the drill or the wire will sag and the clapton won't carry the weight back up. If your spool wire isn't at the exact same angle the entire time your gaps can be off.

 

[aspr]

as promised. Coilarts new mage gta

 

[whiteowl84]

Damn. It looks great.

 

[aspr]

It's a nice little tank. Lots of room

 

[CrazyChef]

Coilarts new mage gta

Dammit. Now I had to go and get one from Gearbest. it's all your fault.

 

[aspr]

Dammit. Now I had to go and get one from Gearbest. it's all your fault.

I'll buy some Dotmod shit one day to make up for it lol

 

[aspr]

Double, please delete

 

[whiteowl84]

I've used usps for everthing vaping related. Never an issue for my packages. My macro was sent via ups. Then this happens:

I live in KY btw.
From Florida to my back door then to New York. Ugh.

 

[aspr]

I've used usps for everthing vaping related. Never an issue for my packages. My macro was sent via ups. Then this happens:

I live in KY btw.
From Florida to my back door then to New York. Ugh.

There's a reason why those trucks are brown

 

[whiteowl84]

Lol.
I'm still trying to stagger fuse over 0.3mm but the frames and the ribbon always end up in a twist. Like the frames keep pushing the ribbon out.
They fuse perfectly as far as the spacing goes but I can't keep the ribbon in there.

I'm thinking about ordering some magnets and spool tamers off ebay. Are neodymium magnets too strong?
I found some 25mm x 5mm round ones that are perfect but I'm afraid they might be too strong.

 

[aspr]

Lol.
I'm still trying to stagger fuse over 0.3mm but the frames and the ribbon always end up in a twist. Like the frames keep pushing the ribbon out.
They fuse perfectly as far as the spacing goes but I can't keep the ribbon in there.

I'm thinking about ordering some magnets and spool tamers off ebay. Are neodymium magnets too strong?
I found some 25mm x 5mm round ones that are perfect but I'm afraid they might be too strong.

Try your local hardware store first. Like mom and pop places. Just ask for magnets

Your closest home depot will have some too
http://m.homedepot.com/s/Magnets?searchtype=text&NCNI-5

 

[whiteowl84]

I live in a small town but my hardware store or tractor farm supply may have them. Thanks, I don't even bother looking there anymore but magnets are pretty common so it's a maybe.

 

[MR.G.]

Lol.
I'm still trying to stagger fuse over 0.3mm but the frames and the ribbon always end up in a twist. Like the frames keep pushing the ribbon out.
They fuse perfectly as far as the spacing goes but I can't keep the ribbon in there.

I'm thinking about ordering some magnets and spool tamers off ebay. Are neodymium magnets too strong?
I found some 25mm x 5mm round ones that are perfect but I'm afraid they might be too strong.

If the wire being used to fuse everything together is to heavy this can happen.

 

[aspr]

I live in a small town but my hardware store or tractor farm supply may have them. Thanks, I don't even bother looking there anymore but magnets are pretty common so it's a maybe.

I feel ya. I'm 20 miles from the closest store

 

[whiteowl84]

If the wire being used to fuse everything together is to heavy this can happen.

It's 38g or 36g. I think I know what the issue is now.
I got a new (used) drill today!
Fast enough for clapton, slow enough for staggering, good chuck, ball bearings, no cord and three batteries!

 

[jbone6977]

It's 38g or 36g. I think I know what the issue is now.
I got a new (used) drill today!
Fast enough for clapton, slow enough for staggering, good chuck, ball bearings, no cord and three batteries!

I have Makita, Hitachi, and Dewalt cordless drills in my truck, have used em all to make some coils but they all sucked, claptons n fused claptons were no problem but I couldn't do anything else because of the chuck, bought a $17 POS 18 volt from Walmart with a chuck that is more suited to what I needed and never looked back, multi cored builds got much easier

 

[aspr]

http://m.homedepot.com/s/Magnets?searchtype=text&NCNI-5

 

[whiteowl84]

I have Makita, Hitachi, and Dewalt cordless drills in my truck, have used em all to make some coils but they all sucked, claptons n fused claptons were no problem but I couldn't do anything else because of the chuck, bought a $17 POS 18 volt from Walmart with a chuck that is more suited to what I needed and never looked back, multi cored builds got much easier

