Become a Patron!

Post your builds

raymo2u

VU Donator
Platinum Contributor
Member For 4 Years
Unlisted Vendor
This thread alone had made my wife so happy, with the constant arrival of spools of wire and me running a drill to clapton, and my cussing when I don't keep a tight wrap.

Looks like she is going to be happy again when more wire shows up! Haha

Need to have this stuff delivered to work!

Sent from my SM-G925V using Tapatalk
I wish it was cheaper to get and wish it came in bulk spools... 5000ft spools of each wire sounds like a nice tax time purchase
 

raymo2u

VU Donator
Platinum Contributor
Member For 4 Years
Unlisted Vendor
TEMCO sells half pound, pound, and 1.5 pound spools.
One pound of 32g N80 (5,463 feet) is $142.59.
Yea but they dont have much above 32g-35g, its 38g+ I want those 1lbs spools o_O

I am going to pick up a 52g 100ft to try out. My thought it if I cant shrink the size of some of these big builds I could take advantage of the same experience with RTA's/RDA's/Tanks that you cant use them in normally. Say the Goblin Mini, I could barely fit that single stretched clapton wire into the chamber without touching due to its size. What if I made a Staggerd Fused Clapton in 38g/52g? It would be a PITA at first but after using it for a bit it might open up new doors and opportunities like the example...
 

martinelias

Silver Contributor
Silver Contributor
Member For 4 Years
Member For 3 Years
Member For 2 Years
Member For 1 Year
Yea but they dont have much above 32g-35g, its 38g+ I want those 1lbs spools o_O

I am going to pick up a 52g 100ft to try out. My thought it if I cant shrink the size of some of these big builds I could take advantage of the same experience with RTA's/RDA's/Tanks that you cant use them in normally. Say the Goblin Mini, I could barely fit that single stretched clapton wire into the chamber without touching due to its size. What if I made a Staggerd Fused Clapton in 38g/52g? It would be a PITA at first but after using it for a bit it might open up new doors and opportunities like the example...
You can wrap that 38/52 over something like 32 or 28 and make something special.

Sent from my SM-N920T using Tapatalk
 

MidwestExpress

Silver Contributor
Member For 4 Years
You can wrap that 38/52 over something like 32 or 28 and make something special.

Sent from my SM-N920T using Tapatalk
I found some 52 awg that I am tempted to buy just to I can see what it is like to both build with and vape with. I wonder if that is getting too small to have the same affect on a clapton. So small that it is almost sealing the inner core. Then again I am only learning and have never worked with it... could be the holy grail or it could be like opening and looking into the ark of the covenant!

images
 

raymo2u

VU Donator
Platinum Contributor
Member For 4 Years
Unlisted Vendor
I found some 52 awg that I am tempted to buy just to I can see what it is like to both build with and vape with. I wonder if that is getting too small to have the same affect on a clapton. So small that it is almost sealing the inner core. Then again I am only learning and have never worked with it... could be the holy grail or it could be like opening and looking into the ark of the covenant!

images
So far my experience is the smaller the gauge the wire thats on the outside of a clapton, the smoother the glow pattern is. I havent tried anything above 46g but I would expect somewhere along the same line...You can see with thinner outer wire in these pics the glow is much softer and smoother from inside out.
First Pic: 24g/32g Second Pic: 26g/40g
20150923_151335.jpg 20151111_103104.jpg
 

Attachments

  • 20151111_103104.jpg
    20151111_103104.jpg
    450.4 KB · Views: 18

raymo2u

VU Donator
Platinum Contributor
Member For 4 Years
Unlisted Vendor
I have to go to Walmart I can't wait for these swivels any longer!!!!


Sent from the lab in my basement of vapement
Im going to find something better then fishing swivels...All the swivels I have bought have locked up and now bind when using them(They are ball bearing). I was thinking of rigging something up from my R/C Hobby..Maybe a Bulkhead, CVD shaft and the bearing I use for them, the bearing for RC are rated for 50k rpm and can take abuse without binding..Ill report back if I get something to work out.
 

