I need some of those specs. Look like they could help a lot
Sent from my Nexus 6P using Tapatalk
Become a Patron!
Post your builds
- Thread starter Vape_geek
- Start date
Sent from my Nexus 6P using Tapatalk
They do help a bit - just up to 3.5x magnification but that means the lenses can be about 8 inches away from your work rather than 1 inch like higher powered specs lol
- the lower powered lenses can be worn even farther away than that, havent tried them yet but I will
I feel they are useful, as well as dashing, also fairly comfortable (by Vorey on Amazon for $12)
I made a clean pair of SSFCs but I experimented with skip fusing just for the fun of it and they didn’t turn out bad. 26g frames/4 ply .5 ribbon/38g
I love this build Ray, this one in particular looks like it could be a great vape. When I see these pics “badass build” comes to mind immediately. I’m loving it.Now for some Wide Loads
28g Frames, 6ply .3R, .3x.3 Square Wire, 5ply .3/46g Staples, 42g Stagger and Fuse
30mm Mask RDA
jwill
The Great King of Nothing
VU Donator
Platinum Contributor
Member For 2 Years
VU Challenge Team
Reddit Exile
VU SWAT
Woot finally made a pitchfork! (I think)
looks cool as hell dude.
Good jobLittle build in the Wotofo Warrior. I really dig this rda!
Sent from my SM-G965U using Tapatalk
Oooh Echidna, knuckles was my favorite.
Damn right.
Dual Fraliens, SS 2x30g, 8x.3r, N80 36g
3mm id, 0.09 ohms
3mm id, 0.09 ohms
Looks like stacked coins that were previously ran over by a train.
EXECUTION
Winner: Pegleg Meg! ;D
That was the funnest part, I never melted AND smushed together a coil before. My ceramic tweezers turned red
CrazyChef v2.0
Platinum Contributor
ECF Refugee
VU Challenge Team
Member For 5 Years
Reddit Exile
VU Patreon
You need these:
I really want those... they make so much sense. And it seems way more coilsmith than screwdrivers heheh
Thanks, Kingpin picked enigmas/hedgehogs, so I made some dang enigmas/hedgehogs/whatever
You’re pulling way, way ahead of me! I gotta hit the gas!!
You’re pulling way, way ahead of me! I gotta hit the gas!!
Try it! If you can alien or mohawk you can do this - work around a decore gauge of 1/6th the width of the stick- then you can get regular enigmas, or the three hump things I made
More braiding. 36g 5 loop over 2x26g. I tried pulling differently, kinda cool but lots of space.
Got juuust enough for a coil!
Got juuust enough for a coil!
I’m gonna be up all night trying to nail this build. I think technically enigmas are interlocking but I can see yours are stitched which I actually like the look of better.
I’m gonna be up all night trying to nail this build. I think technically enigmas are interlocking but I can see yours are stitched which I actually like the look of better.
Enigma is just a variation of alien, like mohawk is - stitching, interlocks, are all "add-ons" as I see them lol
More braiding. 36g 5 loop over 2x26g. I tried pulling differently, kinda cool but lots of space.
Got juuust enough for a coil!
That looks really cool
BoostedTrini
Member For 4 Years
This happens when the Alien is loose on there. Happens a whole lot when you use little tension and stretch SS like you do Nichrome(or Kanthal). Go with less stretch next time and it'll coil easier than the Kanthal wrapped ones did.
P.S. For Alien Framed Staples, if you can slide the Alien wrap before you coil it...it ain't going to coil well. The wrap will be too loose to stop the ribbon from laying on their broad side.
Ahhh yeah. I do tend to stretch to the max, plus I made 26g decores and didnt even think about making the stick width right, for the SS ones - got lucky they wrapped at all hehe
Yea I’m in love with 30g/.3 fraliens.
Beautiful Fraliens!!!
Wow that’s such a cool braiding concept. Braids never quite worked out for me but that looks like a great vape!More braiding. 36g 5 loop over 2x26g. I tried pulling differently, kinda cool but lots of space.
Got juuust enough for a coil!
Hey Meg did you use a 6:1 ratio or a 9:1 ratio for this build it looks so clean?
It really is clean. Like some Raymo type coils hereHey Meg did you use a 6:1 ratio or a 9:1 ratio for this build it looks so clean?
Sent from my Nexus 6P using Tapatalk
Hey Meg did you use a 6:1 ratio or a 9:1 ratio for this build it looks so clean?
6:1 - 30g (0.255mm) decore, and stick was 7x.4+2x26 (1.5mm)
And thanks - the magic of angles and photography hide the two messups (and it didnt really coil well on the outside wraps)
Last edited:
man, talk about kitting a single coiler out for a min. NICE!Fraliens and some 26-30-26-30-26 core aliens
View attachment 115891
View attachment 115892️the difference between 26 and 30g up close is crazy
For a single coil kinda guy
️the difference between 26 and 30g up close is crazySent from my SM-G955U using Tapatalk
how is that rda?Fralien I threw in the Revolver RTA. 26 frames, 9x.5 cores, 40 wrap. Nichrome 80. .10 ohms exactly.
Sent from my SM-G955U using Tapatalk
Sent from my SM-G955U using Tapatalk
Vandy Vape Revolver RTA. Very nice! I like the customizable airflow! Flavor is a solid B+ to A-. I don't really judge cloud as a flavor chaser; but cloud is dense and thick.
Sent from my SM-G965U using Tapatalk
Weird thing is I tried it both ways, neither came out well enough to post, but I noticed in small sections the 6:1 ratio only gives you one bump on each side. I think that’s an enigma. You get 3 bumps when you do a 9:1 ratio. I think that’s a hedgehog. I could see that in small sections for sure.
Weird thing is I tried it both ways, neither came out well enough to post, but I noticed in small sections the 6:1 ratio only gives you one bump on each side. I think that’s an enigma. You get 3 bumps when you do a 9:1 ratio. I think that’s a hedgehog. I could see that in small sections for sure.
What gauge were your cores? I could get both one bump or two bumps depending on the stretch, on one side, and either two or three on the other side, depending on stretch
Mine changed when I coiled it - I should try again and coil it the opposite side up and see