Well my $30 AC drill from Walmart works great for any clapton but the chuck is crap and there is no slow. My Rigid is perfect but the chuck only closes to 1/4" so it takes a ton of binding to make it bite. It's the only drill I had that was sensitive enough to stagger fuse so that got old fast.
This one has a better chuck than either and it goes pretty slow. Got it for $35, listed at $60 or $70.

http://m.homedepot.com/s/Magnets?searchtype=text&NCNI-5

My buddy said walmart has them in the arts and crafts section. However I'm not totally convinced it's the paperclips that are failing.

 

[CrazyChef]

I decided to start going a little larger than the norm on the frames for framed staples, and really like it better.
0.4 ribbon using 26g frames.

 

[whiteowl84]

Looks nice dude.

 

[CrazyChef]

Thanks

 

[jbone6977]

Decided to build a set of aliens and a set of 26/40 fused claptons for the tsunamis, first time using 40 and I'm digging it. Will redo the griffin 25s tomorrow and maybe the avocado 24s. Decisions decisions

 

[aspr]

I decided to start going a little larger than the norm on the frames for framed staples, and really like it better.
0.4 ribbon using 26g frames.

View attachment 67773

42 outer?

 

[CrazyChef]

44, 6 cores

 

[aspr]

44, 6 cores

Have some 50g to try, will probably start with just a fused clapton to see how it goes

 

[CrazyChef]

The last time I used 50g for staples I got through about 3/4 of a 10" stick before it snapped. I just came back in from the other direction and the coils ended up perfectly fine.

 

[mikekscholz]

just attempted my first staggered fused clapton and its far from perfect, but better than I expected I would do

 

[FΛDED]

Not a "pro" micro like @CrazyChef @MR.G. @Qlippoth or @raymo2u but just showing some 3 post centered skills, 7 wrap on a 3.5, my own Aliens.

 

[TRONCAT]

Did a solid 24-26 parallel build, 8 wraps around a 3.4mm, came out to .3 ohms. Loving the flavor and vapor off of it

Sent from my XT1575 using Tapatalk

 

[TRONCAT]

Not a "pro" micro like @CrazyChef @MR.G. @Qlippoth or @raymo2u but just showing some 3 post centered skills, 7 wrap on a 3.5, my own Aliens.

Why is it pink? It's beautiful

Sent from my XT1575 using Tapatalk

 

[aspr]

Why is it pink? It's beautiful

Sent from my XT1575 using Tapatalk

He fired them, then set it down and snapped the pic

 

[FΛDED]

Why is it pink? It's beautiful

Sent from my XT1575 using Tapatalk

The camera filtered it as hot pink but it was glowing red like normal.

 

[FΛDED]

He fired them, then set it down and snapped the pic

Yup, lol.

 

[jbone6977]

Decided to build some aliens for the griffin 25, first time stuffing aliens in a griffin and first time running them on the wrecker, works great.

 

[mikekscholz]

Decided to build some aliens for the griffin 25, first time stuffing aliens in a griffin and first time running them on the wrecker, works great.View attachment 67850

Very nice, sir.


Sent from my iPad using Tapatalk

 

[aspr]

progress...

 

[mikekscholz]

Very nice to you too sir! I splurged a little and ordered a spin lt this morning I'm on my last pack of swivels I got when I first started spinning and all the rest have seized on me.

 

[pizzadave80]

New twisted build I'm trying out.

Sent from my SM-G935V using Tapatalk

 

[midknight420]

New twisted build I'm trying out.

Sent from my SM-G935V using Tapatalk

Specs?

I'm not crazy, my mother had me tested.

 

[pizzadave80]

It's just 26g kanthal twisted together. Wrapped 5 times with a 3mm ID. Comes out to. 26ohms.

Sent from my SM-G935V using Tapatalk

 

[midknight420]

It's just 26g kanthal twisted together. Wrapped 5 times with a 3mm ID. Comes out to. 26ohms.

Sent from my SM-G935V using Tapatalk

I was thinking of doing a single coil of the same thing on my Theorem for the NC. Curious how it will vape.

I'm not crazy, my mother had me tested.