CrazyChef

Custom Hand Crafted Coils - PureCoils.com
VU Vendor
VU Donator
Platinum Contributor
Member For 4 Years
ECF Refugee
OOPS!
I thought each of the rolls in the bulk packs was 100 feet - they're only 10 feet each. Damn, I thought that was cheap...
Contacted and said I want to cancel and a store credit is fine. I hope they cancel...

@LightningVapes
 
Last edited:

raymo2u

VU Donator
Platinum Contributor
Member For 4 Years
Unlisted Vendor
K I have something that can be used plus I used a part that ill make it completely adjustable afterwards!
The rear of it...
20151111_181204.jpg
The Front, I will fish my wire through the CVD Joint hole, as you can see there is a thin slot and a wide open hole, thin slot for flat wires and round for big round builds lol
20151111_181154.jpg
 

Dawn0810

Gold Contributor
Member For 4 Years
Member For 3 Years
Thanks, @Dawn0810 . Just bought 3,000 feet (3 bulk packs). It's all your fault. :p

Crap.
Hehe I bought 1,000 of 36&40 250 of 26&24 and 100 of all 3 ribbon wires they carry all nichrome I think it's funny for 14$ you get 500 ft but for 5$ more you get 1000ft I have no idea what 1000ft of wire even looks like lol


Sent from the lab in my basement of vapement
 

raymo2u

VU Donator
Platinum Contributor
Member For 4 Years
Unlisted Vendor
Hehe I bought 1,000 of 36&40 250 of 26&24 and 100 of all 3 ribbon wires they carry all nichrome I think it's funny for 14$ you get 500 ft but for 5$ more you get 1000ft I have no idea what 1000ft of wire even looks like lol


Sent from the lab in my basement of vapement
Like a chrome edged frisbee!
 
Last edited:

Dawn0810

Gold Contributor
Member For 4 Years
Member For 3 Years
OOPS!
I thought each of the rolls in the bulk packs was 100 feet - they're only 10 feet each. Damn, I thought that was cheap...
Contacted and said I want to cancel and a store credit is fine. I hope they cancel...
They should they're pretty good


Sent from the lab in my basement of vapement
 

iLiptiKal

Bronze Contributor
Member For 4 Years
At the pivot point where you connect your wires, how easily does it spin? It looks like it's pretty heavy...


Sent from my iPhone using Tapatalk
 

raymo2u

VU Donator
Platinum Contributor
Member For 4 Years
Unlisted Vendor
At the pivot point where you connect your wires, how easily does it spin? It looks like it's pretty heavy...


Sent from my iPhone using Tapatalk
Like Oiled Glass on Marble, less tension then with the original swivels I was using. I may end up using my file set to smooth the edges of the insert holes though. Its size looks massive but its moving parts are no bigger then the swivels.
That CVD shaft is made from Nitrate treated Titanium so its smooth, very light but durable
Video of Swivel Testing
 
Last edited:

wr3ckin_it

Member For 4 Years
Member For 3 Years
Member For 2 Years
Member For 1 Year
I found some 52 awg that I am tempted to buy just to I can see what it is like to both build with and vape with. I wonder if that is getting too small to have the same affect on a clapton. So small that it is almost sealing the inner core. Then again I am only learning and have never worked with it... could be the holy grail or it could be like opening and looking into the ark of the covenant!

images
I love the 40g builds Lightning Vapes has a 250' roll for around $10? I can't remember exactly but it was pretty cheap

Sent from my SM-N900V using Tapatalk
 

Dawn0810

Gold Contributor
Member For 4 Years
Member For 3 Years
Ok I got a ? When making alien wire how do you get three wires stable on a swivel I get the fused Clapton but how do you get the third stable I haven't watched any vids yet so I thought I'd ask


Sent from the lab in my basement of vapement
 

raymo2u

VU Donator
Platinum Contributor
Member For 4 Years
Unlisted Vendor
Ok I got a ? When making alien wire how do you get three wires stable on a swivel I get the fused Clapton but how do you get the third stable I haven't watched any vids yet so I thought I'd ask


Sent from the lab in my basement of vapement
You pray it stays stable and flat :p
You could use 2 dimes and tape it loose and keep it close to your wire being wrapped on and slide it up the wire as you go
 

CrazyChef

Custom Hand Crafted Coils - PureCoils.com
VU Vendor
VU Donator
Platinum Contributor
Member For 4 Years
ECF Refugee
Take the 3 wires and bend them at a right angle (only about the top 1/2 inch or less). Then turn the wires to fit in the chuck of your drill in...

Crap, this is hard to explain...

Here's a good video:
 

wr3ckin_it

Member For 4 Years
Member For 3 Years
Member For 2 Years
Member For 1 Year
Ok I got a ? When making alien wire how do you get three wires stable on a swivel I get the fused Clapton but how do you get the third stable I haven't watched any vids yet so I thought I'd ask


Sent from the lab in my basement of vapement
A paperclip works well too or taping it periodically like every 4 - 5 inches if you're making a longer wire for multiple builds

Sent from my SM-N900V using Tapatalk
 

Dawn0810

Gold Contributor
Member For 4 Years
Member For 3 Years
A paperclip works well too or taping it periodically like every 4 - 5 inches if you're making a longer wire for multiple builds

Sent from my SM-N900V using Tapatalk
I saw that I'm def going to be using that method until I get the hang of it


Sent from the lab in my basement of vapement
 

CrazyChef

Custom Hand Crafted Coils - PureCoils.com
VU Vendor
VU Donator
Platinum Contributor
Member For 4 Years
ECF Refugee
I get the urge to shank you everytime I see your progress :D:p
This is literally one of those "If I can do it, anyone can do it" type situations. I would just ogle at pics of alien coils when I first started and wish I could do stuff like that. You're gonna get there.

Don't forget, this was my first build (SERIOUSLY!):
DSC_00191.jpg


And my 2nd build:
New-Build.jpg
 

raymo2u

VU Donator
Platinum Contributor
Member For 4 Years
Unlisted Vendor
My first build ever was a Clapton 28g on 28g because it was what I bought and I wanted to dive into advanced builds immediately, I had Tanks/Pens and premade coils before that but Im a run first then learn to walk kind of guy. I found out shortly after my Hobo V2.1 arrived that RDA's looked bigger on my screen then in real life and since then Ive tried to make smaller advance builds to fit more applications.
 

raymo2u

VU Donator
Platinum Contributor
Member For 4 Years
Unlisted Vendor
What Ive been using in my TVF4 TF-R1 RBA since yesterday after the Fused Clapton just kept eating cotton...This is the highest resistance build I've used in almost 6 months and I'm glad I used it instead of rebuilding it. I slowly stepped up from 20w and kept going up to 65w and it still wasn't hot and had not the slightest hint of any dryness in the cotton(with chain vaping).
26g/34g Clapton 8 wrap (1.40 Ohms)
20151112_083457.jpg 20151112_083519.jpg
MY friends that vape thought it was insane that it competes with my other low builds for vapor production but the flavor is incredibly strong. The only part I dislike is the draw time, I prefer 3-4 second pulls and I feel the need to draw almost 6-7 seconds on this for satisfaction.
 

MidwestExpress

Silver Contributor
Member For 4 Years
What Ive been using in my TVF4 TF-R1 RBA since yesterday after the Fused Clapton just kept eating cotton...This is the highest resistance build I've used in almost 6 months and I'm glad I used it instead of rebuilding it. I slowly stepped up from 20w and kept going up to 65w and it still wasn't hot and had not the slightest hint of any dryness in the cotton(with chain vaping).
26g/34g Clapton 8 wrap (1.40 Ohms)
View attachment 33610 View attachment 33609
MY friends that vape thought it was insane that it competes with my other low builds for vapor production but the flavor is incredibly strong. The only part I dislike is the draw time, I prefer 3-4 second pulls and I feel the need to draw almost 6-7 seconds on this for satisfaction.
Change your mode to hard or max. That ramps up the first couple second of trigger pull up to 15%. I use that with all my fused claptons. Let's me stay in the lower watts but still not way forever for ramp up.

Sent from my SM-G925V using Tapatalk
 

juicy76

Silver Contributor
Member For 4 Years
Member For 3 Years
OK so I need a bit of help I think... I went and broke down buying a new box mod .I know what you are thinking ...lol what could he possibly needing help with?.. Lol well.. First thing is. How the hell do you clear all settings? I bought the cube x ll. Secondly I went in to my b&m buying 30 & 32 awg n80. Will they work? If so... What I am trying to do is a simple duel parallel build at .1 considering only getting a very small amount. New to temp control but buy no means new to the game... Can I get a little help please.
Thank you in advance
 

MidwestExpress

Silver Contributor
Member For 4 Years
OK so I need a bit of help I think... I went and broke down buying a new box mod .I know what you are thinking ...lol what could he possibly needing help with?.. Lol well.. First thing is. How the hell do you clear all settings? I bought the cube x ll. Secondly I went in to my b&m buying 30 & 32 awg n80. Will they work? If so... What I am trying to do is a simple duel parallel build at .1 considering only getting a very small amount. New to temp control but buy no means new to the game... Can I get a little help please.
Thank you in advance
I will pm you... I have that mod

Sent from my SM-G925V using Tapatalk
 

wr3ckin_it

Member For 4 Years
Member For 3 Years
Member For 2 Years
Member For 1 Year
OK so I need a bit of help I think... I went and broke down buying a new box mod .I know what you are thinking ...lol what could he possibly needing help with?.. Lol well.. First thing is. How the hell do you clear all settings? I bought the cube x ll. Secondly I went in to my b&m buying 30 & 32 awg n80. Will they work? If so... What I am trying to do is a simple duel parallel build at .1 considering only getting a very small amount. New to temp control but buy no means new to the game... Can I get a little help please.
Thank you in advance
Not sure how to clear the settings on the cube x2 but if you download the app maybe you can do it from there. Are you looking to do temp control or suggestions for a build that low?

Sent from my SM-N900V using Tapatalk
 

juicy76

Silver Contributor
Member For 4 Years
Member For 3 Years
Did DL the app but don't see anything in reference to clearing settings... Lol.ugg
 

wr3ckin_it

Member For 4 Years
Member For 3 Years
Member For 2 Years
Member For 1 Year
I have one and yes need suggestions
A 24g 5 wrap kanthal parallel with 28g/32g 4 wrap n80 clapton coiled around a 2.4mm screwdriver should run about .09 - 0.12

Sent from my SM-N900V using Tapatalk
 

juicy76

Silver Contributor
Member For 4 Years
Member For 3 Years
Thank you but I have 30 &32 n80 with 24 awg kanthal.
The 30 & 32 n80 I only bought 2 ft
 

wr3ckin_it

Member For 4 Years
Member For 3 Years
Member For 2 Years
Member For 1 Year
Thank you but I have 30 &32 n80 with 24 awg kanthal.
The 30 & 32 n80 I only bought 2 ft
Hmmmm how about twisting the 30g and then clapton wrap it with 32g? Should come out about the same.

Sent from my SM-N900V using Tapatalk
 

MidwestExpress

Silver Contributor
Member For 4 Years
2d90118c47935467fee23ea8622be5d7.jpg


Better pic of coil with cotton in. Now to adjust the temp and juice this bad boy!

Sent from my SM-G925V using Tapatalk
Ok, now that I figured out the tc on cube 2 I rebuilt this coil. Comes out to .18 ohm. Running this dude at from 250 to 400 so far. 400 still gives super cool vape and bod flavor. Going to hit some higher temp tomorrow and see how flavor goes.

Sent from my SM-G925V using Tapatalk
 

juicy76

Silver Contributor
Member For 4 Years
Member For 3 Years
Ok, now that I figured out the tc on cube 2 I rebuilt this coil. Comes out to .18 ohm. Running this dude at from 250 to 400 so far. 400 still gives super cool vape and bod flavor. Going to hit some higher temp tomorrow and see how flavor goes.

Sent from my SM-G925V using Tapatalk
What are the specs of your build please in detail if possible. I have the same box mod and in the learning curve as well. NiChrome awg size driver to wrap number of times wrapped. Thank you in advance
 

VU Sponsors

Top